Mada za sehemu hiiDetermining characteristics of active electronic componentsMada 3
- Testing characteristics of diodes
- Testing characteristics of transistors
- Testing characteristics of thyristor
Testing Characteristics of Transistors
A transistor is a small electronic component that can control the flow of electric current. It acts like a switch or an amplifier in circuits. In this lesson, you will learn how to test whether a transistor is working properly using a digital multimeter.
A transistor is an active electronic component made of semiconductor material (usually silicon). It has three terminals:
- Base (B) – the control terminal
- Collector (C) – the input terminal
- Emitter (E) – the output terminal
Transistors are used in many devices, including radios, televisions, phone chargers, and solar power systems. They can either switch current on and off (like a switch) or amplify weak signals (like in audio equipment).
The two most common types are:
- NPN Transistor – current flows from Collector to Emitter when the Base receives a small current.
- PNP Transistor – current flows from Emitter to Collector when the Base receives a small current.
Both types work the same way, but the current direction is opposite.
A digital multimeter can check if a transistor's junctions are working correctly. A good transistor should show specific resistance values between its terminals.
Steps for Testing an NPN Transistor
- Turn off power – Make sure the circuit is disconnected from any power source.
- Set the multimeter – Turn the dial to the diode testing mode (usually marked with a diode symbol or "∇").
- Identify the terminals – Locate the Base, Collector, and Emitter of the transistor. Refer to the component's datasheet or marking if unsure.
- Test the Base-Collector junction:
- Place the red (positive) probe on the Base.
- Place the black (negative) probe on the Collector.
- A good NPN transistor will show a voltage drop between 0.5V and 0.8V.
- Test the Base-Emitter junction:
- Keep the red probe on the Base.
- Move the black probe to the Emitter.
- A good transistor will show a similar voltage drop (0.5V to 0.8V).
- Test the Collector-Emitter path:
- Reverse the probes (red on Collector, black on Emitter).
- The multimeter should display "1" or OL (open loop), meaning no current flows in this direction.
Steps for Testing a PNP Transistor
For a PNP transistor, the readings are opposite:
- When the black probe is on the Base and the red probe is on the Collector or Emitter, you should get a voltage drop (0.5V to 0.8V).
- When the probes are reversed, you should get "1" or OL.
Interpreting Results
| Test | Good Transistor | Faulty Transistor |
|---|---|---|
| Base-Collector | 0.5V – 0.8V | 0V (short) or OL (open) |
| Base-Emitter | 0.5V – 0.8V | 0V (short) or OL (open) |
| Collector-Emitter | OL (no reading) | Any voltage reading (leaking) |
A student tests an NPN transistor (type 2N2222) using a digital multimeter set to diode mode. The readings are:
- Base to Collector: 0.68V
- Base to Emitter: 0.65V
- Collector to Emitter: OL
Analysis:
- The Base-Collector junction shows 0.68V → within the normal range (0.5V–0.8V) ✓
- The Base-Emitter junction shows 0.65V → within the normal range ✓
- The Collector-Emitter path shows OL → no current flows, as expected ✓
Conclusion: The transistor is working correctly and can be used in a circuit.
- Always disconnect power before testing components.
- Wear safety goggles when working with electronic equipment.
- Handle transistors carefully—they are sensitive to static electricity.
- Keep the workbench clean and organized.
In Tanzania, transistors are found in many everyday devices such as phone chargers, solar lighting systems, and radio receivers. When a solar charger stops working, a technician can use a multimeter to test the transistor inside the charging circuit. If the transistor shows 0V or OL at the Base-Collector junction, the technician knows the transistor is faulty and must replace it. This skill helps small electronics repair businesses in towns like Arusha or Mwanza fix devices quickly, saving customers money instead of buying new equipment.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Select tools, equipment, safety gear and components
- Construct circuit
- Connect test equipment
- Perform component characteristics test
- Record test results
- Observe safety measures
- Clean workplace
- Store tools, equipment, safety gear and components
Tathmini ya matokeo
characteristics of transistors are tested as per IET regulation
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to test the characteristics of transistors
Principles: The students should explain how to:
- Construct the transistor.
- Carry out measurement
Theories: The students should explain: -
- The PNP/NPN formation
- Terminal identification
- Biasing of the transistor
- Application of the transistor
Swali
What are the three terminals of a transistor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado