Mada za sehemu hiiOperating meat cutting machinesMada 4
- Operating brisket saw
- Operating splitting saw
- Operating band saw
- Operating a meat slicer
A band saw is a power-driven machine with a continuous toothed blade that cuts bone-in, chilled or frozen meat into uniform pieces quickly. It is also one of the most dangerous machines in a meat plant, so it is operated only by a trained person with every guard in place, and by trainees only under direct supervision.
A band saw uses a long, thin steel blade joined into a loop. The loop runs at high speed around two wheels, one above and one below the table, and the toothed edge passes down through a slot in the table.
- Blade – the toothed steel band that does the cutting
- Upper and lower wheels – carry the blade; the motor drives the lower wheel
- Blade tension handle – raises the upper wheel to tighten the blade
- Blade guides – hold the blade steady above and below the table
- Blade scrapers – wipe fat and bone dust off the blade and wheels
- Adjustable blade guard – covers the blade above the meat; it is lowered until only the part of the blade needed for the cut is exposed
- Wheel doors – cover the wheels and the rest of the blade
- Fixed table and sliding carriage – carry the meat past the blade
- Thickness gauge – a plate set at a chosen distance from the blade to control the thickness of each cut
- Pusher plate – holds and pushes small or end pieces so that fingers stay away from the blade
- On/off switch and emergency stop – start and stop the machine
Models differ, so follow the manufacturer's manual for your machine. Its rating plate shows the voltage and whether it needs a single-phase or three-phase power supply.
- Wear a cap or helmet that covers the hair, a clean close-fitting overall and gumboots with non-slip soles.
- Remove watches, rings and bracelets, and have no loose sleeves or strings.
- Do not wear loose gloves, including metal-mesh gloves, while feeding meat to the blade. The teeth can catch a glove and drag the hand in.
- Set out the aluminium table for the meat waiting to be cut and for the finished cuts, with hooks, a knife, the steriliser and the washing basin close by.
- Wash your hands, sterilise the knife and hooks, and have a pen and notebook ready for records.
Meat for the band saw must be well chilled (about 0–4 °C): firm meat cuts cleanly, while warm, soft meat drags on the blade. Move the carcass or quarter from the chiller along the overhead rail on its hook; do not carry heavy quarters alone. Use the knife to break it into pieces that fit the saw table and place them on the aluminium table. Bring out only as much as you can cut in a short time, so that the meat stays cold, and never let meat touch the floor.
Step 1: Check the machine with the power off
- Make sure the saw is switched off and isolated from the power supply.
- Check that the blade is sharp, undamaged, correctly tensioned and running in its guides, with the teeth pointing down towards the table.
- Check that the scrapers, wheel doors and all guards are in place and secure.
- Check that the cable, plug and switch are undamaged and dry, and that the floor is dry and clear.
Step 2: Set up and start
- Set the thickness gauge to the required thickness.
- Lower the blade guard to just above the height of the meat.
- Connect the power, stand firmly balanced, switch on and let the blade reach full speed.
Step 3: Cut the meat
- Place the meat with its flattest side down on the carriage, against the thickness gauge.
- Push the carriage forward slowly and steadily. Let the blade do the cutting; never force the meat.
- Keep your hands to the side of the blade, never in line with it, with fingers together and thumbs tucked in.
- Use the pusher plate for small pieces and for the last part of every piece. Never hold a small or round piece by hand.
- Never reach across or behind the running blade.
Step 4: Stop
- Switch off and wait until the blade has stopped completely before clearing cut pieces or leaving the machine.
- If the blade jams, breaks or makes an unusual noise, press stop, wait for the blade to stop and isolate the power before touching anything. Report the fault.
- Switch off, wait for the blade to stop, and isolate the machine by unplugging it or switching off the isolator. Never clean a saw that is still connected to the power.
- Release the blade tension, open the doors and lift the blade off carefully. Wear cut-resistant gloves to handle the loose blade.
- Remove the scrapers, guides and table parts, scrape off meat, fat and bone dust, and wash all parts and the inside of the cabinet with hot water and detergent.
- Rinse with clean water, apply a food-safe sanitiser and leave to air-dry. Do not spray water on the motor or switch.
- Reassemble, replace the guards, and put bone dust and scraps in the covered waste bin.
- Change the blade when it is blunt, cracked or has missing teeth; a blunt blade needs more pushing force, which causes accidents.
- Lubricate only the points named in the manual, using food-grade grease.
- Leave electrical repairs to a qualified electrician.
Write down, with the date and your name:
- Production – the type and weight of meat cut and the number of portions
- Temperature – the temperature of the chiller or the meat
- Cleaning – when the saw was cleaned and sanitised
- Maintenance – blade changes, faults reported and repairs
A butcher's shop in Dar es Salaam needs 20 kg of chilled bone-in beef cut into 2 kg portions.
- The operator puts on her safety gear and, with the power isolated, checks the blade, guides, scrapers and guards.
- She sets the thickness gauge, lowers the blade guard, connects the power and starts the saw.
- She cuts the first piece, weighs it, and adjusts the gauge until a piece weighs about 2 kg.
- She cuts the rest, using the pusher plate for each end piece, to give 10 portions.
- She switches off, isolates the power, then strips, washes and sanitises the saw.
- She records the weight cut, the number of portions and the cleaning.
- Never operate the band saw without training, supervision and all guards in place
- Keep hands out of the line of the blade and use the pusher plate
- No loose clothing, jewellery or loose gloves near the moving blade
- Isolate the power before clearing a jam, changing a blade or cleaning
In Tanzania, butchers' shops and meat processing plants use band saws to cut large bone-in pieces into smaller portions that families can afford to buy. An operator who sets the gauge correctly, keeps the guards in place and cleans the saw properly produces neat, equal portions with little waste, protects customers from contaminated meat, and works without injury.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Organize work tools, equipment and safety gear
- Bring the chilled carcass
- Identify parts of the band saw
- Operating band saw
- Keep different records
- Clean the band saw after the uses
Tathmini ya matokeo
The band saw correctly operated as per instructions
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The students should explain how to operate band saw
Principles: The students should explain the principle of operating band saw
Theories: The students should explain procedures involved in:-
- How to handle the band saw
- Identify parts of band saw
- Procedures of operating band saw
- Maintaining the band saw
Circumstantial knowledge:
Detailed knowledge about:
- Meat handling
- Power supply
- Model of the machine
Swali
Meat for the band saw is chilled to about 0–4 °C. How does this help the cutting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado