Mada za sehemu hiiPerforming PLC programmingMada 5
- Installing PLC software
- Performing basic sequence programming circuits
- Performing PLC ladder logic programmes
- Connecting input and output devices to PLC
- Performing simulation and factory automation
Connecting Input and Output Devices to PLC
A programmable logic controller (PLC) is the brain of an electronic control system. To function, it must receive information from input devices (like sensors and switches) and send commands to output devices (like lights and motors). This topic teaches you how to correctly connect these devices to a PLC so the system can monitor and control equipment.
Input devices provide signals to the PLC about the state of the system. The PLC reads these signals to decide what action to take.
Common Types of Input Devices
- Pushbutton (NO and NC): A manual switch that sends a signal when pressed. Normally Open (NO) contacts close when pressed; Normally Closed (NC) contacts open when pressed.
- Limit Switch: Detects the presence or absence of an object, often used on doors, gates, or moving machinery.
- Proximity Sensor: Detects nearby objects without physical contact, using infrared or electromagnetic fields.
- Temperature Sensor: Sends a signal when temperature reaches a set point.
- Pressure Switch: Sends a signal when pressure exceeds or drops below a threshold.
Role in PLC Systems
Input devices tell the PLC what is happening in the system. For example, a pushbutton tells the PLC "someone wants the machine to start," and a proximity sensor tells the PLC "an object is now in position."
Output devices perform actions based on commands from the PLC.
Common Types of Output Devices
- Indicator Light (Lamp): Visual signal showing the status of a system (green for running, red for stop).
- Solenoid Valve: Controls the flow of air, water, or oil in pneumatic or hydraulic systems.
- Contactor (Motor Starter): Switches an electric motor on or off.
- Buzzer or Alarm: Audible signal for warnings or alerts.
- Relay Output: Controls another electrical circuit.
Role in PLC Systems
Output devices carry out the PLC's decisions. When the PLC receives the correct input signals, it energizes the appropriate output to perform an action, such as turning on a light or starting a motor.
A typical PLC has clearly marked terminals for wiring inputs and outputs. Understanding the layout is essential for correct connection.
Input Side (Common Features)
- Terminals labeled "I" or "X": Each input point (I0, I1, I2, etc.) connects to one input device.
- COM (Common) Terminal: All input devices share a common return path, typically connected to the negative (-) of the power supply.
- Power Supply Connection: Inputs require a 24V DC supply in most trainer PLCs.
Output Side (Common Features)
- Terminals labeled "Q" or "Y": Each output point (Q0, Q1, Q2, etc.) connects to one output device.
- COM (Common) Terminal: Output devices share a common line, usually connected to the live (L) or positive of the load power supply.
- Separate Power Source: Outputs often use a different voltage (e.g., 230V AC for lights) from the PLC's internal 24V DC.
Visual Layout Example
+24V ----[Input Device]---- I0 ----+---- COM
|
(PLC)
Q0 ----[Output Device]---- COM ---- 230V Live
Following proper wiring procedures ensures safety, reliability, and ease of troubleshooting.
General Guidelines
- Switch off power before making any connections.
- Use correct wire sizes — typically 0.75 mm² to 1.5 mm² for PLC wiring.
- Strip wires cleanly — remove 6–8 mm of insulation without damaging the conductor.
- Tighten terminal screws firmly — loose connections cause intermittent operation.
- Dress wires neatly — run cables in organized paths to avoid confusion during maintenance.
- Label all wires — use tags or markers to identify each connection.
- Check polarity — ensure positive and negative are connected correctly for DC circuits.
Safety Precautions
- Always wear safety goggles and gloves when working with electrical equipment.
- Use insulated tools.
- Verify that all circuits are de-energized using a multimeter before touching wires.
In this practical example, we will connect a normally open (NO) pushbutton as an input and an indicator lamp as an output.
Equipment Required
- PLC (with 24V DC input power)
- Normally open pushbutton (input device)
- Indicator lamp (output device)
- Connecting wires
- Power supply (24V DC for PLC, 230V AC or 24V DC for lamp)
- Screwdriver and multimeter
Connection Steps
Step 1: Connect the Input (Pushbutton)
- Connect one terminal of the 24V DC positive (+) to one side of the pushbutton.
- Connect the other side of the pushbutton to input terminal I0 on the PLC.
- Connect the COM terminal on the PLC input side to the 24V DC negative (-).
Step 2: Connect the Output (Indicator Lamp)
- Connect one terminal of the lamp to output terminal Q0 on the PLC.
- Connect the other terminal of the lamp to the COM terminal on the output side.
- Connect the output COM to the live supply (e.g., 230V AC) through a fuse or protective device.
- Connect the lamp's other terminal to the neutral of the supply.
Step 3: Verify and Test
- Double-check all connections match the diagram.
- Switch on the power supply.
- Program the PLC so that when I0 is pressed (ON), Q0 turns ON (lamp lights up).
- Press the pushbutton — the lamp should illuminate. Release — the lamp should turn off.
Wiring Diagram
+24V
|
[Pushbutton NO]
|
+---- I0 (PLC Input)
|
COM -------- -24V
Q0 (PLC Output) ----[Indicator Lamp]---- COM ---- 230V Live
|
Neutral
In Tanzania, this skill is used when installing solar-powered water pumping systems in rural areas. For example, a technician may connect a float switch (input) to a PLC to detect when a water tank is full, and then wire a pump (output) to automatically stop filling. The same principle is applied in small agro-processing machines at local markets in Arusha or Dar es Salaam, where pushbuttons and indicator lights are wired to PLCs to control grain milling machines safely and efficiently.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Select tools, equipment and safety gear
- Interpret circuit diagram
- Prepare input and output device
- Connect input and output device to PLC
- Observe safety precautions
- Clean tools, equipment and work area
- Store tools, equipment and safety gear.
Tathmini ya matokeo
An input and output device is connected to PLC as per technical specifications and Regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to:
- Set up a PLC trainer
- Connect input and output devices to PLC
- Download PLC programming software
Principles: The students should explain the principles of:
- PLC Programming.
- HMI programming
Theories: The students should explain
- Combination logic
- Sequential logic
- Connection between PLC and HMI.
- Ladder logic
Swali
What is the primary function of input devices in a PLC system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado