Mada za sehemu hiiInstalling control of three phase AC motorsMada 7
- Installing DOL by using the jogging method
- Installing a DOL starter self-holding
- Installing a DOL starter with remote control
- Installing DOL with forward and reverse motor control starter
- Installing manual star delta starter
- Installing automatic star-delta starter
- Installing a rotor resistance starter for slip-ring motor
A slip-ring (wound-rotor) motor uses resistors connected in the rotor circuit to control starting current and torque. By adding external resistance during startup, we reduce the high inrush current that would otherwise damage the supply and increase the starting torque to move heavy loads. As the motor accelerates, the resistance is gradually cut out until the rotor is short-circuited for normal running.
Unlike squirrel-cage motors, slip-ring motors have their rotor windings connected to external circuits through slip rings. This allows us to insert external resistors into the rotor circuit:
- Starting current reduction: When the motor is switched on, the rotor is stationary and the induced voltage is high, causing very high currents (up to 7 times rated current). Adding resistance limits this current.
- Increased starting torque: With resistance in the rotor circuit, the current is shifted to produce more torque rather than just heat. This helps start loads that require high starting torque.
- Smooth acceleration: As the motor speeds up, progressively cutting out the resistance gives smooth acceleration to full speed.
A slip-ring motor has three main parts:
- Stator — the stationary part with three-phase windings connected to the supply
- Rotor — the rotating part with windings brought out to slip rings
- Slip rings and brushes — metal rings on the rotor shaft that make electrical contact with the stationary brushes, allowing external resistance to be connected
A rotor resistance starter is a panel containing:
- Variable resistors (or resistor banks) connected in series with the rotor windings
- Selector switch or drum controller to gradually reduce resistance as the motor speeds up
- Terminals for connecting to the motor's slip-ring brushes
Follow these steps to install a rotor resistance starter:
-
Prepare tools and equipment — Gather screwdrivers, spanners, multimeter, pliers, and all safety gear (boots, goggles, gloves, overalls).
-
Mount the motor — Secure the slip-ring motor firmly on the work bench or mounting base.
-
Connect the stator — Wire the three-phase supply to the stator terminals (U, V, W) using appropriate cable size.
-
Connect rotor leads — Identify the three rotor terminals brought out through slip rings. Connect these to the starter's resistor terminals.
-
Wire the control circuit — Connect the starter's selector switch or controller according to the wiring diagram. Ensure the controller allows gradual reduction of resistance.
-
Check all connections — Use the multimeter to verify continuity and ensure no short circuits between phases or to earth.
-
Apply safety checks — Before powering, confirm all covers are in place, tools are cleared, and you are wearing required safety gear.
-
Test the installation — Switch on briefly and observe the motor's startup. The resistance should be fully in at start, then progressively cut out as speed increases.
A 3-phase slip-ring motor has a rated rotor current of 50 A at full load. Without a rotor resistor, the starting current can reach 7 times the rated value (350 A), which would trip the supply.
Solution: By inserting a 0.5 Ω resistor in each rotor phase during startup:
Istart=RtotalVrotor
Assuming the induced rotor voltage at standstill is 200 V per phase, the starting current becomes:
Istart=0.5200=400 A
Wait — this calculation shows the current is still high. Actually, the rotor resistance starter works by limiting current and improving torque. In practice, the resistor value is chosen so that starting current is limited to about 2–3 times rated current, while torque increases significantly. For this 50 A motor, we select resistors to limit starting current to approximately 125 A (2.5 × rated), giving good starting torque without damaging the supply.
- Always disconnect power before making any connections
- Wear safety boots, goggles, gloves, and overalls when working
- Use insulated tools and ensure hands are dry
- Before testing, check that all covers are fitted and the work area is clear
- Never operate the motor with the resistor circuit open
In Tanzania, slip-ring motors with rotor resistance starters are commonly used in water pumping stations for irrigation, where high starting torque is needed to lift water from deep boreholes. A small-scale farmer in Morogoro using a 5 HP slip-ring pump can install a rotor resistance starter to ensure the motor starts smoothly without overloading the local solar battery system or grid supply, protecting both the equipment and the power source.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Interpret wiring diagram.
- Select tools, equipment and material
- Install the rotor resistance starter.
- Terminate cables.
- Test the rotor resistance starter.
- Observe safety precautions
- Clean the work place.
- Store tools, equipment and safety gear.
Tathmini ya matokeo
Rotor resistance starter for slip-ring motor is installed as per standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to:
- Install rotor resistance starter for slip-ring motor.
- Install three phase machine control.
Principles: The students should explain the principles of operating wound rotor induction motor.
Theories: The students should explain:
- Concept of slip ring.
- Production of magnetic flux in wound rotor induction Motor.
- Preventive maintenance of wound rotor induction motor.
- The application of wound rotor induction motor.
Swali
What is the main purpose of adding external resistance to the rotor circuit of a slip-ring motor during startup?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado