Mada za sehemu hiiConducting corrective maintenance of lasting machinesMada 3
- Performing maintenance and restoration of toe-lasting machine
- Performing maintenance and restoration of heel seat lasting machine
- Performing maintenance and restoration of pounding machines
A heel seat lasting machine is a specialised piece of equipment used in shoe manufacturing to stretch and shape the upper leather or material around the heel area of a shoe last (the foot-shaped form). It pulls the material tightly over the heel seat, ensuring a smooth, wrinkle-free finish. Proper maintenance and timely restoration of this machine are essential to produce quality footwear.
- Last support (last pin): holds the last, with the insole and upper on it, bottom up
- Heel band: a padded band, often faced with a non-stick Teflon band, that clamps the upper round the back of the last
- Wipers (wiper plates): slide over the heel seat and fold the lasting margin onto the insole
- Injector block: a heated block with nozzles that feeds hot-melt adhesive onto the heel seat of the insole
- Heaters and temperature controller: melt the adhesive and hold it at the set temperature
- Laminator: on machines fitted with one, a heated pressing unit that bonds layers together using heat and pressure
- Pedal, valves and cylinders: start and carry out each movement
Electricity runs the motor, the heaters and the controls. Compressed air, cleaned and regulated in the air service unit, moves the heel band and other parts through cylinders. In one working cycle the shoe is placed on the last support, the heel band clamps the back of the upper, adhesive is injected, the wipers close and press the margin onto the heel seat, the pressure is held for a few seconds, and the machine opens.
Regular maintenance and restoration of the heel seat lasting machine ensure that:
- The machine operates efficiently and produces consistent results
- Parts wear out evenly and last longer
- Safety hazards are minimised
- Production quality remains high
- Costly breakdowns and replacements are avoided
Before performing any maintenance or restoration work, always observe these safety measures:
- Wear safety boots to protect your feet
- Put on safety gloves to protect your hands
- Wear a dust coat or overall to protect your clothing
- Use a mask against dust, and use solvents only in a well-ventilated place away from flames
- Ensure the machine is switched off and unplugged, the air supply is closed and the air pressure is released
- Let the adhesive and heated parts cool before touching them; hot-melt adhesive causes deep burns
- Leave electrical repairs to a qualified technician; never work on live parts
- Wear no loose clothing or jewellery, tie back long hair, and keep hands clear of the heel band and wipers when testing
- Keep the workbench clean and organised
- Read the operation manual for specific safety guidelines
Gather the following tools before starting:
- Screwdrivers (set)
- Set of spanners
- Set of Allen keys
- Hammer
- Scissors
- Lubricants (as recommended in the operation manual)
- Clean rags
- Safety equipment (gloves, boots, mask, dust coat)
Step 1: Visual Inspection
Examine the machine carefully for any visible signs of damage, loose parts, or abnormal wear. Check:
- All bolts and screws are tight
- No cracks or bends in the frame
- Worn or frayed cables or hoses
- Proper alignment of mechanical parts
Step 2: Cleaning
Remove dust, leather scraps, and debris from all parts of the machine:
- Use a brush or clean rag to wipe away loose dirt
- Remove built-up leather dust from moving parts
- Clean the wipers and heel band thoroughly
- Ensure no debris blocks the mechanism
Step 3: Lubrication
Apply lubricants to all moving parts to reduce friction and prevent premature wear:
- Identify all points requiring lubrication (refer to the operation manual)
- Apply a few drops of the recommended lubricant to each point
- When the work is finished and the guards are back in place, run the machine briefly to spread the lubricant evenly
- Wipe away any excess lubricant
Step 4: Checking and Adjusting Components
Inspect and adjust key components:
- Wipers: Ensure they move freely and are properly aligned
- Heel band: Check for wear and adjust pressure settings
- Springs: Verify they have adequate tension
- Pedal mechanism: Ensure smooth operation without sticking
Tighten any loose fasteners using the appropriate screwdriver, spanner, or Allen key.
Restoration becomes necessary when parts are significantly worn or damaged.
Step 1: Disassembly
Carefully dismantle the affected parts following the operation manual:
- Label or sketch parts before removing them for easier reassembly
- Use appropriate tools (screwdrivers, spanners, Allen keys) to avoid damaging fasteners
- Handle delicate components like springs and the heel band with care
Step 2: Part Inspection and Repair or Replacement
Examine each removed component:
- Identify worn, cracked, or broken parts
- Repair minor damage where possible (straightening bent parts, re-threading stripped screws)
- Replace parts that cannot be repaired with new ones of the same specifications
Step 3: Reassembly
Reassemble the machine in the correct order:
- Replace all cleaned or new parts in their original positions
- Ensure proper alignment of all components
- Tighten all fasteners securely but avoid over-tightening
- Reconnect any disconnected cables or hoses
Step 4: Testing
After reassembly, test the machine:
- Refit the guards, reconnect the power and air, then switch on the machine and observe its operation
- Check that all movements are smooth and consistent
- Verify that wipers and heel band function correctly
- Listen for unusual sounds that may indicate problems
- Make final adjustments as needed
Settings differ between models, so use the figures in the operation manual and change one setting at a time.
- Setting the laminator: With the machine cold, check that the pressing surfaces are clean and undamaged. Set the pressure and pressing time given in the manual and test on scrap material. The layers must bond all over without wrinkles, bubbles or scorch marks.
- Setting the injector block: Clean the nozzles only when the block is cold. Fit the block so that the nozzles follow the curve of the heel seat, and set the amount of adhesive so that a thin, even line is laid. Too little gives a weak bond; too much squeezes out and dirties the upper.
- Regulating the temperature: Set the controller to the temperature recommended for the adhesive and wait until it is reached before lasting. Adhesive that is too cold is thick and does not bond; adhesive that is too hot burns, darkens and blocks the nozzles.
- Replacing the Teflon band: Replace the band when it is worn, torn or coated with adhesive. Isolate the machine and let it cool, loosen the clamp screws, remove the old band, cut the new band to the same size with scissors, fit it flat without twists and tighten the clamps evenly. Run a trial cycle to check that it closes evenly round the heel.
A Form 2 student at a vocational training centre notices that the heel seat lasting machine produces shoes with wrinkles around the heel area. Investigation reveals:
- The wipers are sticky and do not move freely
- Heel band pressure is uneven
- The machine has not been lubricated for several weeks
After switching off and isolating the machine, the student performs maintenance by:
- Cleaning the sticky wipers with a solvent and rag
- Applying lubricant to all moving parts
- Adjusting the heel band pressure using the adjustment screws
- Tightening loose bolts on the heel band assembly
After testing, the machine produces smooth, wrinkle-free heel seats again.
- Always disconnect power before performing maintenance
- Use the correct tools for each task to avoid damaging the machine
- Follow the operation manual for specific instructions
- Regular cleaning prevents buildup that causes mechanical problems
- Proper lubrication extends the life of moving parts
- Never skip safety precautions, even for quick maintenance tasks
- Put oily rags, old adhesive and worn parts in the correct waste containers
| Problem | Likely Cause | Solution |
|---|---|---|
| Sticking wipers | Hardened adhesive, dirt or dried lubricant | Clean the wipers and lubricate their slides |
| Uneven lasting | Worn or badly set heel band or wipers | Adjust them, or replace worn parts |
| Noisy operation | Lack of lubrication | Apply lubricant to moving parts |
| Loose parts | Vibration loosening fasteners | Tighten all fasteners regularly |
| Adhesive does not bond | Temperature too low or a blocked nozzle | Reset the temperature; clean the nozzles when cold |
| Marks on the upper | Worn or dirty Teflon band | Replace the Teflon band |
In a small shoe factory in Arusha, an operator uses a heel seat lasting machine daily to last the backs of new shoes. By performing regular maintenance—cleaning, lubricating, and tightening loose parts—the operator avoids costly machine breakdowns and produces neatly lasted shoes. This reliable work keeps production running, protects the factory's reputation and secures the workers' income.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Set the laminator
- Set the injector block
- Temperature regulation
- Replace the Teflon band
- Observe safety precautions and instructions
- Lubricate and service lasting machines
Tathmini ya matokeo
The working heel seat lasting machine is restored properly
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should correctly explain how to perform maintenance and restoration of the heel seat lasting machine
Principles: The student should explain the principles of maintaining and restoring of heel seat lasting machine
Theories: The student should clearly explain the procedures for servicing and repairing the heel seat lasting machine
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions for the heel seat lasting machines
- Safe handling of lasting machines
Swali
Before maintenance starts on a heel seat lasting machine, it is switched off and unplugged. What else must be done to make the machine safe to work on?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado