Mada za sehemu hiiReceiving timber and poles for treatmentMada 3
- Measuring dimensions
- Classifying timber according to species
- Recording dimensions
Measuring the dimensions of wood is essential before any treatment process because accurate measurements determine how much preservative is needed and ensure effective protection against wood-destroying organisms.
Timber dimensions refer to the specific measurements and sizes of wood used in construction and woodworking. For sawn timber, the dimensions include length, width, and thickness. For poles, the dimensions include diameter and length.
Knowing these dimensions is important because:
- Accurate measurements help determine the amount of treatment required
- They ensure even application of preservatives for effective protection
- Thicker wood may need deeper penetration treatments
- They allow precise calculation of surface area needing treatment
Three main tools are used:
- Callipers – measure the diameter of standing trees; held perpendicular to the tree trunk
- Diameter tape – wrapped around the tree to measure circumference, which is converted directly to diameter
- Tape measure – used for measuring length of felled trees and sawn timber
Height of a Standing Tree
The height of a standing tree is the vertical distance from the base to the tip of the highest branch. Two common methods are:
Shadow Method
This method uses similar triangles. The ratio of your height to your shadow equals the ratio of the tree's height to the tree's shadow.
The formula is:
Tree height (T)=Your shadow (Y)Your height (H)×Tree shadow (S)
Worked Example 1.1
Your height (H) = 1.5 m, your shadow (Y) = 2.5 m, tree shadow (S) = 33.5 m
Solution:
Tree height=2.51.5×33.5=2.550.25=20.10 metres
Stick Method
This uses a stick placed vertically near the tree:
Tree height=Stick shadowStick height×Tree shadow
Worked Example 1.2
Stick height = 1.0 m, stick shadow = 0.5 m, tree shadow = 5 m
Solution:
Tree height=0.51.0×5=2×5=10 metres
Diameter at Breast Height (DBH)
DBH is measured at 1.3 metres from ground level. It is measured using callipers or diameter tape and expressed in centimetres. Callipers are placed on either side of the trunk, perpendicular to the tree axis.
Length of a Felled Tree
The length is the straight-line distance from the base to the tip. A measuring tape is used, measuring from one end to the other.
Timber has three key dimensions:
- Thickness – varies depending on type (plank = 2 inches, board = 1 inch)
- Width – how wide the timber is across its face
- Length – measured in feet or metres
Common Sawn Timber Sizes
| Type | Thickness | Common Widths |
|---|---|---|
| Plank | 2 inches (50 mm) | 50×50 mm, 50×75 mm, 50×100 mm, 50×150 mm, 50×200 mm |
| Board | 1 inch (25 mm) | 25×150 mm, 25×200 mm, 25×250 mm, 25×300 mm |
Note: Nominal thickness is the rough size when first cut; actual thickness is after drying and planing.
In Tanzania, Eucalyptus species are commonly used for electricity transmission poles. Poles are classified by length and class:
| Pole Class | Length (m) | Min. Top Diameter (mm) |
|---|---|---|
| Light | 9-10 | 130-150 |
| Medium | 9-14 | 150-190 |
| Intermediate | 10-14 | 180-210 |
| Stout | 10-18 | 200-245 |
When measuring tree diameters in the field:
- Select trees carefully, wearing appropriate PPE
- Measure at breast height (1.3 m from ground)
- Use callipers perpendicular to the tree axis
- Read the diameter from the scale in centimetres
- Record measurements in a notebook
Accuracy tips:
- Ensure callipers are not bent
- Measure on flat ground
- Avoid snakes and insects in the area
In Tanzania, measuring wood dimensions is directly applied when local carpenters or construction workers select timber for building houses or furniture. For example, a furniture maker in Dar es Salaam must measure the width and thickness of planks (such as 50 mm × 150 mm) to calculate how many pieces are needed for a bed frame, ensuring the wood can support weight without waste. Similarly, Tanzania Electricity Supply Company (TANESCO) workers must verify that eucalyptus poles meet the required diameter and length specifications before installing them as electricity transmission poles.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment for measuring dimensions of wood for treatment
- Measure dimensions of wood
- Adhere to safety precautions
- Clean and store materials and equipment
- Store tools
Tathmini ya matokeo
Dimensions of wood for treatment measured as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain how to:
- Use tools to maintain tally cards
- Measure dimensions of wood
Principles: The student should explain procedures involved in measuring dimensions of wood for treatment
Theories: The student should explain importance of:
- Measure timber and poles dimensions
- Keeping records of timber and poles
Detailed knowledge about: Safety precautions involved in measuring dimensions of wood for treatment
Swali
Which tool is used to measure the diameter of a standing tree at breast height?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado