Mada za sehemu hiiMaking casual garments using readymade and commercial patternsMada 7
- Making blouses with sleeves [kimono, set in sleeves, raglan flat collar]
- Making a skirt with hooks and eyes, zip fastener, buttons/loops, darts, gathering, belts and belt carriers, edge finishing and pocket set in seam
- Making short-sleeved shirts [patch pocket with flaps, button, and buttonholes, press studs, stand collars and easing]
- Making dresses [continuous wrap opening, faced opening, bound opening, bias binding/crossway strips, tapes and ribbons, press studs and shirring]
- Making knickers [overlaid seam, inseam pocket and elasticated waist]
- Making pajamas [machine fell/run and fell seam and elasticated waist]
- Making shorts [welt pocket with flap, belt and belt carrier, double stitched seam, Velcro fastener, zip fastener, hook and eye and tucks]
Making Short-Sleeved Shirts
A short-sleeved shirt is a casual garment that can be made with various features including patch pockets with flaps, button and buttonhole closures, press studs, and stand collars. This study note will guide you through the process of drafting patterns and constructing a short-sleeved shirt using commercial or readymade patterns.
Before drafting or cutting a shirt pattern, you need to take the following measurements from the person who will wear the garment:
- Full length – measure from shoulder to the desired hemline
- Shoulders width – measure across the shoulders from end to end
- Breast-girth – measure around the fullest part of the chest
- Seat-girth – measure around the widest part of the hips
- Neck girth – measure around the base of the neck
- Sleeve length – measure from shoulder to the desired sleeve end
- Sleeve width – measure around the fullest part of the upper arm
The back part of the shirt forms the foundation of the garment. Follow these steps to draft the back pattern:
- Draw a squared line starting at point A-B-C.
- A-C = half shoulders plus 1¼ cm (½") for seam allowance.
- A-D = 4¼ cm (1¾"). Square out line D-E.
- D-F = ⅙ neck-girth.
- E-H = shoulder slope, measuring 2.5 cm to 5 cm (1" to 2") depending on shoulder width. Construct shoulder line F-H.
- D-I = 1 to 2 cm (½" to ⅞") depending on neck size.
- H-K = A-C. This is the scye-depth. Construct line H-K and square out the bust line L-K-M.
- L-M = ¼ bust plus 1 cm (½") for side seam.
- N is positioned 6.5 cm (2½") from F.
- N-X = shirt length plus hem allowance. Construct bottom line B-O.
- Separate the yoke from the main back part along the designated line. Add seam allowances along the cutting line of each section after separation.
The yoke is the upper section of the back that sits across the shoulders. It adds style and strength to the shirt at the shoulder line.
To draft the front pattern, lay the back pattern on another area of fabric:
- D-D1 = 6.5 cm (2½") for front overlap and facing allowances, where D-D1 = B-B1.
- D-D3 = 1 cm (⅜") front overlap.
- D-Z = front neck depth. Take ⅙ neck-girth plus 1 cm (½"). Curve the neck-line F-Z-D2.
- V-V1 = 1¼ cm to 4 cm (½" to 1½"). Measure according to the length and circumference of the armhole. Curve the front scye line H-V1-K-M.
The front pattern includes the button placket area where buttons and buttonholes will be placed.
A stand collar (also called a collar band or mandarin collar) consists of two parts: the upper collar and the lower stand or band.
Instructions for drafting:
- A-B = fold line, where A-B is 7.5 cm to 9 cm (3" to 3½").
- B-E = 2½ cm to 4 cm (1" to 1½") – this is the collar-stand width.
- E-A = 4¼ cm to 5 cm (1½" to 2") – this is the collar width.
- A-C = ½ neck-girth plus ½ cm (¼") seam. Draw D-C.
- B-G = ⅙ neck-girth plus 1¼ cm (½").
- D-H = 1¼ cm to 2½ cm (½" to 1"). Curve the base line from H-G.
- H-I = 2½ cm to 3¼ cm (1" to 1¼").
- I-J = 2½ cm to 4 cm (1" to 1½"). Curve from H-J-F.
- J-K = 6½ cm to 10 cm (2½" to 4") depending on collar size and point style at K.
Separating the collar into two pieces:
- Cut from point A-K-J-F-E for the upper part (the collar)
- Cut from point E-F-J-H-G-B for the lower part (the stand or collar band)
Important: Add 1 cm (½") seam allowances on fabric when cutting along line A-K-J, and 2 cm (⅞") along line E-F-J of the collar. For the collar band, add 1 cm (½") seam on line E-F-J-H, and 2 cm (⅞") along the base line.
A short plain sleeve is drafted as follows:
- Draw squared lines A-B-C.
- A-B = sleeve length plus 5 cm (2") for hem.
- A-C = ½ shoulders plus 2½ cm (1"). Square down the line from C to D, where B-D = A-C.
- B-E = D-F = 5 cm (2") hem allowance. Square out lines B-D and E-F.
- C-G = ½ of A-C or according to sleeve hanging style. The distance from A-G should be slightly longer than the front scye line by 1.5 cm (⅝"). Construct line A-G and divide it into three equal sections: A-H-J-G.
- H-I = 1¼ cm (½") and J-K = H-I. Curve the front sleeve head from A-I-J to G. Curve the back sleeve head from A-K to G.
- B-D = ½ sleeve-girth plus 1 cm to 2.5 cm (½" to 1") for side seam.
Easing is the technique of gently gathering fabric to fit a longer edge onto a shorter one, such as easing the sleeve cap into the armhole. This creates a smooth, rounded appearance at the shoulder.
Before starting to make your shirt, gather the following:
- Fabric – choose a suitable type such as cotton, silk, or linen
- Pattern – commercial or readymade pattern
- Scissors – dressmaker's shears for cutting fabric
- Measuring tape
- Pins – tailor's tacking pins
- Sewing machine with appropriate needles
- Hand needles for buttonholes and finishing
- Iron and ironing board
- Buttons or snaps for closures
- Interfacing for collar and placket areas
- Matching thread
Step 1: Prepare Your Fabric
Wash and iron the fabric to remove dirt, wrinkles, and sizing. Lay the fabric flat and fold it in half with right sides facing each other, matching the selvage edges.
Step 2: Cut Out Pattern Pieces
Lay pattern pieces on the fabric according to layout instructions. Pin securely. Cut out fabric pieces carefully, leaving seam allowances as indicated on the pattern. Transfer all pattern markings (darts, notches, pleats) onto fabric using tailor's chalk or pins.
Step 3: Mark and Sew Darts
Darts are small folds that shape the fabric to fit the body. Follow pattern instructions to mark and sew any darts on the front and back pieces.
Step 4: Assemble the Shirt
Pin fabric pieces together with right sides facing. Stitch shoulder seams, side seams, and sleeves following pattern instructions. Try the shirt on for fit and make adjustments.
Step 5: Attach the Collar
If using a stand collar, attach the collar band first along the neckline, then attach the upper collar on top. Ease the collar to fit smoothly around the neck opening.
Step 6: Hem the Sleeves and Bottom
Fold and press hem allowances (about 1.5 cm to 2.5 cm). Stitch hems using a straight stitch.
Step 7: Add Closures
Buttons and Buttonholes:
- Mark buttonhole positions on the right front panel (left side as worn).
- Sew buttonholes using a buttonhole stitch or machine buttonhole function.
- Attach buttons on the opposite side, matching buttonhole positions.
Press Studs:
- Mark positions for press studs on the front placket.
- Snap the male part onto the female part to test.
- Sew the socket part to one side and the stud part to the other.
Step 8: Add Patch Pockets with Flaps
- Cut pocket pieces according to pattern.
- Create the flap by folding and pressing the flap piece, then stitching along the sides and pointed bottom.
- Attach the pocket to the shirt front at the marked position.
- Position the flap above the pocket and stitch along the sides and bottom edge, leaving the top open.
Step 9: Final Pressing
Press the entire shirt to ensure all seams and hems are flat and smooth. A well-pressed shirt looks professional and finished.
Step 10: Trim and Inspect
Carefully trim any loose threads. Inspect the shirt for any imperfections and make final corrections.
A student in Tanzania making a school uniform shirt would follow this sequence:
- Take body measurements: neck = 36 cm, chest = 88 cm, sleeve length = 24 cm
- Using a commercial pattern size that fits these measurements
- Cut 2 front pieces, 1 back piece, 2 sleeves, 1 collar band, 1 upper collar
- Sew shoulder seams at 1.5 cm seam allowance
- Attach sleeves to armholes using 1.5 cm seam allowance
- Sew side seams from hem to sleeve hem
- Attach collar band to neckline
- Attach upper collar to collar band
- Fold front placket and stitch in place
- Make 5 buttonholes and attach 5 buttons
- Hem sleeves and bottom at 2 cm
- Press all seams
In Tanzania, knowing how to make short-sleeved shirts is valuable for small-scale tailors and seamstresses who serve their communities. For example, a tailor in Arusha can use these skills to make school uniforms for students, charging around TSh 25,000 to TSh 40,000 per shirt depending on fabric quality, which provides income while meeting local demand for affordable school clothing. The skills of attaching stand collars, making buttonholes, and adding patch pockets are essential for producing professional-looking shirts that customers can wear to offices, schools, and casual occasions.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Precision in cutting pieces.
- Proper assembly of body, sleeves, and collar.
- Neat and consistent seams.
- Attachment: Correct techniques for short-sleeves.
Tathmini ya matokeo
Make short sleeved shirt conforms to design accurate measurements and specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain ways of making a short sleeved shirt.
Principles: The student should explain the principle involved in making a short sleeved shirt.
Theories: The student should explain: Functionality importance of a short sleeved shirt. Circumstantial Detailed knowledge about:
- Safety aspect
- Environmental issues
Swali
Which of the following measurements is NOT required when drafting a short-sleeved shirt pattern?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado