Mada za sehemu hiiManaging hazardsMada 3
- Controlling mechanical hazards
- Controlling chemical hazards
- Controlling physical hazards
Chemical hazards in leather goods and footwear workshops can cause skin diseases, breathing problems, and long-term illness. Controlling these hazards means using safe methods to prevent chemicals from harming workers and customers.
Chemical hazards are substances that can hurt your body when you touch them, breathe them in, or swallow them. In leather and footwear work, common chemical hazards include:
- Tanning chemicals such as lime, sodium sulphide, acids and chromium salts
- Solvents and adhesives used to join materials
- Dyes and pigments for colouring leather
- Finishing sprays and polishes
- Cleaning agents and degreasers
These chemicals may enter your body through skin contact, inhaling fumes, or accidental swallowing.
Controlling chemical hazards protects:
- Your health and the health of your workmates
- Customers who will use your products
- The environment from pollution
Uncontrolled chemical hazards can cause burns, allergies, asthma, and even cancer over time. In Tanzania the Occupational Safety and Health Authority (OSHA) sets the rules for safe workplaces, and every workshop must follow them.
Follow this order from the strongest to the weakest protection. Start with elimination before moving to the next step.
1. Elimination
Remove the hazard completely so it no longer exists.
- Stitch or nail a sole where this does the job, so that no adhesive is needed
- Buy leather that is already dyed and finished instead of dyeing and spraying it in a small workshop
- Have old chemicals that are no longer used taken away safely
2. Substitution
Replace a dangerous chemical with a safer one.
- Use water-based adhesives instead of solvent-based ones when possible
- Replace solvent-based cleaning agents with water-based cleaners
- Use vegetable-tanned leather instead of chrome-tanned leather where suitable
3. Engineering Controls
Change the workplace or equipment to reduce exposure.
- Install exhaust fans and ventilation systems to remove chemical fumes
- Use enclosed containers for chemicals
- Store chemicals in labelled, sealed containers away from work areas, heat and sunlight
- Never keep a chemical in a drinks bottle or food container; someone may swallow it by mistake
4. Administrative Controls
Change how people work to reduce exposure.
- Write and follow safe work procedures for handling chemicals
- Train all workers on chemical hazard awareness
- Display warning signs and safety data sheets near chemical storage areas
- Never mix chemicals unless the instructions say so. Acid added to sodium sulphide, or to waste that contains it, gives off hydrogen sulphide, a gas that can kill
- When diluting an acid, always add the acid slowly to the water, never water to the acid
- Keep flames, sparks and cigarettes away from solvents and solvent-based adhesives, and keep the lids on
- Limit the time workers spend near chemical hazards by rotating tasks
5. Personal Protective Equipment (PPE)
Wear protective gear to shield your body from chemicals.
- Chemical-resistant gloves when handling solvents or dyes
- A respirator with the correct filter when spraying finishes or using solvents; a simple dust mask stops dust but not solvent fumes
- Safety goggles to protect eyes
- Overcoats or aprons to protect clothing and skin
The label on a container carries a warning symbol for each class of danger:
- Flammable — catches fire easily, such as solvent-based adhesives, thinners and spirit dyes
- Corrosive — burns skin and eyes, such as acids, lime and sodium sulphide
- Toxic or harmful — poisons the body when breathed in, swallowed or absorbed through the skin, such as some solvents and tanning salts
- Irritant or sensitiser — causes rashes, allergy or asthma, such as some dyes, glues and chromium salts
- Dangerous to the environment — poisons water and soil, such as tannery liquors and used solvents
Keep each class apart in the store: flammables away from heat, and acids away from sulphides and from alkalis such as lime.
Safety signs use the same colours everywhere, so that people understand them at a glance:
| Colour | Meaning | Example |
|---|---|---|
| Red | Stop or prohibition; fire equipment | "No smoking"; fire extinguisher |
| Yellow | Warning of danger | "Flammable"; "Corrosive" |
| Blue | You must do this | "Wear gloves and goggles" |
| Green | Safe condition | First aid kit; emergency exit |
Put each sign at eye level, at the place where the danger is, and write safety instructions in short, simple words. Signs matter because visitors and new workers cannot see or smell most chemical dangers.
- Walk through the workshop at regular times, for example once a week, and check labels, lids, leaks, ventilation, signs, protective gear and emergency equipment
- Write a short inspection report: the date, who inspected, what was found, what must be done, by whom and by when
- Keep a maintenance schedule for fans, spray equipment and the fire extinguisher, following the service manuals, and tick each job when it is done
- Between inspections, watch how people work and correct unsafe habits at once
- Investigate every accident and near miss to find the cause, so that the same thing does not happen again. The aim is to learn, not to blame
Keep a first aid kit, clean water for washing skin and eyes, a suitable fire extinguisher, and a bucket of dry sand or sawdust for spills. Everyone should know where they are.
- Chemical on the skin: take off splashed clothing and rinse the skin with plenty of running water for at least 15 minutes
- Chemical in the eye: rinse with clean water for at least 15 minutes, holding the eyelid open, then go to a health facility
- Fumes breathed in: move the person to fresh air at once
- Chemical swallowed: do not make the person vomit; take them quickly to a health facility, with the container or its label
- Spill: keep people away, open doors and windows, put on gloves, soak the spill up with sand or sawdust and put it in a closed, labelled waste container
- After work, clean brushes, containers and spray equipment as the label or service manual says, and store them closed and labelled
- Never pour waste chemicals into drains, streams or onto the ground. Collect them in labelled containers for safe disposal as the law requires
Amina runs a small shoe repair workshop in Arusha. She uses solvent-based adhesive to attach new soles. The fumes cause headaches for her and her apprentice.
Step 1: Amina checks if she can eliminate the problem. Some soles can be stitched on instead of glued, so for those jobs she uses no adhesive at all.
Step 2: Since stitching is not practical for all repairs, she replaces the strong solvent adhesive with a water-based one for most of the remaining jobs.
Step 3: She installs a small exhaust fan above the workbench to remove fumes.
Step 4: She writes a rule that workers must open the windows, keep the adhesive tin closed and allow no flames or smoking whenever a solvent product is in use, and she puts up a "Flammable, no smoking" sign.
Step 5: She buys chemical-resistant gloves for everyone, and respirators with organic-vapour filters for the jobs that still need solvent adhesive.
By combining all five control methods, Amina reduces the health risk significantly.
- Always try elimination and substitution first — they remove the hazard or replace it with a smaller one
- Engineering controls protect many people at once
- Administrative controls depend on people following rules correctly
- PPE is the last line of defence — use it together with other methods
- Read the label and the Safety Data Sheet (SDS, also called MSDS) for every chemical you use
- Never eat or drink in areas where chemicals are stored or used
- Wash hands thoroughly before eating, drinking, or leaving the workshop
A Form 4 student who opens a leather bag workshop in Mwanza will handle dyes, adhesives, and finishing sprays regularly. By applying the hierarchy of controls, the student can first check if safer chemicals exist, then ensure proper ventilation in the workspace, and finally wear the right gloves and respirator as needed. This protects the student's own health while producing quality bags for sale at local markets, and supports a small business that can last.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret service manuals
- Select tools and equipment
- Prepare workshop inspection report
- Prepare workshop color code and safety signs
- Identify any safety hazard material
- Prepare maintenance schedule
- Identify and apply all emergency equipment and supplies
- Monitor safety environment
- Manage uses of safety gears
- Cleaning tools and equipment
- Storing tools and equipment
- Handle hazards materials
Tathmini ya matokeo
Chemical Hazards are managed according to OSHA’s rules and regulations
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Prepare warning signs and safety instruction
- Monitor safe working environment
Principles: The student should explain the principles related in:
- Controlling chemical Hazards
Theories: The student should explain:
- Control classes of hazardous materials
Circumstantial knowledge:
Detailed knowledge of:
- Importance of posting warning sign and safety instructions
- Importance of carry out accident investigation
- Importance of monitoring at safety at working place
Swali
Which of the following is the first step in the hierarchy of controlling chemical hazards?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado