Mada za sehemu hiiInstalling protective devicesMada 3
- Installing three phase over-current protective devices
- Installing three phase earth leakage protective devices
- Installing over-voltage and under voltage protective devices
Over-voltage and under-voltage protective devices are electrical safety devices that disconnect power supply when voltage levels become too high or too low, protecting equipment from damage.
Electrical equipment is designed to operate within specific voltage limits. When the voltage rises above the safe limit (over-voltage) or falls below the safe limit (under-voltage), the equipment can be damaged.
Over-voltage refers to voltage that exceeds the normal operating level. It is mainly caused by:
- Lightning strikes
- Switching operations in the power grid
Under-voltage refers to voltage that drops below the normal level. It is mainly caused by:
- Overloads in the electrical system
- Short-circuit faults
These protective devices monitor voltage levels continuously and automatically disconnect the power supply when voltage goes outside safe limits, preventing equipment damage and hazards such as insulation failure and overheating.
The following are the common types of over-voltage protection devices:
Surge arresters (over-voltage protectors)
Surge arresters are designed to protect equipment from transient over-voltages, such as those caused by lightning strikes or switching surges. They provide a path for excess voltage to flow to ground, protecting the connected equipment.
Surge protection devices (SPDs)
Surge protection devices are similar to surge arresters but are often used for specific applications, such as protecting sensitive electronic equipment like computers and televisions.
Over-voltage relays
Over-voltage relays monitor voltage levels in a circuit and automatically disconnect the power supply when the voltage exceeds a predetermined threshold. They are commonly used in industrial and commercial installations.
Under-voltage protective devices safeguard electrical equipment from damage caused by abnormally low voltage levels. They disconnect the equipment when voltage drops below a predetermined threshold.
Detection of under-voltage conditions is normally performed using undervoltage relays. These relays trigger the tripping of circuit breakers if voltage level dips below a pre-set value.
Undervoltage relays are categorized into three types:
| Type | Description |
|---|---|
| Electromechanical relays | Use magnetic fields to operate; less common in modern systems |
| Static relays | Use solid-state electronic components for faster operation; preferred over electromechanical relays |
| Digital relays | Use microprocessors to analyse signals and respond to voltage conditions; offer high programmability, accuracy and reliability |
Before installing over-voltage or under-voltage protective devices, always follow these safety measures:
- Wear appropriate PPE (personal protective equipment) including insulated gloves, safety boots, safety goggles, and overalls
- Switch OFF the main power supply before starting installation
- Use lockout/tag-out procedures to prevent the circuit from turning ON accidentally
- Ensure the working area is clean and free from hazards
- Use insulated tools
- Verify the circuit is de-energized using a voltage tester before touching any conductors
The following steps outline how to install over-voltage and under-voltage protective devices:
-
Wear appropriate PPE before starting any work.
-
Study the wiring diagram provided by your teacher to understand all components and the connection layout.
-
Gather all required tools and materials, including spanners, screwdrivers, multimeter, voltage tester, wire strippers, combination pliers, and the protective devices.
-
Switch OFF the main supply and use a voltage tester to confirm that the circuit is dead.
-
Identify the load or equipment that needs protection from voltage fluctuations.
-
Select the correct devices according to voltage ratings and equipment requirements.
-
Mark and prepare the mounting positions for the devices on the installation board or distribution board.
-
Mount the device securely, ensuring it is properly aligned.
-
Perform wiring according to the given wiring diagram and manufacturer instructions. Connect all phase conductors, neutral, and earth wires correctly.
-
Check for loose connections and label all wires for easy identification.
-
Request your teacher to inspect the circuit before powering it ON.
-
After approval, switch ON the supply and test the protective devices to ensure they operate correctly under simulated voltage fault conditions.
-
Clean the working area and store tools and materials properly.
A small solar power system in a Tanzanian home has a 230V rating for its inverter and battery charging equipment. The homeowner wants to protect this equipment from voltage fluctuations.
Solution:
The installer should:
-
Select an over-voltage protective device set at a threshold slightly above 230V (typically 250V-260V for protection)
-
Select an under-voltage protective device set at a threshold slightly below 230V (typically 180V-200V to prevent deep discharge damage)
-
Install both devices between the main distribution board and the solar inverter circuit
-
Connect the devices in series with the line conductor, ensuring proper grounding for the over-voltage protector
This ensures that when voltage rises above 260V or drops below 180V, the power to the solar equipment is automatically disconnected, protecting the expensive inverter and batteries from damage.
In Tanzania, many small businesses and households use solar power systems to reduce electricity costs from TANESCO. For example, a small shop in Arusha with a solar PV system protecting a refrigerator and lighting needs over-voltage protection to prevent damage from voltage surges during thunderstorms, which are common during the rainy season. Installing these protective devices ensures the refrigerator stays working, preventing food spoilage worth thousands of Tanzanian shillings.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Select tools, equipment and materials required.
- Interpret single line and lay out drawings.
- Install overvoltage and under voltage protective devices
- Observe safety precautions
- Clean the work area.
- Store tools, equipment and safety gear.
Tathmini ya matokeo
Over-voltage and under voltage protective devices installed as per IET regulations
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to install over-voltage and under voltage protective devices
Principles: The students should follow the correct procedures how to install over-voltage and under voltage protective devices
Theories: The students should explain:
- Operation of over-voltage and under voltage protective devices
- IET regulation
Swali
What is the primary function of over-voltage and under-voltage protective devices?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado