Mada za sehemu hiiLacing and saddle stitchingMada 4
- Marking the allowances
- Punching chisel
- Performing lacing
- Stitching saddle
When crafting leather goods, an allowance is the extra material added beyond the finished seam or edge. This extra material serves important purposes: it provides space for stitching, allows for folding without damaging the leather, and gives room for joining pieces together neatly. Without proper allowances, a leather project would unravel, tear at the seams, or look unfinished.
Leather workers use four main types of allowances depending on the purpose:
-
Stitching allowance — the space between the edge of the leather and the stitching line, typically 3–5 mm. This is where the needle enters and exits the leather.
-
Fold allowance — the material needed when folding leather back on itself, usually 5–10 mm. Used for creating hems or overlapping edges.
-
Seam allowance — the extra width left on each piece when two pieces are stitched face to face and then turned so that the seam is hidden inside, generally 5–10 mm.
-
Lacing allowance — the distance from the edge to the row of lacing holes, usually about the width of the lace (3–4 mm for a 3 mm lace). The holes are marked at equal intervals a little wider than the lace.
The following tools are used to mark allowances accurately:
- Dividers — the main tool for marking allowances: set the legs to the allowance width, run one leg along the edge of the leather and let the other scribe a line parallel to it; dividers also step off equal spaces for stitch or lacing holes and mark curves
- Marking awl — used to scratch or scribe the allowance line onto the leather surface
- Plough gauge — cuts straps to an even width before the allowances are marked; it has a sharp blade and is a cutting tool, not a marking tool
- Pricking iron or pricking wheel — for marking stitch holes along the allowance line
- Steel ruler — for measuring the required allowance width
- Revolving punch — for punching round lacing holes on the marks
- Clam and bulldog clips — for holding the work
Step 1: Prepare the leather piece Lay the leather flat on the workbench, grain side up. If two layers are to be marked together, hold them with bulldog clips, with a scrap of leather under the jaws so that the clips leave no marks. Ensure the surface is clean and flat.
Step 2: Set the dividers Decide the allowance the job requires, then open the dividers against a steel ruler to that width and tighten the screw. For example, set it to 5 mm for a stitching allowance.
Step 3: Mark the allowance line Rest one leg of the dividers against the edge of the leather and draw the dividers along so that the other leg scribes a light line parallel to the edge. Keep the dividers at the same angle all the way. On a straight edge you can also scribe the line with a marking awl against a steel ruler.
Step 4: Mark stitch holes (if stitching will follow) Place the pricking iron along the marked allowance line. Strike gently to imprint evenly spaced stitch marks. The marks should be 3–4 mm apart for standard stitching. For lacing, step off the hole positions with the dividers and punch them with the revolving punch.
Step 5: Check your marks Before proceeding to cutting or stitching, verify that all allowance lines are consistent in width and parallel to the edge.
Step 6: Position the piece on the clam Place the marked piece between the jaws of the clam with the marked line a little above the jaws, and grip the clam between your knees. Both hands are now free for the awl and needles, and the marked line stays in view.
A student is preparing to stitch two strips of leather together to make a simple belt. Each strip is 25 mm wide.
- Required stitching allowance: 5 mm from each cut edge
- Method: The student sets the dividers to 5 mm, then runs them along each edge of the strip, with one leg against the edge, to scribe the stitching line. Next, using a pricking iron, the student marks stitch holes every 4 mm along this line. When the two strips are placed together and stitched along the marked lines, the stitches will sit neatly 5 mm from the edge — giving a professional, durable finish.
Lacing joins edges by interlocking a narrow leather lace through a row of holes. Each interlocking system uses the holes differently, so decide the style before marking.
- Running stitch — the lace goes in and out along the row; the holes can be further apart
- Whipstitch — the lace passes over the edge and through each hole in turn
- Single loop stitch — each stitch passes under the one before it, covering more of the edge
- Double loop stitch — each stitch passes under the crossing of the two stitches before it, covering the edge completely
Loop stitches wrap the edge more thickly, so they need holes at close, strictly equal intervals and a row that is the same distance from the edge all the way round. New styles are created by changing how the lace interlocks, but accurate allowances remain the base of all of them.
- Wear a dust coat and safety boots; wear safety gloves when handling knives and the plough gauge
- Carry dividers and awls point down and cover the points after use
- Keep the hand that holds the leather behind the cutting edge of any blade
- After work, wipe finished goods with a clean dry cloth, wipe the tools and rub steel parts with a lightly oiled cloth
- Store leather goods and materials flat or loosely rolled in a dry place, and return tools to their rack
- Keep useful offcuts and put useless scraps in the waste bin; do not burn leather waste
- Always measure allowances before marking, not after
- Allowances must be consistent throughout a project for a neat result
- Thicker leather may require larger allowances to accommodate stitching
- Wax the thread with beeswax before stitching: waxed thread grips the leather, resists fraying and lasts longer
- Marking allowances too close to the edge, which weakens the seam
- Inconsistent allowance widths, which causes uneven stitching
- Forgetting to account for the fold when folding leather
In Tanzania, leather artisans in Arusha and Tanga who make Maasai belts, knife sheaths, and sandals use allowance marking daily. When a customer orders a custom leather wallet, the artisan must mark stitching allowances precisely so the wallet holds together after months of use. Without proper allowances, the wallet would split along the seams, costing the artisan both money and reputation.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and materials
- Determine the required allowances
- Position the leather piece on the clam
- Mark allowances
- Observe workshop safety
- Clean leather goods
- Clean tools and equipment
- Store leather goods and materials
- Store tools and equipment
Tathmini ya matokeo
The allowances are marked according to specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to mark the allowances
Principles: The student should explain the principles of:
- Marking the allowances
- Handling handcraft tools
Theories: The student should explain:
- Functions of allowances
- Uses of divider tool
- Different interlocking systems for creating new lacing styles
- The importance of precise and detailed work while marking the allowances
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions while performing marking of allowances
- Safe handling of work tools and machines
- Waste disposal
Swali
Which of the following best describes an allowance in leatherwork?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado