Mada za sehemu hiiCarrying out earthing systemsMada 4
- Performing TT earthing methods
- Performing IT earthing methods
- Performing TNS earthing methods
- Performing bonding of metal fixtures
Understanding TT Earthing Systems
TT earthing is a method of connecting the electrical installation to the earth using a dedicated earth electrode that is driven directly into the ground. In this system, the consumer's earth electrode is completely separate from the supply company's earth connection. The letters "TT" stand for: the first "T" means the consumer has a direct connection to earth (Terra in Latin), and the second "T" means the supply system also has its own earth connection.
The main purposes of TT earthing in household or commercial electrical systems include:
- Safety: It provides a path for fault current to flow safely to the ground, ensuring protective devices (like circuit breakers) trip quickly when a fault occurs
- Protection against electric shock: If a live wire touches the metal casing of an appliance, the earth connection ensures the casing does not become dangerous to touch
- Voltage stabilization: It helps maintain stable voltage levels in the electrical system
- Lightning protection: It provides a path for lightning surge currents to dissipate into the earth
- Reducing electrical noise: It helps minimize electromagnetic interference in sensitive electronic equipment
A typical TT earthing system consists of the following components:
- Earth electrode: A metal rod (usually copper or galvanized steel) driven into the ground
- Earth lead: A conductor that connects the earth electrode to the main earthing terminal
- Main earthing terminal: A bar or block where all earth connections are made
- Earth continuity conductor: The green and yellow (or green) wire that connects appliances to the earthing system
- Earth clamp: A fitting that securely connects the earth lead to the electrode
- Soil: The surrounding earth that provides the electrical contact
The diagram below shows how a TT earthing system is arranged in a typical household:
Supply Pole
|
[Supply Earth]
|
----------------
| |
[Consumer] [Consumer]
Earth Rod Earth Rod
| |
[Main DB] ---- [Earthing Bar]
| |
[Lighting] [Sockets]
[Appliances] [Metal casings]
In this layout:
- The supply company provides its own earth connection at the supply point
- The consumer installs a separate earth electrode (earth rod) at the building
- The consumer's earth electrode is connected to the main distribution board (DB)
- All metal parts and appliances are connected to this earth bar through protective earth conductors
Step 1: Planning and Preparation
Before starting the installation, gather all required tools and materials:
- Earth electrode (copper or galvanized steel rod)
- Earth lead (green/yellow copper conductor)
- Earth clamp
- Spanners, screwdrivers
- Hoe and spade (for digging)
- Megger meter or continuity tester
- Ground resistance meter
- Safety boots, goggles, and gloves
Step 2: Selecting the Earth Electrode Location
Choose a suitable location for the earth electrode:
- Ideally near the main distribution board
- At least 1.5 meters from any building foundation
- In a moist area (moist soil has lower resistance)
- Away from underground pipes, cables, or gas lines
- The area should be accessible for testing and maintenance
Step 3: Installing the Earth Electrode
- Dig a hole or trench about 50-80 cm deep at the selected location
- Drive the earth rod vertically into the soil using a hammer or driving tool
- The rod should extend at least 1.2 meters below ground level
- If the soil is very dry, apply soil resistance reducing compound around the rod to improve conductivity
Step 4: Connecting the Earth Lead
- Strip the end of the earth lead (green/yellow conductor)
- Attach the earth lead to the earth electrode using an earth clamp
- Tighten the clamp securely using spanners
- Route the earth lead to the main earthing terminal (usually inside the main distribution board)
- Secure the earth lead along its route using clips or clamps
Step 5: Connecting to the Main Earthing Terminal
- At the main distribution board, connect the earth lead to the main earthing terminal bar
- Ensure all connections are tight and secure
- Connect the consumer unit's earth bar to this main earthing terminal
- Run earth continuity conductors from the earthing terminal to all socket outlets, switches, and metal fixtures
After installation, the system must be tested to ensure it works properly:
- Continuity test: Use a megger or continuity tester to verify that all earth connections are continuous from the electrode to every outlet
- Earth resistance test: Use a ground resistance meter to measure the earth electrode resistance. The value should be less than 20 ohms for TT systems (lower is better)
- Visual inspection: Check all connections are tight and no conductors are damaged
If the earth resistance is too high (above 20 ohms), you can improve it by:
- Driving the electrode deeper
- Adding more electrodes in parallel
- Treating the soil with moisture or salt
- Using soil resistance reducing compounds
When working on TT earthing systems, always observe these safety practices:
- Wear safety boots, goggles, and plastic gloves
- Ensure the electrical supply is switched off before working on the installation
- Use insulated tools
- Never work alone; have someone nearby in case of emergency
- Check for underground services before digging
- Ensure all connections are tight to avoid loose contacts that can cause heating or fires
A student needs to wire a single 13A socket outlet using the TT earthing system. The socket has three terminals: Live (L), Neutral (N), and Earth (E).
Steps:
- Connect the brown (or red) Live wire to the L terminal
- Connect the blue (or black) Neutral wire to the N terminal
- Connect the green/yellow Earth wire to the E terminal
- The Earth wire runs from the socket E terminal back to the main earthing bar in the distribution board
- From the main earthing bar, another green/yellow conductor connects to the earth electrode driven into the ground outside the building
When a fault occurs (for example, the Live wire touches the metal socket face), the fault current flows through the Earth wire to the earth electrode and into the surrounding soil. This high fault current quickly causes the circuit breaker to trip, disconnecting the power and preventing electric shock.
In Tanzania, TT earthing is commonly used in homes, schools, and small businesses that rely on solar power systems. For example, when installing a 3kW solar panel system on a house in Dar es Salaam, proper TT earthing protects the metal mounting frame and inverters from lightning strikes and fault currents. A properly installed earth electrode with resistance below 20 ohms ensures that if lightning hits the panels, the surge safely flows into the ground rather than damaging expensive appliances inside the house or causing a fire.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Select tools, equipment and safety gear
- Draw wiring diagrams.
- Identify the earthing electrodes.
- Install the TT earthing systems.
- Test the function of TT earthing.
- Observe safety precautions.
- Clean the workplace, tools and equipment.
- Store tools, equipment and remaining materials.
Tathmini ya matokeo
TT earthing systems is performed as per IET regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to perform TT earthing methods.
Principles: The students should explain how to:
- Perform Earthing.
- Measure earth resistance
Theories: The students should explain:
- Measurement of earth resistance.
- Allowable earth resistance
- Reducing earth resistance
- Earth continuity conductor
- Earth led
- Earth
- Connection diagram of earthing systems
- Meaning of TT
- Application of TT
- electrode
- IET regulations
Swali
What does the first "T" in TT earthing represent?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado