Mada za sehemu hiiPerforming threadingMada 2
- Performing tapping
- Performing die cutting
Die cutting is a manual method of making external threads on the outside surface of a rod or pipe using a tool called a die. An external thread is a spiral-like groove cut around a rod, similar to the thread on a bolt. The die is held in a die stock (die holder) and is turned onto the rod to cut the thread.
External threads are useful for:
- Joining two parts together (like a bolt and nut)
- Transmitting motion in mechanical systems
- Making mechanical adjustments
- Die: A hardened steel tool with cutting edges that forms the external thread
- Die stock: A handle used to hold and turn the die
- Workpiece: A metal rod of appropriate diameter
- Centre punch: To mark starting point
- Hammer: To strike centre punch
- Cutting oil: To lubricate during cutting
- Bench vice: To hold the workpiece steady
- Vernier caliper: To measure thread diameter

- Round die (solid die): Common type used for general thread cutting
- Adjustable die: Can be adjusted to cut different thread sizes
- Split die: Can be adjusted and is easier to start
Step 1: Prepare the Workpiece
- Select a rod of the correct diameter for the thread size you want to cut
- Measure and mark the length of the thread to be cut using a steel ruler
- Use a centre punch to make a small dent at the starting point of the thread
Step 2: Secure the Workpiece
- Clamp the workpiece firmly in a bench vice
- Make sure it is held at a convenient height for cutting
- Ensure the rod is vertical or horizontal, depending on the setup
Step 3: Prepare the Die
- Select the correct die for the thread size (for example, M6 die for M6 thread)
- Fit the die into the die stock and tighten securely
Step 4: Start Die Cutting
- Apply cutting oil to the rod where the thread will be cut
- Position the die squarely on the end of the rod
- Turn the die clockwise while applying steady downward pressure
- Make 2-3 initial turns, then turn back slightly (about half a turn) to break the chips
- Continue turning forward, applying cutting oil regularly
Step 5: Complete the Thread
- Continue cutting until the desired thread length is achieved
- Turn the die counterclockwise to remove it from the workpiece
- Check the thread quality by trying to thread a nut onto it
Step 6: Clean Up
- Remove any burrs or sharp edges
- Clean the workpiece and tools
- Store tools in their proper places
- Wear safety glasses to protect eyes from flying metal chips
- Wear safety boots and gloves
- Ensure workpiece is firmly secured in the vice
- Apply cutting oil to reduce friction and heat
- Do not apply excessive pressure on the die
- Turn the die slowly and steadily
- Keep fingers away from the cutting edges
A student needs to cut an M6 external thread on a rod. The rod diameter should be approximately 6mm. The student:
- Selects a 6mm diameter mild steel rod
- Marks 20mm length for the thread using a steel ruler
- Makes a centre punch mark at the starting point
- Secures the rod in a bench vice
- Selects an M6 die and fits it into the die stock
- Applies cutting oil to the marked area
- Starts turning the die clockwise while applying light pressure
- Turns back after every 2-3 turns to break chips
- Continues until 20mm of thread is cut
- Removes the die and checks the thread with an M6 nut
The thread is successful if the nut fits smoothly onto the rod.
| Problem | Possible Cause | Solution |
|---|---|---|
| Thread is rough | Die not started squarely | Start die at right angle to rod |
| Thread is incomplete | Insufficient cutting pressure | Apply more downward pressure |
| Die sticks to workpiece | Not using cutting oil | Apply cutting oil regularly |
| Thread is oversized | Rod diameter too large | Use correct diameter rod |
In Tanzania, die cutting is used by electricians and solar panel installers when installing conduit systems. For example, when mounting a solar home system, an electrician may need to cut external threads on metal conduits to connect junction boxes or attach fittings. This skill is also used by motor rewinding technicians in towns like Arusha and Mwanza when repairing electric motors that require threaded shafts or bolts for reassembly.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Interpret the drawing.
- Prepare the blanks.
- Undertake die cutting.
- Perform die cutting
- Clean the workplace/workpiece.
- Store the work place, work pieces and tools.
Tathmini ya matokeo
Die cutting is performed as per specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to perform die cutting Principle: The students should be able to Understand the significance of following safety protocols to prevent accidents and injuries during die cutting.
Theories: The students should explain:
- Types of die cutting.
- Materials for the manufacture of dies.
- The importance of applying oils when threading.
- Pressure and cutting forces
- Steps for die cutting
Swali
What is the hand method of cutting an external thread on a rod called?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado