Mada za sehemu hiiPreparing poles and sawn timber for treatmentMada 4
- Debarking poles
- Preventing end splits of poles
- Determining moisture content of the pole and sawn timber
- Testing strength of poles
Determining Moisture Content of Pole and Sawn Timber
When a tree is first cut, the wood contains a large amount of water — sometimes up to half of its weight. This water is called moisture content. Freshly cut wood can have moisture content from 30% to more than 60%. The moisture content must be reduced before the wood can be used for building or making furniture.
Wood is easier to use when it has about 25% moisture remaining. This point is called the Fibre Saturation Point.
The oven-dry method is a standard way to find the exact moisture content of wood. This method involves drying a wood sample in an oven and comparing its weight before and after drying.
Steps of the Oven-Dry Method
- Select wood samples and ensure they are free from bark and defects.
- Cut the samples into standard sizes.
- Use a weighing balance to measure the initial weight (W₁) of each wet sample. Record this weight.
- Set the oven to the required temperature and place the wet samples inside.
- After the drying time is complete, remove the samples using tongs (they will be very hot).
- Measure the dry weight (W₂) of each sample using the weighing balance. Record this weight.
- Use the formula below to calculate the moisture content.
Formula for Moisture Content
M.C=W2W1−W2×100
Where:
- M.C = Moisture content in percentage (%)
- W₁ = Weight of wet wood (before drying)
- W₂ = Weight of dry wood (after drying)
Worked Example
A student tested a wood sample for moisture content. The wet weight of the sample was 115 kg, and after drying in the oven, the weight was 100 kg. Calculate the moisture content.
Solution:
M.C=100115−100×100
M.C=10015×100
M.C=15%
Therefore, the moisture content of this wood sample is 15%.
Removing moisture from wood is called seasoning. Timber is seasoned to make it suitable for use. Different uses require different moisture levels:
- 18–24% for caressing timber (structural purposes)
- 7–16% for internal joinery (furniture and fixtures)
Air Seasoning
Air seasoning (also called natural seasoning) involves stacking poles or timber outdoors to allow natural air circulation to gradually remove moisture. In Tanzania, this method takes more than 3 months to 1 year, depending on:
- Pole type
- Temperature
- Humidity
- Size of the wood
Advantage: It is relatively cheaper and can handle larger stocks of wood.
Kiln Drying
Kiln drying uses a special oven called a kiln that controls temperature, humidity, and airflow. This method dries wood quickly and carefully over several days or weeks.
Advantages:
- Faster than air drying
- Gives consistent and uniform results
- Better quality control
Wood is stacked with spacers in the kiln to allow air to flow around each piece.
Dried timber has several advantages over green (wet) timber:
1. Resistance to Decay and Insect Damage
Dried timber has low moisture content. Fungi and termites cannot survive in dry wood. This helps structures last longer and reduces maintenance costs.
2. Improved Insulation and Thermal Properties
Dried wood has better insulation properties due to its low moisture content. It helps keep buildings warmer during cold seasons, improving energy efficiency.
3. Increased Strength and Stability
Dried timber is stronger than green wood. It is less likely to warp, split, or bend under stress. This makes it reliable for construction and furniture making.
4. Enhanced Penetration of Preservatives and Finishing Products
Dry wood absorbs preservatives, paints, stains, and sealants more effectively than wet wood. This improves protection against moisture and UV damage, and finishes last longer.
In Tanzania, builders and carpentry workshops use the oven-dry method or moisture metres to check timber before starting a project. For example, a furniture maker in Dar es Salaam must ensure the timber has dried to about 12% moisture before making wardrobes or tables; otherwise, the furniture may warp and crack as it dries further, leading to customer complaints and financial loss.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment for determine moisture content
- Determine moisture content in poles and sawn timber
- Remove moisture content in poles and sawn timber
- Adhere to safety precautions
- Clean and store materials and equipment
- Store tools
Tathmini ya matokeo
Moisture content of the pole and sawn timber determined as per specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain how to:
- Select tools and equipment for determining moisture content
- Determine moisture content
- Remove moisture content
- Apply safety precautions when debarking
Principles: The student should explain procedures involved in determining moisture content of the pole and sawn timber
Theories: The student should explain the importance of determining moisture content of the pole and sawn timber
Detailed knowledge about: Safety precautions involved in determining the moisture content of the pole and sawn timber
Swali
What is meant by the term "moisture content" in wood?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado