Mada za sehemu hiiMaintaining of cutting and sewing machinesMada 2
- Maintaining sewing machines
- Maintaining skiving machines
A skiving machine is a specialised tool used in leatherwork to shave or thin the edges of leather, making it easier to fold, join, or stitch pieces together neatly. Regular maintenance keeps the machine running smoothly, produces clean cuts, and extends its working life.
The skiving machine found in most workshops is the bell-knife skiver. To maintain it you must know its parts and what each one does:
| Part | Function |
|---|---|
| Bell knife | A round, cup-shaped steel knife that spins at high speed; its sharp rim shaves the leather |
| Feed roller | A rough roller under the presser foot, close to the knife edge, that grips the leather and pushes it against the knife |
| Presser foot | Holds the leather down on the feed roller; its height and angle set the thickness and slope of the skive |
| Edge guide | A stop that the edge of the leather runs against; it sets the width of the skive |
| Grinding stone | A small built-in sharpening wheel that is brought against the knife to keep it sharp |
| Motor, belt and pulleys | Supply the power and carry it to the knife and the feed roller |
| Foot pedal | Works a clutch that connects or disconnects the drive, so the operator controls the feeding |
| Waste chute and guards | The chute carries the shavings away; the guards cover the knife, belt and pulleys |
How the movement is passed on: the motor turns a belt and pulleys. These turn the shaft that carries the bell knife and, through gears, the feed roller. The turning feed roller carries the leather under the presser foot to the edge of the spinning knife.
The skiving machine is one of several cutting machines used in leatherwork. A splitting machine uses a long band knife to reduce the thickness of a whole piece, and a cutting (clicking) press pushes shaped knives through the leather to cut out parts. Hand cutting tools include cutting knives, skiving knives, scissors and punches. All of them need the same care: keep them clean, sharp and lightly oiled against rust, and store them with their edges protected.
Before starting, gather these tools and materials:
- Screwdrivers (assorted sizes)
- Spanners (assorted sizes)
- Allen key
- Lint brushes
- Pliers
- Dusters
- Spare parts or repair accessories
- File
- Measuring tape
- Notepad for recording observations
- Lubricating oil and grease of the kind the maker recommends
- The maker's instruction manual for the machine
Work through these steps in order every time you service the machine.
Step 1: Prepare the Work Area and Machine
- Clear a clean, flat workspace large enough to lay out tools and removed parts.
- Switch off the machine, wait until the knife has stopped turning completely, and unplug it from the power supply.
- Record the current machine settings in your notepad so you can return them to the original position after servicing.
Step 2: Clean the Machine Thoroughly
- Use a lint brush and duster to remove leather dust, debris, and old oil residue from all exposed surfaces.
- Brush away shavings, fluff, threads and dust from around the knife, the feed roller, the presser foot and the waste chute. Brush away from the knife edge, never towards it.
- Use pliers carefully to pull out any compacted pieces of leather stuck in tight gaps.
- Wipe all surfaces with a clean, dry duster.
Step 3: Inspect All Parts for Wear or Damage
Check each component and note your findings:
- Blade (bell knife): Look for dull edges, chips, or cracks. A damaged blade produces ragged cuts.
- Feed rollers: Check for flat spots, cracks, or excessive wear that could cause uneven feeding.
- Springs and tensioners: Ensure springs are not stretched or broken.
- Screws and bolts: Tighten any that are loose. Replace any that are rusted or stripped.
- Drive belt (if applicable): Look for cracks, fraying, or slack.
Use the file gently to remove small burrs from metal parts if instructed to do so. Replace worn or broken parts only with the correct spare parts for that machine, fitted as the maker's manual shows.
Step 4: Lubricate Moving Parts
- Apply a few drops of the recommended oil at each oiling point shown in the maker's manual, such as shaft bearings, pivots and adjusting screws.
- Put grease on gears and other parts that the manual says need grease, using a grease gun or a small brush.
- Keep oil and grease off the feed roller, the knife edge and the drive belt, because they make the leather and the belt slip.
- Wipe away excess oil and grease with a duster to prevent them from staining leather during use.
- Record the date and type of oil used in your notepad.
Step 5: Adjust Settings and Tension
- Make all adjustments with the machine switched off and the knife standing still.
- Set the height and angle of the presser foot with its adjusting screws to give the thickness and slope of skive you need.
- Set the edge guide for the width of the skive.
- Check and reset the feed roller pressure using the tension spring, and check that the gap between the feed roller and the knife edge is small and even.
- Check that the drive belt is neither slack nor too tight.
- Refit all guards and covers, reconnect the power, run the machine briefly and listen for unusual sounds.
Step 6: Test the Machine
- Run a scrap strip of leather through the machine to confirm it skives cleanly and evenly along the entire edge, without tearing.
- Use the measuring tape to check the width of the skive, and feel the skived edge between finger and thumb to check that its thickness is even.
- Check that the feed rollers pull the leather through steadily without slipping.
- Make any final small adjustments, stopping the machine each time, until the result is smooth and consistent.
Step 7: Clean Up and Store
- Sweep up the leather shavings and dust and put them in the waste bin. Put oily dusters in a closed metal bin.
- Wipe the tools and return the screwdrivers, spanners, Allen key, pliers and brushes to their places.
- Put spare parts back in their labelled container, and note in your notepad any part that was used or is still needed.
- When the machine is not in use, leave it switched off, unplugged and under a dust cover.
- Always disconnect power before opening, cleaning, oiling or adjusting any part of the machine.
- Handle the blade with extreme care — it is very sharp and can cause serious cuts.
- Keep fingers away from the blade and feed opening while the machine is running.
- Do not wear gloves, loose sleeves, bracelets or untied long hair near the machine when it is running, because they can be pulled into the moving parts. Gloves may be worn only for handling the knife with the machine switched off and unplugged.
- Never run the machine with a guard or cover removed.
- Sharpening the knife on the built-in grinding stone throws sparks. It is done only under the teacher's supervision, wearing eye protection.
| Problem | Likely Cause | Fix |
|---|---|---|
| Leather tears instead of cutting cleanly | Dull knife | Sharpen the knife on the grinding stone, or fit a new knife if it is chipped or worn down |
| Uneven skiving thickness | Worn, dirty or loose feed roller, or presser foot set wrongly | Clean, tighten or replace the roller; reset the presser foot |
| Machine makes rattling noise | Loose screws or missing lubricant | Tighten screws and lubricate |
| Leather slips during feeding | Low roller pressure | Increase tension on springs |
In Tanzania, many informal cobblers and leather workers in markets such as Kariakoo in Dar es Salaam or around Arusha use skiving machines to prepare leather for making shoes, bags, and belts. A cobbler who regularly maintains their skiving machine can earn more because they complete orders faster and produce higher-quality finished goods. If a machine breaks down due to poor maintenance, the repair can be expensive and work stops while the machine is out of use, whereas routine cleaning and oiling costs almost nothing.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Operate the skiving and cutting machines
- Clean and maintain the safety of the skiving and cutting machines
- Select the proper tools and materials to use with the machine
- Service parts as directed from the manufacturer’s instruction manuals.
- Remove fluff, dust, dirt and tiny threads
- Replace worn out parts with proper/new ones
- Tighten or loosen screws
- Apply recommended lubricants regularly
- Put grease using servicing tools
- Wipe off excess oil and grease
- Adjust and fix defective parts correctly
- Observe safety
- Clean workplace
- Store tools and equipment correctly
Tathmini ya matokeo
A skiving machine is maintained by replacing the defected parts as per required standards
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Describe cutting machine
- Take care of cutting tools
- Service cutting machines
- Maintaining and care skiving machine equipment
Principles: The student should explain the principles involved in:
- Storing skiving machine
- Maintaining skiving machines and equipment
- Caring of equipment and machines in the workshop
Theories: The student should explain:
- Types of cutting machine
- Categorisation of cutting tools
- Structure of the cutting machine
- The functions of each part of the cutting machine
Circumstantial knowledge:
Detailed knowledge of:
- Benefits of maintaining workshop machines and equipment
- Different kinds of cutting machines.
- Structural development of the cutting machine
- Safety procedures when using skiving machines
- Kinematic system of the skiving machine
Swali
What is the function of the bell knife in a skiving machine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado