Mada za sehemu hiiRepairing saw bladesMada 3
- Repairing cracks in saw blades
- Removing lumps in saw blades
- Removing depressions in saw blades
Removing Lumps in Saw Blades
A lump is a raised spot on the flat surface of a saw blade. Lumps are caused by excessive heat. When the saw blade rubs against the wood during cutting, friction generates heat that causes the metal to expand and push outward, forming lumps. These lumps can be round, long, or spiral in shape. Lumps make the saw blade cut unevenly, cause vibration, and reduce the quality of sawn timber. It is important to remove lumps through a process called levelling, which restores the blade to a flat, even surface.
The following tools are used to remove lumps and depressions from saw blades:
- Dog-head hammer – A hammer with a rounded, crowned face (weighs about 1.8 kg), used for tensioning circular saws. Its convex striking surface helps expand the metal evenly.
- Cross-face hammer – Has one face parallel to the shaft and another perpendicular. Used to hammer out crosswise and lengthwise lumps on both circular and band saws.
- Twist-face hammer – Weighs about 1.8 kg, with the face set at a 45-degree angle to the shaft. Used for levelling and removing twists in the saw body.
- Hammering bench – A sturdy bench that supports the saw blade during hammering.
- Anvil – A block of steel with a convex surface, weighing 45 kg to 300 kg, used for levelling and tensioning.
- Straight edges – Long and short flat pieces of metal used to check for lumps and depressions.
- Mould edge – A flat steel piece with one straight edge, used to check blade level and tension uniformity.
- Chalk – Used for marking lump locations and hammering patterns.
- Cotton cloth – Used for cleaning the saw blade before and after work.
The following steps outline how to remove lumps and depressions from a band saw blade:
- Mount the saw blade – Secure the saw blade into a roller saw stretcher machine.
- Lift the blade – Use your left hand to lift the blade for inspection.
- Hold the mould edge – Grip the mould edge in your right hand and keep it perpendicular to the blade.
- Mark the faults – Identify and mark the lumps and depressions using chalk.
- Remove large faults – Use the roller stretcher machine to remove bigger depressions and lumps by rolling.
- Remove small lumps – Use the cross-face hammer with thin leather or thick paper placed between the saw blade and anvil. This prevents the blade from stretching too much.
- Check the blade – Reinspect using the mould edge to confirm the surface is flat and ready for use.
The following steps describe how to remove lumps from a circular saw blade:
- Clean the saw blade – Remove dust, resin, and gums from the teeth and saw body using a rag or cotton cloth.
- Position the blade – Hold the saw blade against the bench to reduce movement and give better control.
- Check along the diameter – Use a long straight edge to check the saw blade along the diameter.
- Check along the radius – Use short straight edges to check along the radius from the centre to the edge.
- Mark fault areas – Clearly mark the locations of lumps and depressions with chalk.
- Hammer the lumps – Place the blade on the anvil and carefully hammer the raised areas using appropriate hammers (dog-head or cross-face hammer).
- Repeat on both sides – Perform the same procedure on both sides of the saw blade.
- Clean and store tools – Place hammers, straight edges, and other tools neatly after finishing.
Suppose a circular saw blade has a visible lump near the edge. The technician follows these steps:
- Cleans the blade thoroughly with cotton cloth to remove sawdust and resin.
- Places a long straight edge across the blade diameter. A gap appears at the lump location.
- Marks the lump with chalk.
- Places the blade on the anvil with the lump facing up.
- Uses the cross-face hammer to lightly strike around the lump area, working from the outside toward the centre of the lump.
- Checks again with the straight edge to confirm the lump is removed.
- Repeats the process on the other side of the blade.
- Wear leather gloves, safety boots, a helmet, and overalls when handling saw blades.
- Be careful with the sharp cutting edges of the blade.
- Ensure the blade is properly secured before hammering.
- Keep the work area clean and organized.
In Tanzania, a sawmill operator in Mbeya or Mwanza relies on properly maintained saw blades to produce high-quality timber for furniture and construction. When a saw blade develops lumps from excessive heat during continuous cutting of hard timber like mvule or mtumbatu, the operator must use the levelling techniques learned in this topic to restore the blade's flatness. This prevents costly blade replacements and ensures smooth, accurate cuts that fetch better prices at local markets like Mlimani City or general markets countrywide.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Check lumps in saw blade
- Remove lumps in saw blades
- Adhere to safety
- Clean and store materials and
- Store tools
Tathmini ya matokeo
Lumps in saw blades - Select tools and blades removed as per specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The student should explain how to:
- Select tools and equipment
- Remove lumps in saw blades
- Adhere to safety
Principles: The explain the principles of removing lumps on
Theories: The importance of
Circumstantial knowledge:
Detailed knowledge about: Safety precautions involved in removing lumps in saw blades.
Swali
What causes lumps to form on a saw blade?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado