Mada za sehemu hiiMeasuring electric quantitiesMada 3
- Measuring voltage in the circuit
- Measuring current in the circuit
- Measuring resistance in the circuit
Voltage is the "push" that makes electric current flow through a circuit. To measure this push, we use a tool called a voltmeter or the voltage setting on a multimeter.
Voltage is the difference in electric potential energy between two points in a circuit. Think of it like water pressure in a pipe — the higher the pressure, the stronger the push of water through the pipe. In electricity, voltage is the push that forces electrons to move from one point to another through a conductor.
Water Analogy for Voltage
Imagine a water tank placed high above a pipe. The water inside the tank has gravitational potential energy because of its height. When we open a pipe connected to the tank, water flows downward due to this pressure. The height of the water determines how strong the flow will be.
In an electric circuit:
- The water tank is like a voltage source (such as a solar panel or battery)
- The water pressure is like voltage (measured in Volts, symbol V)
- The flowing water is like current (measured in Amperes, symbol A)
Just as higher water pressure pushes more water through a pipe, a higher voltage pushes more electric charge through a circuit.
In a Series Circuit
When components are connected one after another in a single path, the voltage is shared among them. The total voltage across all components equals the source voltage:
Vtotal=V1+V2+V3
In a Parallel Circuit
When components are connected across the same two points, each component receives the full source voltage. The voltage across each parallel branch is the same as the source voltage:
Vbranch=Vsource
- Turn on the multimeter and select the DC voltage (V⎓) or AC voltage (V~) setting, depending on your power source.
- Identify the positive and negative terminals of the voltage source or component you want to measure.
- Connect the test leads: Insert the red lead into the VΩmA port and the black lead into the COM (common) port.
- Place the probes: Touch the red probe to the positive side and the black probe to the negative side of the component or circuit.
- Read the display: The multimeter will show the voltage value in Volts (V). If you get a negative reading, swap the probes.
- Record your measurement and turn off the multimeter when finished.
Important Safety Tips
- Always set the multimeter to the correct voltage range. Start with the highest range and decrease if needed.
- Never measure voltage while touching bare wires with your hands.
- Wear plastic gloves and safety boots when working with live circuits.
A student builds a simple series circuit using a 9V battery and two resistors connected in series: R₁ = 2Ω and R₂ = 4Ω. The student measures the voltage across each resistor using a multimeter.
Given: Source voltage Vsource=9 V
Find: Voltage across R₁ and R₂
Solution:
In a series circuit, the total resistance is:
Rtotal=R1+R2=2Ω+4Ω=6Ω
Using Ohm's Law (V=IR), the current in the circuit is:
I=RV=6Ω9 V=1.5 A
Now calculate voltage across each resistor:
- Voltage across R₁: V1=I×R1=1.5 A×2Ω=3 V
- Voltage across R₂: V2=I×R2=1.5 A×4Ω=6 V
Check: V1+V2=3 V+6 V=9 V (equals the source voltage)
When the student connects the multimeter across R₁, it should read 3V. Across R₂, it should read 6V. Across both resistors together, it should read 9V — the same as the battery voltage.
In Tanzania, voltage measurement is used when installing solar home systems. For example, a technician checks that a 12V solar panel is producing the correct voltage before connecting it to a charge controller and battery. If the panel reads below 12V in full sunlight, the technician knows it may be damaged or not receiving enough solar energy, similar to checking that a water pump at a farm produces enough pressure to push water through irrigation pipes.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Select tools and equipment
- Determine component values.
- Connect simple electric circuits.
- Measure voltage.
- Observe safety precautions.
- Clean workplace.
- Store tools and equipment.
Tathmini ya matokeo
voltage in a circuit is measured as per IET regulation
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to measure voltage in the circuit.
Principles: The students should explain how to: measure voltage in the circuit
Theories: The students should explain:
- Ohm’s law.
- Voltmeter operation
- Scale extension of voltmeter scale
- Connection of voltmeter
- Range selection
Swali
What does voltage represent in an electric circuit, according to the water analogy?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado