Mada za sehemu hiiConstructing RLC circuitMada 3
- Building a resistor and capacitor (RC) circuit
- Building a resistor and inductor (RL) circuit
- Building a resistor, capacitor and inductor (RLC) circuit
Resistor and Inductor (RL) Circuit
An RL circuit is a simple electrical circuit that contains a resistor (R) and an inductor (L) connected together. These circuits are very important in solar power systems and many everyday electrical devices. In this topic, you will learn how to build and understand how resistors and inductors work together in a circuit.
A resistor is a component that limits or controls the flow of electric current in a circuit. It provides resistance, measured in Ohms (Ω).
- Resistors are used to protect sensitive components from too much current
- They help divide voltage in a circuit
- They come in different values (e.g., 100Ω, 220Ω, 1kΩ)
An inductor is a coil of wire that stores energy in a magnetic field when electric current flows through it. It provides inductance, measured in Henrys (H).
- Inductors resist changes in current flow
- They are used in filters, transformers, and energy storage
- In solar power systems, inductors help smooth out power from solar panels
Series RL Circuit
The resistor and inductor are connected one after another in a single path:
Battery → Resistor → Inductor → Battery
Parallel RL Circuit
The resistor and inductor are connected across the same two points:
┌───── Resistor ─────┐
│ │
Battery Battery
│ │
└───── Inductor ─────┘
Follow these steps to build a simple series RL circuit:
-
Gather your materials: Resistor, inductor coil, connecting wires, battery or power supply, multimeter, and safety gear (overall, safety goggles, safety boots).
-
Plan your circuit: Draw the circuit diagram first. Decide whether you will build a series or parallel circuit.
-
Prepare the wires: Use the electrician knife to strip the insulation from the ends of your connecting wires if needed.
-
Connect the resistor: Use combination pliers to connect one end of the resistor to a wire.
-
Connect the inductor: Connect the inductor in series with the resistor (or in parallel if required).
-
Connect to power: Finally, connect the circuit to your battery or power supply.
-
Measure with multimeter:
- Set the multimeter to measure DC voltage or resistance as needed
- Connect the probes to measure voltage across components
- Record your readings
-
Observe and record: Note how the current behaves with both components in the circuit.
Problem: A series RL circuit contains a resistor of 100Ω and an inductor with negligible resistance. If a 12V battery is connected, calculate the current flowing through the circuit.
Solution:
In a series circuit with only the resistor providing opposition to DC current (the inductor DC resistance is negligible):
I=RV
I=100Ω12V=0.12A
So the current flowing through the circuit is 0.12 Amperes (or 120 milliamps).
When building RL circuits, always follow these safety rules:
- Wear your overall and safety goggles at all times
- Wear safety boots to protect your feet
- Always disconnect power before making or changing connections
- Use tools properly — combination pliers, diagonal cutting pliers, and long nose pliers for their intended purposes
- Keep your work area clean and organized on your workbench
- Never touch bare wires while the circuit is connected to power
- Use the measuring tape to ensure proper spacing and organization
You will use the multimeter to measure:
- Voltage across the resistor and inductor
- Current flowing through the series circuit
- Resistance of the resistor when the circuit is powered off
Remember: Always set your multimeter to the correct measurement type (DC voltage, AC voltage, or resistance) before measuring.
RL circuits are used in many practical applications:
- Filtering: In solar power inverters, RL circuits help filter electrical noise
- Energy storage: Inductors store energy temporarily in magnetic fields
- Timing circuits: The behavior of current rise and fall in RL circuits creates time delays useful in electronic controls
In Tanzania, RL circuits are used in solar power installations found in many rural villages and towns like Singida, Mbeya, and Morogoro. When installing solar panels, technicians use resistors and inductors in the inverter system to control and smooth the electricity flowing from the panels to homes and businesses. A small solar system with a 100W panel might use an RL circuit to ensure safe 12V DC power that can charge phones or run small LED lights, helping families who rely on solar energy for lighting after sunset.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Design a wiring diagram of the RL circuit.
- Select tools, equipment and materials required.
- Prepare inductors, resistor and cable for termination.
- Build RL circuit.
- Solder the built circuits.
- Measure and record the RL parameters of the circuit.
- Observe safety precautions.
- Clean the work area, tools and equipment.
- Store tools, equipment and the remaining materials.
Tathmini ya matokeo
The resistor and inductor (RL) circuit is built as per IET regulation
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to build a resistor and inductor (RL) circuit
Principles: The students should explain how to:
- Construct RL circuit.
- Carry out measurements in an RL circuit.
Theories: The students should explain:
- Connection of RL circuit
- Calculation of impedance
- Calculation of voltage and current
Swali
What is the main function of a resistor in an RL circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado