Mada za sehemu hiiMaking leather skirts and trousersMada 2
- Making leather skirts
- Making leather trousers
Leather trousers are garments made from soft leather that cover the body from the waist to the ankles. They have a waistband, a fly opening with a zip, pockets and, usually, a fabric lining. Leather does not behave like cloth: every needle hole is permanent, pins leave marks, and too much heat spoils it. Each stage must be planned and done carefully.
- Measuring tape and steel ruler — for body measurements and straight lines
- Patterns — ready-made or drafted paper pieces for each part
- Cutting knife, scissors, clicking dies and cutting machine — for cutting leather, lining and foam
- Skiving machine — thins leather edges so that seams and folds lie flat
- Sewing machine with leather-point needles and strong polyester thread; hand needles and a thimble for hand finishing
- Mallet, hammer and awl — for flattening glued seams and marking positions
- Glue and brushes — to hold seams and hems
- Iron, ironing table, spray gun and soft brushes — for pressing and finishing
- Button-fixing machine — for press studs and fastening buttons
- Materials — soft garment leather, lining fabric, thin sponge foam for padded parts, a zip, buttons or press studs, and reinforcing tape for the waistband, pocket openings and fly
Check that knives are sharp and that the machine is oiled, threaded and set to a long stitch (about 3 mm). Short stitches cut leather like a row of perforations.
Leather has a smooth grain side and a rough flesh side. The fibres are tightest along the backbone and loosest in the belly, which stretches easily. Cut the leg panels from the firm area with their length parallel to the backbone, and use the belly only for small hidden parts such as facings. Check each skin for holes, scars and thin places, and mark them on the flesh side so that you can cut around them.
Step 1: Take Measurements
Measure the waist, the hips at the fullest part, the thigh, the inside leg (crotch to ankle), the outside leg (waist to ankle) and the crotch depth. Write them down.
Step 2: Interpret and Adapt the Pattern
Decide the style first: leg shape, pocket type, lined or unlined. Then read every pattern piece: its name, how many to cut, the grain-line arrow, the notches (matching points), the seam allowance, fold lines, and the pocket and zip positions. To adopt a ready-made pattern, choose the size nearest the hip measurement, then alter the leg length and the waist. Test the fit in cheap fabric first, because leather cannot be let out once it is stitched.
Step 3: Lay, Trace and Cut
- Lay the leather flat, flesh side up. Place the pattern pieces close together, with the grain-line arrows parallel to the backbone
- Turn the pattern over for the second leg so that you cut a left and a right
- Hold patterns with weights, never pins. Trace with tailor's chalk or a silver pen
- Cut the leather in a single layer with a sharp knife or scissors, in long smooth strokes
- Lay the lining patterns on the fabric, trace and cut. Trace and cut foam for any padded part slightly smaller than its leather piece, so that it stays clear of the seams
Step 4: Skive and Glue
Skive the seam allowances of the waistband, fly and pocket edges. Hold parts together for stitching with clips or a thin line of glue instead of pins. Glue foam lightly to the flesh side of its panel.
Step 5: Stitch in Order
- Make the pockets on the front panels and reinforce the openings
- Stitch the front crotch seam below the zip mark and set the zip into the fly
- Join each front to its back at the side seam, then at the inside leg seam
- Stitch the crotch seam from the bottom of the fly to the centre back waist; stitch it twice for strength
- After each seam, glue the seam allowances open and tap them flat with the mallet
- Stitch the lining in the same order, holding its turnings with a little glue, then stitch it to the trousers at the waist
- Attach the reinforced waistband, then turn up the hems, glue them and tap them flat
Do not sew backwards and forwards several times at the end of a seam; tie off the threads instead.
Step 6: Attach Fittings, Iron and Finish
- Fix the waistband button or press stud with the button-fixing machine
- Iron on the flesh side, or through brown paper or a dry cloth, with a dry iron on low heat. Never use steam, keep the iron moving, and test on a scrap first
- Trim thread ends, rub off glue marks and brush the surface. If a spray finish is needed, apply it with the spray gun in a well-ventilated place while wearing a mask
Step 7: Pack and Store
Wrap the trousers in tissue paper and pack them in a cloth garment bag or a box, folded as little as possible. Store them hanging by the waistband in a cool, dry place away from sunlight. A sealed plastic bag traps moisture and causes mould.
Amina, a customer in Mwanza, has a waist of 70 cm, hips of 95 cm and an inside leg of 72 cm. The nearest ready-made pattern is for a waist of 72 cm, hips of 96 cm and an inside leg of 76 cm.
- The hip measurement is within 1 cm, so this size is chosen
- The leg is shortened by 76 - 72 = 4 cm at the shortening line
- The waist is reduced by 72 - 70 = 2 cm, by taking 0.5 cm off each of the four side-seam edges at the waist
- The waistband is cut 70 cm + 4 cm overlap + 2 cm for the two end seams = 76 cm long
Only after these changes is the pattern laid on the leather.
- Wear a dust coat and safety boots, tie back long hair, and wear safety gloves when handling clicking dies and knife blades
- Keep fingers away from the needle, and switch the machine off before threading it or changing a needle
- Cut away from your body and cover the knife when it is not in use
- Use glue and spray finishes with the windows open and away from flames
- Rest the iron on its stand and switch it off after use
- Afterwards, brush dust and threads from the machines, clean glue from brushes and tools, sweep the workplace, and return tools and patterns to their places
- Keep larger leather offcuts for small goods such as key holders. Put scraps, empty glue tins and used rags in the waste bins provided; do not burn leather waste, because the smoke is harmful
- Every needle hole is permanent: check the fit before stitching
- Cut with the leg length parallel to the backbone, and mirror the pieces for left and right
- Use weights, clips and glue, not pins
- Use a leather needle, a long stitch and low, dry heat
A young tailor in Arusha who can make well-fitting leather trousers can take orders from local customers, motorcyclists and visitors. Each pair is made to measure from costly leather, so careful measuring, economical cutting and neat finishing decide whether the business makes a profit and whether customers come back.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to appropriately:
- Take measurements
- Interpret patterns
- Select and prepare tools, equipment, and machines
- Select and prepare leather materials
- Select and prepare fabric materials
- Select and prepare accessories, fitting and reinforcements
- Lay patterns onto leather and trace
- Lay patterns onto fabric and trace
- Lay patterns on sponge foam and trace
- Cut leather
- Cut fabric lining
- Cut foam sponge
- Assemble leather parts using glue
- Assemble fabric lining using glue
- Stitch assembled leather parts
- Stitch fabric lining
- Attach fittings
- Perform ironing
- Perform finishing
- Pack into packing materials
- Observe workshop safety
- Clean tools, equipment and machines
- Clean workplace
- Store tools and equipment
- Store leather trouser
Tathmini ya matokeo
Leather trousers are made according to the required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to make leather trousers
Principles: The student should explain the principles of:
- Adopting readymade patterns
- Laying patterns
- Finishing leather
- Designing trousers
- Operating different tools and machine for making leather trousers
Theories: The student should explain:
- How to interpret patterns
- The structure of leather
- Ironing techniques
- Leather garment technologies
- How to perform routine sewing and sequences when making leather trousers
- Types of accessories and fitting used in the garment industry
- The equipment and machines used in making trousers
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions for garment making
- Safe handling of working tools, equipment and machines
- Waste disposal
Swali
Which tool is used to thin leather edges so that seams and folds lie flat?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado