Mada za sehemu hiiPerforming simple stitchingMada 5
In shoe making, the quarter is the back part of the shoe upper that covers the heel and side portions of your foot. When you look at a shoe, the quarter is the section that wraps around your ankle and heel, while the front part covering your toes is called the vamp. Together, the quarter and vamp form the complete upper of a simple shoe. Most shoes have two quarters, an inside quarter and an outside quarter, which are joined to each other at the back of the heel by the back seam.
Other footwear components you should be able to name are the tongue, the toe cap, the lining, the insole, the sole and the heel.
Before starting, gather the following:
- Paper or cardboard patterns for the quarter
- Leather or fabric material for the upper
- Cutting knife or scissors
- Skiving knife for thinning leather edges
- Awl for marking stitch lines
- Measuring tape and dividers
- Hole punches for stitch holes
- Wooden mallet or plastic hammer
- Sewing machine or hand-sewing needles
- Strong thread (waxed thread for leather)
- Upper glue
- Safety boots and overall or dust coat
Study the working drawing to see the shape of the quarter, where it joins the vamp and where the stitch lines run. Lay the quarter pattern on the grain side of the leather, away from scars and holes, and trace round it carefully. Turn the pattern over to trace the second quarter, so that you get a matching inside and outside quarter and not two of the same side. Check the measurements with a measuring tape. Mark all notches, punch holes, and stitch lines clearly on the material. These marks guide you during cutting and stitching.
Place the material flat on the workbench. Hold the cutting knife firmly and cut along the pattern lines with smooth, steady strokes. Keep the hand that holds the leather behind the blade, never in front of it. Always cut on the waste side of the line so your finished piece stays the correct size.
Thin down the edges where the quarter will be joined to other parts, such as the vamp. Lay the leather flesh side up on a smooth, hard surface. Hold the skiving knife at a shallow angle and shave off thin layers of leather, pushing the blade away from you. This is hand skiving. A skiving machine does the same job faster and more evenly, and is used only under supervision. This makes the edges flexible enough to fold and join cleanly without creating bulky seams.
Use an awl to prick-mark the stitch line along the edge of the quarter. Space the marks evenly, usually about 3 to 4 millimetres apart. These marks show where each stitch will go. For hand stitching, make a small hole at each mark with the awl or with the smallest hole punch, tapping the punch with the mallet.
First join the two quarters at the back seam: place them grain sides together with the back edges level and stitch along the back stitch line. Thread a needle with waxed thread and knot the end. Push the needle through the first hole from the back to the front. Move on to the next hole and insert the needle from front to back, pulling the thread snug. Continue this in-and-out pattern along the entire seam, then stitch back through the last two holes to fasten the end. Keep stitches equal in size and tension for a neat, strong seam.
In a workshop, quarters are normally stitched on a sewing machine, which makes the same seam much faster. The stitch length is set to about 3 mm, the stitch is tested on an offcut first, and both ends of the seam are fastened by sewing back over the last few stitches. Keep your fingers away from the needle, and switch the machine off before threading it or changing the needle.
Worked Example: If your quarter has a seam joining it to the vamp, you will stitch along the joining edge. With 20 prick marks along this edge, you will make 19 stitches, each pulling the two pieces firmly together so no gap remains.
Open the back seam, fold one seam allowance to each side and tap it flat with the hammer. A little upper glue under the allowances holds the seam flat. Then finish the top edge of the quarter: either apply glue to the skived edge, fold it over about 4 mm and tap it down, or leave it as a raw edge and bevel, paint and glaze it. Trim any excess thread, rub off any glue that has squeezed out and wipe away marking lines with a soft cloth. Your quarter is now ready to be joined with the vamp and other parts of the shoe upper.
- Always wear safety boots when working with sharp cutting tools
- Use a cutting mat or scrap wood under your material to protect the workbench
- Keep knives sharp — a dull knife requires more force and slips more easily
- Wear an overall or a dust coat to protect your clothing
- Use upper glue in a well-ventilated place, close the tin after use and keep it away from flames, because its fumes are harmful and catch fire easily
- At the sewing machine and the skiving machine, tie back long hair and loose sleeves, keep your fingers clear of the needle and the knife, and never remove a guard
- Report every accident at once
For a small cut or a needle prick, wash the wound with clean water and soap, press on it with a clean cloth until the bleeding stops, and cover it with a clean dressing. For a deep cut, keep pressing firmly on the wound with a clean cloth, raise the hand and get help at once. If glue gets into the eyes, rinse them with plenty of clean water and seek medical help.
- Brush dust and threads off the stitched quarters and store them flat, in pairs, in a clean, dry place away from sunlight
- Wipe knives, punches, the awl and hammers with a dry cloth, cover the blades and return every tool to its place
- With the power off, brush lint from the sewing machine and cover it
- Put small offcuts, skivings and thread ends in the waste bin, and keep larger offcuts for small parts and test pieces
- Put glue-covered rags and empty glue tins in the bin provided for them, and never burn leather waste or glue tins, because they give off harmful smoke
In Tanzania, many small shoe-repair shops in towns like Arusha and Dar es Salaam rely on skilled cutting and stitching of shoe quarters to restore worn footwear. A cobbler might stitch a new quarter onto a customer's old shoe upper, extending the shoe's life at a much lower cost than buying a new pair — an important skill for earning income and serving the community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student correctly should be able to:
- Interpret drawing
- Select tools and equipment
- Select materials
- Stitch different parts of cut leather pieces
- Stitch simple quarters
- Make edge finishing
- Observe safety
- Clean stitched pieces
- Clean tools and equipment
- Store stitched pieces
- Store tools and equipment
Tathmini ya matokeo
Quarters are cut and stitched according to the specifications required
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should clearly explain how to:
- Fold different parts of leather pieces
- Stitch different parts of leather pieces
- Finish different stitched leather pieces
Principles: The student should correctly explain the principles of:
- Machine skiving and hand skiving
- Machine stitching
- Quality finishing
Theories: The student should explain correctly:
- Names of footwear components
- Names of leather goods components
- Use of different ways of stitching
- Finishing procedures
- The importance of precision and attention to details when performing simple stitches
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to stitching operations
- Safe handling of work tools and equipment
- First aid
- Wastes disposal
Swali
What is the quarter in shoe making?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado