Mada za sehemu hiiConducting corrective maintenance of sewing machinesMada 5
- Replacing the bobbin and bobbin case
- Replacing the needle bar and needle plate
- Replacing the feed dog
- Replacing the tension disc
- Setting the needle against hook timing
The bobbin is the small spool that holds the lower thread of a lockstitch sewing machine, and the bobbin case is the metal holder that carries the bobbin and controls the tension of that thread. Both sit in the hook under the needle plate. A bent bobbin or a damaged bobbin case gives loose, looped or skipped stitches and thread jams, so a defective one is taken out and replaced with a new one of the same type.
A sewing machine joins pieces of leather or fabric with rows of stitches, and is also used for decorative stitching. Machines differ in several ways:
- By drive: hand-operated, treadle (foot-driven) and electric
- By use: domestic machines for light work, and industrial machines for long hours and heavier materials
- By shape of bed: flat-bed for flat pieces, cylinder-arm for bags and tubular work, and post-bed for shoe uppers
- By stitch: lockstitch machines, which use a bobbin, and chain-stitch machines, which do not
The machine head is the complete upper part of the machine. Its main parts are the arm and bed, the handwheel, the needle bar and needle, the presser foot, the thread take-up lever, the tension unit, the stitch length regulator, the needle plate, the feed dog and, under the bed, the hook that holds the bobbin case.
- The bobbin is bent, cracked or rusty, or it wobbles and rattles as it turns
- The rim of the bobbin is rough or nicked and catches the thread
- The bobbin case is dented, or has burrs where the needle has struck it
- The tension spring on the bobbin case is bent, loose or worn into a groove
- The latch no longer holds the case firmly in the hook
- Screwdrivers of the right sizes, including a very small one for the bobbin case
- Lint brush, pliers and duster
- Sewing machine oil
- A new bobbin and bobbin case made for that model of machine
- Notepad
Step 1: Make the machine safe
Switch off the machine and unplug it, and wait until the motor has stopped turning. Turn the handwheel towards you by hand until the needle is at its highest point, and raise the presser foot.
Step 2: Remove the old bobbin case and bobbin
Open the slide plate beside the needle plate, or reach under the bed, to get to the hook. Lift the small latch on the bobbin case and pull the case straight out. No screw holds the bobbin case in the machine: the latch locks it onto the centre pin of the hook. Let go of the latch and tip the bobbin out of the case.
Step 3: Clean the hook area
Unscrew the needle plate with a screwdriver that fits its screws. Brush fluff, dust and dirt out of the hook and from around the feed dog with the lint brush, and pick out tiny threads with the pliers. Do not blow into the machine, because breath is damp and pushes lint further in. Wipe off excess oil and grease with the duster, then put one drop of sewing machine oil on the hook if the manual asks for it. Refit the needle plate and tighten its screws firmly.
Step 4: Prepare the new bobbin and bobbin case
Compare the new parts with the old ones: they must be the same size and shape. Wind thread evenly onto the new bobbin, not beyond its rim. Place the bobbin in the case so that it turns in the direction shown in the machine's manual when the thread is pulled. Draw the thread into the slit in the case and under the tension spring until it comes out at the end of the spring. Leave about 10 cm of thread hanging.
Step 5: Check the bobbin thread tension
Hold the end of the thread and let the bobbin case hang. It should stay where it is, and slide down a little when you give the thread a small jerk. If the case drops freely, tighten the small screw on the tension spring; if it does not move at all, loosen it. Turn the screw only a quarter-turn at a time. Turning it clockwise tightens the tension.
Step 6: Fit the bobbin case
Hold the case by its open latch and push it onto the centre pin of the hook, with the projecting finger of the case in its notch. Release the latch and press the case until it clicks. A case that is not locked in will be struck by the needle.
Step 7: Bring up the bobbin thread and test
Close the slide plate. Hold the needle thread lightly and turn the handwheel towards you one full turn, so that the needle goes down and brings up a loop of bobbin thread. Pull both threads under and behind the presser foot. Plug in the machine and sew a test seam on a scrap of leather. The two threads should lock in the middle of the material, with no loops on either side.
Step 8: Clean the workplace
Put the defective bobbin and bobbin case in the scrap metal container so that nobody uses them again. Sweep up lint and thread ends, wipe the tools and return them to the toolbox, and wipe any oil from the machine bed so that it does not stain the next piece of work.
| When | What to do |
|---|---|
| Every day | Brush lint from the hook and feed dog, oil the machine as its manual says, wipe it and cover it after work |
| Every week | Remove the needle plate and clean thoroughly; check the needle, bobbin, bobbin case and drive belt |
| Every month or term | Tighten loose screws, check the thread tension, replace worn parts |
Write each job and its date in the notepad, so that anyone can see when the machine was last serviced.
- Always switch off and unplug the machine before putting your fingers near the needle or the hook
- Only one person works on the machine at a time
- Keep small screws in a dish so that none fall into the machine
- Never keep using a bent bobbin or a damaged bobbin case: it can break the needle and send pieces flying
- If a needle pricks your finger, wash the wound with clean water, cover it with a plaster and report it
Amina is stitching a school bag on an industrial sewing machine in the school workshop. The stitches underneath are loose and looped, and re-threading does not help. She switches off, removes the bobbin case and sees that its tension spring is bent and the rim of the bobbin is nicked. She cleans the hook area, wipes off the old oil, threads a new bobbin into a new bobbin case of the same model, checks the tension by letting the case hang from the thread, and clicks the case into the hook. She brings up the bobbin thread, tests on a leather scrap and gets tight, even stitches. She writes the date and the parts replaced in the notepad.
A craftsman in Morogoro who repairs shoes and bags depends on his sewing machine every day. When the stitches start to loop, he can check the bobbin and bobbin case, replace them in a few minutes with the spares he keeps, and carry on serving customers instead of losing a day's work waiting for a technician.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools
- Remove fluff, dust, dirt and tiny threads
- Remove a defective bobbin and bobbin case, and replace with new ones
- Tighten or loosen screws
- Wipe off excess oil and grease
- Observe safety
- Clean workplace
Tathmini ya matokeo
The bobbin and bobbin case are replaced in their correct positions according to the specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Replace the bobbin and bobbin case
- Develop a maintenance schedule for a sewing machine
Principles: The student should explain the principles of: Replacing the bobbin and bobbin case
Theories: The student should explain:
- The structure of a sewing machine head
- Different types of sewing machines
- The functions of sewing machines
Circumstantial knowledge:
Detailed knowledge of:
- Safety procedures
Swali
What is the first safety step you must take before replacing the bobbin and bobbin case?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado