Mada za sehemu hiiPerforming cold electrical jointsMada 7
Making Bolt Joint
A bolt joint is a type of cold electrical joint used to connect two or more electrical conductors together using a bolt, washer, and nut. This joint is commonly used in solar power installations where reliable, permanent connections are needed between cables and terminals.
Selecting the correct size bolt and terminal for your cable is essential for several reasons:
- Electrical continuity — A loose or undersized connection increases resistance, causing heat buildup and energy loss
- Mechanical strength — An undersized bolt may break under tension or vibration
- Safety — Poor connections can lead to sparks, fires, or equipment damage
- Longevity — Proper sizing prevents corrosion and deterioration of the joint
When the bolt is too small for the cable gauge, the conductor strands may not be properly compressed, leading to a weak and unreliable connection.
Before starting, ensure you have:
- Tools: diagonal cutting pliers, combination pliers, electrician knife, measuring tape, long nose pliers, multimeter
- Materials: cables, eyelet terminals, bolts, washers, nuts
- Safety gear: safety goggles, safety boots, overall, work bench
Always wear your safety gear before beginning any electrical work.
Step 1: Prepare the Cable
- Measure and cut the cable to the required length using diagonal cutting pliers.
- Strip the insulation from the cable end using the electrician knife — typically 15–20 mm of conductor should be exposed.
- Twist the stranded wires together neatly to form a tight, compact end.
Step 2: Prepare the Eyelet Terminal
- Select an eyelet terminal that matches the cable size and the bolt diameter.
- Insert the bared conductor into the eyelet terminal barrel.
- Crimp the barrel firmly using combination pliers to create a secure mechanical and electrical connection.
Step 3: Assemble the Bolt Joint
- Place a flat washer onto the bolt.
- Pass the bolt through the eyelet terminal hole.
- Add another flat washer on the opposite side.
- Screw the nut onto the bolt and tighten firmly using combination pliers or a spanner.
Step 4: Test the Connection
- Use the multimeter to check for continuity across the joint — there should be no resistance reading.
- Inspect the joint to ensure all strands are contained and no copper is exposed.
- Verify the connection is tight and secure.
A student is installing a 6 mm² solar cable from a panel to a charge controller. The cable requires connection to a 6 mm² eyelet terminal using an M6 bolt.
Procedure:
- Strip 18 mm of insulation from the cable end.
- Insert the bared 6 mm² conductor into a 6 mm² eyelet terminal and crimp firmly.
- Slide the eyelet onto an M6 bolt with a washer on each side.
- Tighten the M6 nut securely.
- Test with multimeter — continuity is confirmed (0.0 Ω reading).
This creates a strong, low-resistance connection suitable for the solar installation.
- Always wear safety goggles, boots, and overalls when handling tools
- Ensure the work bench is clear and stable
- Never work on live circuits — disconnect power before making joints
- Check all connections are tight before restoring power
In many rural Tanzanian villages, solar home systems are becoming common. When installing a 100W solar panel system, technicians use bolt joints to connect the panel cables to the charge controller and battery terminals. For example, a technician in Mwanza might use a properly sized bolt joint to connect a 4 mm² cable from a solar panel to a 12V battery, ensuring the system runs efficiently without losing power through loose or corroded connections — which is especially important when every ampere counts for lighting a home at night.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Select tools, equipment and materials required.
- Prepare cables for termination.
- Make cable joints.
- Test joints.
- Observe safety precautions
- Clean work area.
- Store tools, equipment and remained materials.
Tathmini ya matokeo
Bolt joint is made as per IET regulation.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students would be able to explain how to: Make bolt joint.
Method used: The students should explain how to:
- Prepare cables for jointing.
- Execute particular joints
Principles: The students should explain how to Making bolt joint. Theory: the students should explain how to:
- Make bolt joint
- IET regulation about Making Make bolt joint
Swali
What is a bolt joint in solar power installation?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado