Mada za sehemu hiiExecuting forest harvestingMada 3
- Interpreting harvesting plan
- Determining the extraction route
- Preparing landing site
Determining the Extraction Route
When trees are felled in a forest, the logs must be moved from the felling site to a collection point, loading area, or sawmill. The extraction route is the path chosen for moving logs out of the forest. Selecting the correct route makes extraction easier, safer, and causes less damage to the remaining trees and forest floor.
In this lesson, you will learn what an extraction route is, how to mark it using pegs, how to measure the slope of the route, and how to decide which route is most suitable for extraction.
An extraction route is a prepared path along which logs are pulled or transported from the felling site to a road or collection point. The route should:
- Be as short as possible to save time and effort
- Have a gentle slope (not too steep) so that logs can be moved safely
- Avoid obstacles such as large stumps, rocks, or soft muddy areas
- Pass through areas where remaining trees will not be badly damaged
Before extraction begins, the route must be planned and marked clearly so that workers follow the same path.
Pegs are wooden stakes driven into the ground to mark the centre line of the extraction route. Aligning pegs helps workers see the path clearly.
Steps to Align Pegs
-
Identify the start point – This is where the logs are piled after felling (the landing area).
-
Identify the end point – This is where the logs will be loaded onto a truck or taken to the road (the collection point).
-
Walk between the two points and choose the most suitable ground. The route should avoid steep slopes and soft ground.
-
Drive the first peg at the start point.
-
Drive additional pegs at regular intervals (for example, every 5 to 10 metres) along the chosen path, making sure each peg is in a straight line with the ones before and after it.
-
Check the alignment by sighting from one peg to the next. All pegs should appear in a straight line.
Pegs make the route visible to everyone working in the forest and help prevent workers from wandering off the planned path.
The slope (or gradient) of the route is important because very steep slopes are dangerous for log extraction and can cause accidents.
How to Measure Slope Using a Clinometer
A clinometer is an instrument used to measure the angle of a slope.
-
Set up the clinometer at the first peg.
-
Sight along the clinometer towards the next peg (or a helper holding a marker at the next peg).
-
Read the angle shown on the clinometer. This is the slope angle in degrees.
-
Record the slope for each section of the route.
Interpreting the Slope
- 0° to 10°: Gentle slope – safe and easy for extraction
- 10° to 20°: Moderate slope – extraction is possible but requires care
- Above 20°: Steep slope – dangerous for extraction; an alternative route should be chosen
A practical example: If the slope angle measured between two pegs 10 metres apart is 8°, this is a gentle slope suitable for extraction. If the angle is 25°, the route is too steep and another path should be found.
After marking the route with pegs and measuring the slope, you must decide whether the route is suitable or if changes are needed.
Decision Checklist
- Are all pegs in a straight line?
- Is the slope gentle enough (less than 20°)?
- Does the route avoid obstacles?
- Is the route as short as possible?
- Will the route cause minimal damage to the forest?
If the answer to any of these questions is "no," adjust the route by moving the pegs and re-measuring the slope until a satisfactory route is found.
Example of Choosing a Route
Suppose there are two possible paths from the landing area to the road:
- Route A is 80 metres long with an average slope of 6°.
- Route B is 60 metres long but has an average slope of 22°.
Route A is the better choice because the slope is safe for extraction, even though it is longer. Route B is shorter but too steep and would be dangerous.
When determining an extraction route, always follow safety rules:
- Wear protective clothing: overalls, safety boots, safety helmet, and gloves
- Work in groups – never work alone in the forest
- Check the area for hazards such as dead trees, insects, or uneven ground
- Keep a first aid kit nearby
- Use proper tools such as hoes and shovels to clear the route
In Tanzania, small-scale timber traders in areas like Morogoro or Shinyanga often buy standing trees from forest owners, fell them, and transport the logs to sawmills. When harvesting timber from a bush plot, a farmer or logger must plan a route to drag logs out to the nearest road. Using pegs to mark the path and a simple slope check helps avoid choosing a route that is too steep or muddy, which could cause the truck to get stuck or the logs to roll dangerously. This skill saves time, reduces labor costs, and prevents accidents during the dry season when many logging activities take place.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Identify extraction routes
- Align pegs along the extraction route
- Measure slope of extraction route
- Determining extraction route
- Observe safety
- Clean tools
- Store tools
Tathmini ya matokeo
Extraction routes determined as per standards
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The students should explain how to:
- Determine extraction routes
- Apply safety precautions while preparing extraction route
Principles: The student should explain procedures involved in preparing extraction routes
Theories: The student should explain the extraction route
Detailed knowledge about: Safety precautions while preparing extraction routes
Swali
What is an extraction route in forest harvesting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado