Mada za sehemu hiiCarrying out risk assessmentMada 3
- Controlling risk
- Managing safety gear
- Managing workshop safety rules
When we have identified hazards and assessed risks in our workshop during risk assessment, the next critical step is to control those risks. Controlling risk means taking action to eliminate hazards or reduce the chance that they cause harm. Without proper control measures, even a well-conducted risk assessment is useless — we must act on what we find.
In a leather goods and footwear workshop, hazards such as sharp cutting tools, chemical solvents, noisy machines, and dusty work areas are common. Controlling these risks protects you, your classmates, and your future customers from injury or illness.
A hazard is anything that can cause harm, such as a sharp knife, a solvent or a noisy machine. Risk is the chance that the hazard will actually harm someone, together with how serious that harm would be. A sharp knife locked in a drawer is a hazard with a low risk; the same knife left on a crowded bench is a high risk.
In a risk assessment each hazard is rated, for example low, medium or high, by asking two questions: how likely is the harm, and how bad would it be? The highest risks are controlled first.
Controlling risk is the process of putting measures in place to:
- Eliminate the hazard completely
- Reduce the likelihood of harm occurring
- Limit the severity of harm if it does occur
The goal is to make the workshop as safe as possible for everyone working there.
Risk control methods are arranged in order of effectiveness. Always try the methods at the top of the list first. Move down only if the higher methods are not possible.
1. Elimination
Remove the hazard entirely so it cannot cause harm.
- Example: Buy leather that is already dyed, so that no dyeing chemicals are used in the workshop at all.
- Example: Take a faulty machine out of use until it is repaired.
2. Substitution
Replace the hazardous material or process with a safer alternative.
- Example: Replace a solvent-based adhesive with a water-based glue that gives off no harmful fumes.
- Example: Use a quiet hand tool instead of a noisy power tool for a small job.
3. Engineering Controls
Change the physical workspace or equipment to reduce exposure to hazards.
- Example: Install a local exhaust ventilation system to remove glue fumes from the work area.
- Example: Place a guard on a stitching machine to prevent fingers from touching the needle.
4. Administrative Controls
Change how work is organised or how people behave to reduce risk.
- Example: Create a rule that only trained students may operate the skiving machine.
- Example: Schedule breaks to reduce fatigue when working with sharp tools.
- Example: Display clear safety signs and workshop rules on the walls.
5. Personal Protective Equipment (PPE)
Equip each worker with gear to protect their body from remaining hazards.
- Example: Wearing safety glasses when grinding, buffing or hammering nails and eyelets, to protect the eyes from flying fragments.
- Example: Using rubber gloves when handling dye chemicals, and ear plugs near noisy machines.
Important: PPE should be the last line of defence. It protects individual workers but does not remove the hazard from the workshop. Use it only when other controls cannot fully eliminate the risk.
Follow these steps after completing a risk assessment:
- Identify the hazard — What can cause harm?
- Decide who might be harmed — Workers, visitors, or customers?
- Choose a control method — Use the hierarchy: elimination first, then substitution, engineering, administrative, and finally PPE.
- Implement the control — Put the chosen measure in place immediately.
- Check the effectiveness — Observe whether the control actually reduces the risk. If not, choose a more effective method.
- Review and update — Controls must be reviewed regularly, especially when new equipment or materials are introduced.
- Read the label and the service manual before using any chemical or machine
- Keep chemicals in closed, labelled containers, never in drinks bottles, and store flammable adhesives and solvents away from heat and flames
- Collect waste chemicals, solvent-soaked rags and empty containers in labelled bins for safe disposal; never pour chemicals into drains or onto the ground
- Compressed air is dangerous. Never point an air hose at yourself or at another person, and never use it to blow dust off skin, hair or clothes. Air forced through the skin or into the mouth, nose, ears or eyes can cause serious injury or death
- Wear safety glasses when using compressed air, because it throws dust and chips about
- Check hoses and couplings before use; a hose that breaks loose whips about violently. Shut off the air and release the pressure before disconnecting a tool
Safety signs use the same colour code everywhere:
| Colour | Meaning | Example |
|---|---|---|
| Red | Stop or prohibition; fire equipment | "No smoking"; fire extinguisher |
| Yellow | Warning of danger | "Flammable"; "Moving machinery" |
| Blue | You must do this | "Wear ear protection" |
| Green | Safe condition | First aid kit; emergency exit |
- Stay calm, raise the alarm and tell the person in charge
- Fire: get everyone out by the nearest exit and call for help. Use an extinguisher only on a small fire, only if you have been trained, and only with a clear way out behind you. Never use water on burning solvents or on electrical equipment
- Electric shock: switch off the power at the main switch before touching the person
- Serious bleeding: press firmly on the wound with a clean cloth and get medical help
- Chemical in the eye or on the skin: rinse with plenty of clean water for at least 15 minutes
- Know where the first aid kit, fire extinguisher, main switch and exits are, and check them at every inspection
- Inspect the workshop and all equipment at regular times, for example every week. Use a risk assessment sheet, photograph any problems and write a short report: what was found, what must be done, by whom and by when
- Train every new worker or student before they start: explain the hazards, demonstrate the safe method, let them practise, and keep a record of who was trained
- Make sure enough masks, ear plugs, gloves, aprons, safety boots and goggles are in stock, in the right sizes and in good condition
- Keep the workshop and its surroundings clean: separate leather scraps, paper and chemical waste, and clean and store tools after every job
During a risk assessment in a Form 4 leather workshop, students identified the following hazard:
- Hazard: Chemical solvents used to clean leather produce harmful fumes.
- Who might be harmed: Students using the solvents, and others working nearby.
- Risk level: High — fumes can cause headaches, dizziness, and respiratory problems.
Applying the hierarchy of controls:
- Elimination: Can we remove the solvent completely? The class finds that most leather can be cleaned with a soft brush and a damp cloth, so no solvent is needed for those tasks. → Hazard eliminated for most tasks.
- Substitution: For stubborn stains that still require stronger cleaning, a less toxic solvent is selected. → Substitution applied.
- Engineering controls: Solvent cleaning is moved to a bench beside an open window, with a fan placed to blow the fumes outside, away from the students. → Risk reduced.
- Administrative controls: A safety rule is created: "Solvent cleaning must be done only in the designated area with ventilation running, the container closed after use and no flames nearby." → Risk further reduced.
- PPE: Students wear chemical-resistant gloves and safety glasses when handling any cleaning chemicals. If fumes can still be smelt, a respirator with an organic-vapour filter is needed, because a dust mask does not stop solvent fumes. → Individual protection added.
Result: The combination of controls brings the risk from "High" to "Low," making the workshop safer for everyone.
- Always attempt to eliminate a hazard first before considering other controls.
- Engineering controls and administrative controls reduce risk for everyone in the workshop.
- PPE protects individual workers but does not remove the hazard itself.
- Controls must be checked regularly to ensure they are still working.
- All students should know the emergency procedures in case a control fails.
A young artisan in Arusha who makes sandals using leather dyes can apply risk control by replacing toxic solvent-based dyes with water-based dyes that are safer to breathe in (substitution). If substitution is not possible for a certain colour finish, they would use the dye only in a well-ventilated area (engineering control), enforce a rule that only one person handles the dye at a time (administrative control), and always wear rubber gloves and a respirator suited to solvent fumes (PPE). This approach keeps their small workshop safe and protects their health as their footwear business grows.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret service manuals
- Select tools and equipment
- Supervise practice safe workshop practices to protect yourself, other and properties
- React correctly and safely when faced with an emergency
- Identify and apply correctly all emergency equipment and supplies
- Make periodic inspections of workshop area and all equipment and prepare report
- Conduct safety training
- Identify any safety hazard material
- Handle hazard material correctly
- Prepare universal and know what the color represents
- Be aware of the dangerous of compressed air
- Ensure availability of personal protective equipment
- Monitor good environmental practices
- Clean tools and equipment
Tathmini ya matokeo
Risk assessment carried out as per OSHA and workshop regulations
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Control risk
Principles: The student should explain the principles of:
- React correctly and safely when faced an emergency
- Identifying and applying correctly all emergency equipment and supplies
Theories: The student should explain:
- Carry out risk assessment
- Conducting safety training
- Inspecting workshop areas, tools and equipment
- Handling hazard material correctly
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions while carrying out risk management
Swali
What does risk mean in a leather workshop?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado