Mada za sehemu hiiMaking advanced footwearMada 6
A high boot is a tall leather or fabric shoe that covers the ankle and extends up the leg, often reaching below the knee. Unlike low-cut shoes, it provides extra ankle support, protection, and warmth, making it suitable for rugged outdoor work, farming, riding, and formal occasions.
Before making a high boot, a craftsperson must understand its key features:
- Height — extends well above the ankle, usually 20–40 cm depending on style
- Upper — made from thick, durable leather or strong fabric
- Sole — attached using stitching, adhesives, or a combination of both
- Lining — often included for comfort and warmth
- Fastening — may use laces, zippers, elastic side panels, or straps
- Heel and toe — reinforced for durability and shape retention
A high boot can be designed as a pull-on boot, a lace-up boot or a zip boot. The design is drawn on the last first, and flat patterns are then made from it, with separate patterns for the leg. Because the leg must fit closely yet let the foot pass through, small errors show clearly: a few millimetres wrong in a pattern or seam can make the leg twist, pinch the calf or leave the two boots at different heights. Work precisely at every stage.
1. Taking Measurements and Selecting the Last
- Measure the customer's foot length, ball girth (around the widest part of the foot) and instep girth using a measuring tape.
- Because the boot covers the leg, also measure round the heel and instep, round the ankle, round the calf, and the height of the leg from the floor to where the top of the boot will be. Measure both feet with the customer standing, and write every figure down.
- Choose a shoe last (a foot-shaped wooden or plastic form) that matches the measurements. A boot last is fuller and higher at the instep and ankle than a last for a low shoe.
- The last determines the overall shape and size of the foot of the boot; the leg measurements decide the shape of the leg patterns.
2. Preparing Patterns
- Use cutting patterns marked on paper or card to create the template for each boot part.
- Lay the pattern on the material and mark the outlines with a pencil or chalk.
- Typical boot parts include:
- Vamp (front upper section)
- Quarters (side and heel sections)
- Leg pieces (the tall part that covers the leg)
- Lining pieces
- Toe puff and counter (toe and heel stiffeners)
- Tongue
- Lay all the patterns for the pair close together on the leather to estimate how much is needed, and add an allowance for flaws and waste. A high boot needs much more leather than a shoe because of the long leg pieces.
- Select the lining fabric, the bottom materials (insole board and outsole) and the fittings the design needs, such as eyelets, laces, a zip or buckles.
3. Cutting the Material
- Place the marked material on a cutting board.
- Use a cutting knife or cutting machine to cut along the marked lines precisely.
- Use the strap cutting machine for narrow strips such as bindings or straps.
- Cut matching lining pieces from fabric, and cut the toe puff and counter from reinforcement material.
- Cut in pairs: every left piece needs a matching right piece.
4. Skiving (Thinning Edges)
- Use a skiving machine or a sharp knife to thin the edges of leather pieces where they will be joined.
- This makes seams lie flat and reduces bulk at overlaps.
5. Assembling the Upper
- Hold the seams in position with a thin line of glue, rub them down with the shoe bone, then stitch them on the sewing machine: join the leg pieces, close the back seam, and stitch the vamp to the quarters. Use an awl and hand needles only where the machine cannot reach.
- Fix the tongue in the front opening area and fit the eyelets, zip or other fastening.
- Stitch the lining together and join it to the upper round the top edge.
- Leave the bottom edge (the lasting margin) free; it will be pulled under the last.
6. Lasting the Upper
- Cut the insole to the shape of the last bottom and tack it onto the last with two or three tacks.
- Place the counter (stiff heel piece) between the upper and lining at the heel, and the toe puff at the toe.
- Pull the upper down over the last and check that the back seam is straight and at the right height.
- Apply adhesive to the lasting margin and the edge of the insole. Using pincers, pull the margin over the insole edge and press or tack it down: toe first, then the sides, then the heel, pulling out all wrinkles.
- When the adhesive has set, remove the tacks and hammer the bottom flat.
7. Attaching the Sole
- Rough the lasted margin on the bottom of the boot with the roughing machine until the smooth surface is removed, and fill any hollow in the middle of the bottom. Clean and rough the bonding side of the outsole. Adhesive does not hold on a smooth or dirty surface.
- Apply adhesive to both the boot bottom and the outsole using a 10 mm gluing brush, and let it dry for the time the maker states.
- Place the sole in position, starting at the toe, and press firmly. Beat it down with a mallet, or press the boot in the pressing (plating) machine, for good contact all over.
8. Finishing and Trimming
- Trim any excess material from the edges using a cutting knife.
- Spray finish or dye the upper using a spray gun for a smooth, even colour.
- Leave the boot on the last until the adhesive has fully set, then remove the last carefully so that the back seam is not strained.
- Insert the sock lining over the insole, then clean and polish the finished boot.
9. Quality Check
- Inspect the finished boot for:
- Even stitching and glued seams
- Sole firmly bonded all round with no gaps
- Correct height and symmetry
- Comfortable lining and smooth interior, with no tack points or lumps inside
- Pack the boots in pairs, left with right, with the legs supported so that they do not crease.
A farmer in Arusha needs a durable high boot for working in rough terrain. The craftsperson:
- Measures the farmer's feet, ankles, calves and leg height, and selects a matching size 42 boot last.
- Cuts upper pieces from thick cowhide using a cutting knife.
- Skives the edges where the vamp joins the quarters.
- Stitches the leg pieces, vamp and quarters together using a sewing machine and fits the eyelets.
- Tacks the insole to the last, pulls the upper over it, and lasts the upper with pincers and adhesive.
- Roughs the boot bottom and the rubber sole, glues both, and presses the sole on.
- Sprays the boot with a water-resistant finish, leaves it on the last until the glue has set, then removes the last and fits the sock lining.
The finished boot protects the farmer's ankle from thorns, mud, and water while working in the fields.
- Wear safety gloves when handling adhesives and sharp tools.
- Wear safety boots and a dust coat or overall in the workshop.
- Keep the workspace clean and tools organised to prevent accidents.
- Cut on a firm board with a sharp knife, keeping the other hand behind the blade.
- Keep machine guards in place and fingers clear of the needle. Tie back loose sleeves and hair, and do not wear gloves at the roughing machine or other rotating machines, because a glove can be caught and pull the hand in.
- Adhesives and spray finishes give off flammable, harmful fumes: work with good ventilation, wear a mask when spraying, keep lids closed, and allow no flames or smoking nearby.
- Clean the gluing brush and close the gluing container; clean the spray gun after use.
- Brush leather dust from the machines, sweep the floor, and put scraps, empty glue tins and used tacks in the correct waste bins.
- Return knives (edges covered), pincers, hammers and lasts to their places; keep lasts in pairs.
- Store finished boots in a dry, airy place away from direct sun.
| Term | Meaning |
|---|---|
| Last | A foot-shaped form used to shape the shoe during construction |
| Vamp | The front upper part of the boot covering the toes and instep |
| Quarters | The rear and side sections of the upper |
| Counter | A stiff piece placed inside the heel for shape and support |
| Skiving | Thinning the edges of leather for smooth joins |
| Roughing | Texturing the leather surface to improve glue bonding |
| Lasting | Pulling the upper over the last and fixing its bottom edge to the insole |
In Tanzania, a craftsperson in Morogoro who masters high-boot making can start a small workshop producing custom boots for local farmers, construction workers, and police officers. Well-made handcrafted high boots sell for more than ordinary shoes, providing a reliable income and serving community needs for durable, protective footwear.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret designs
- Select tools and materials
- Select standard lasts
- Select patterns or dies
- Estimate amount of leather required as per design
- Select fabric lining
- Select bottom materials
- Select required accessories and fittings
- Lay patterns on leather and trace
- Lay patterns on fabrics and trace
- Lay patterns on reinforcements and trace
- Cut out leather
- Cut out fabrics
- Cut out reinforcements
- Assemble shoe upper using glue
- Stitch shoe upper using sewing machine
- Assemble bottom insole
- Tack insole on last
- Pull on the shoe upper
- Cement the shoe bottom
- Last the upper
- Rough shoe bottom
- Clean outsole and rough it
- Apply glue on the shoe bottom
- Apply glue on the outsole
- Attach the sole
- Press the footwear
- Clean the footwear
- Spray the footwear
- Remove last
- Insert soak lining
- Finished and quality control
- Pack into pairs
- Observe safety
- Clean footwear
- Clean tools and equipment
- Store footwear
- Store tools and equipment
Tathmini ya matokeo
High boot produced conforms to design and required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Make high boot
Principles: The student should explain the principles related in:
- Taking foot measurements for high boot
Theories: The student should explain:
- Characteristics of high boot
- Shapes of high boot shoe lasts
- Ways of designing high boot
- Uses of footwear materials
- The importance of precision and attention to details while making high boot
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to making high boot
- Safe handling of tools and equipment
Swali
What does a high boot give the wearer that a low-cut shoe does not?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado