Mada za sehemu hiiProcessing inedible slaughter by-productsMada 3
- Processing tail switch, hooves and horns
- Processing hides and skins
- Preparing blood and bone meal
Processing Hides and Skins
Processing hides and skins is the series of steps that transform raw animal hides and skins into usable materials, primarily leather. This involves cleaning, preserving, and treating the raw material to prevent spoilage and prepare it for further industrial processing. In Tanzania, hides and skins from cattle, goats, and sheep are valuable by-products of the slaughtering industry.
Proper processing of hides and skins contributes to:
- Economic value addition – Raw hides become valuable leather for shoes, bags, and belts
- Waste reduction – By-products that would otherwise be discarded gain economic value
- Job creation – Leather processing supports artisans and tanneries
- Export opportunities – Quality hides and skins can be sold to local and international markets
The following tools and equipment are used in processing hides and skins:
- Flaying knives and skinning knives
- Sharpening steel or oil stone
- Ropes and twine
- Frames (wooden or metal) for stretching
- Buckets and clean water
- Spades
- Protective gear (white coats, aprons, gumboots, masks, industrial caps)
Before curing, hides and skins must be properly prepared to ensure good quality end products.
Flaying
Flaying is the careful removal of the hide or skin from the carcass after bleeding. The hide must be removed without causing damage. Common flaying defects include:
- Deep cuts
- Gouge marks
- Scores
Washing
Wash the hides or skins with clean water immediately after flaying, before the blood coagulates. This removes dirt, blood, and other contaminants.
Trimming
Trim off useless portions to give the hide or skin a good, uniform shape. This makes handling easier and improves the final product quality.
Fleshing and Defatting
Fleshing involves removing flesh, fat, and connective tissue from the hide. This is done on a specially prepared "beam" – a curved wooden or metal surface. Excess fat is commonly found on the tail area and the hump. Clean hides may not require fleshing, as chances of cuts are higher during this operation.
Lacing
Lacing involves stretching and securing the hide to a frame or loop using string or fibres. Holes should be made as small as possible to prevent tearing during stretching.
Curing is the process of preserving hides and skins to prevent bacterial growth and decay. Two main methods are used: drying and salting.
Drying Methods
Sun-Drying (Ground or Hung)
This is a traditional, cost-effective method that requires appropriate weather conditions.
Procedure:
- Prepare the hide by removing flesh and fat
- Clean with clean water
- Stretch the hide to prevent shrinking
- Place in direct sunlight, turning every few hours for even drying
- Drying takes 2–7 days depending on weather and hide thickness
- Store in a cool, dry place when completely dry
Suspension Drying (Frame Drying)
A frame is used to stretch the hide, allowing air circulation on all sides. This ensures even drying and prevents stiffness or deformation.
Frame dimensions:
- Large breeds (cattle): 2.75 m × 3 m (9 ft × 10 ft)
- Smaller breeds (sheep, goats): 2.75 m × 2.5 m (9 ft × 8 ft)
Frames should be arranged east-west facing the sun, with at least 30 cm spacing between frames for air circulation. Average drying time is about 7 days.
Procedure:
- Clean the hide and rinse with water
- Scrape off remaining flesh or fat
- Stretch the hide tightly over the frame
- Secure edges with rope or nails
- Hang in a well-ventilated, sunny location
- Allow 7 days for complete drying
- Store in a cool, dry place
Shed Drying
Similar to frame drying but performed in a well-ventilated roofed structure. This protects hides from rain, direct sun, insects, and contamination.
Salting Methods
Salting draws moisture out of hides and prevents bacterial growth, mould, and decay.
Wet Salting Technique
- Spread hide on floor or wooden pallet
- Apply common salt at 30–40% of the green weight on the flesh side
- Stack additional hides with flesh side up, applying salt to each
- Allow brine to drain for 5 days
- Remove extra salt and keep grain side clean
- Pile must be on pallets 15 cm above ground for airflow
Dry Salting Method
This combines drying and salting advantages. The procedure is similar to wet salting but uses 10% less salt. After brine dries, hides can be hung on wires or ropes to complete drying. This method is especially suitable for export stock.
Brining Method
- Soak fleshed and washed hides in saturated salt solution (33%) for 24 hours
- Restore brine by adding fresh salt as water dilutes it
- Remove hides and pile to drain
- Apply wet salting using 20% salt by weight
- Tent method: Hang hide on wire, spread sides with rope/pegs in tent shape, flesh side up
- Parasol method: Hang on single pole, spread sides like a conical tent
- Hanging on wires/ropes: Hang flesh side up, separate sides with small twigs
A livestock farmer in Mwanza who slaughters cattle for beef can process the hides using frame drying instead of throwing them away. After flaying, washing, and stretching the hide on a simple wooden frame built from local timber, the dried hide can be sold to local tanneries or artisans for around TZS 15,000–25,000 per piece, adding extra income to the meat sales and utilizing what would otherwise be waste.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select work tools, equipment, machines and safety gears
- Maintain hygiene of processing area
- De flesh and de fat hides and skins
- Perform salting of hides and skins
- Store hides and skins
- Keep different records
- Clean tools, equipment used and work place
- Store tools and equipment
Tathmini ya matokeo
Hides and skins processed according to the required standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should be able to explain how to process hides and skins
Principles: The student should outline principles involved in processing hide and skin
Theories: The student should:
- List down the procedures involved in processing hide and skin
- Explain how to perform lacing of hides and skins
- Elaborate how to cure hides and skins
- Elucidate how to perform defleshing and defatting
- Describe defleshing and defatting
- Explain how to maintain hygiene of hides and skin sheds
- Elaborate how to handle and store cured hides and skin
- Explain how to control pests
- Highlight the importance of keeping different records Circumstantial
- Environmental issues
Swali
Which of the following tools is NOT used in processing hides and skins?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado