Mada za sehemu hiiInstalling compression system refrigerant control circuitsMada 3
- Building controls based on temperature change
- Building controls based on pressure change
- Building controls based on volume or quantity changes
Pressure-based control circuits regulate the flow of refrigerant in a refrigeration or air conditioning system by monitoring and responding to pressure changes within the system. These controls ensure that the correct pressure is maintained at all times, preventing equipment damage and ensuring efficient cooling.
Pressure-based control circuits are systems that use pressure sensors or gauges to monitor pressure levels in the evaporator, condenser, and refrigerant lines. When pressure goes above or below the desired range, the control system automatically adjusts the refrigerant flow to bring it back to normal.
Unlike temperature-based controls that respond to heat changes, pressure-based controls respond directly to the force exerted by the refrigerant. This makes them particularly useful in large-scale refrigeration systems where pressure fluctuations can indicate serious problems.
Pressure-based control circuits offer several important benefits:
- Prevents pressure fluctuations — Keeps the system running smoothly by stopping sudden pressure changes that could damage components.
- Fewer moving parts — Compared to electronic control systems, pressure controls are simpler and require less maintenance.
- Suitable for large systems — Ideal for commercial refrigeration, process cooling, and HVAC systems that need consistent pressure control.
- Reduces compressor cycling — Minimizes unnecessary starts and stops of the compressor, which saves energy and extends the life of the equipment.
The system works by continuously measuring pressure at critical points:
- Pressure sensors or gauges measure pressure in the evaporator, condenser, and refrigerant lines.
- The control system compares the measured pressure with the set limits.
- If pressure rises too high — A high-pressure regulator reduces refrigerant flow to prevent dangerous buildup.
- If pressure drops too low — A low-pressure regulator allows more refrigerant into the evaporator to restore proper balance.
- The regulators work together to keep the system within safe operating conditions.
Materials and Tools Required
- Pressure Regulating Valve (PRV)
- High-pressure and low-pressure regulators
- Copper refrigerant tubing
- Evaporator coil and condenser coil
- Compressor
- Receiver and filter drier
- Pressure sensors and gauges
- Refrigerant (R-134a, R-410A, or system-specific)
- Tube cutter and tube bender
- Brazing torch and silver brazing rods
- Adjustable wrenches and flaring tool
- Vacuum pump
- Manifold gauge set
- Leak detector
- Digital thermometer
- Refrigerant scale
- Safety goggles, boots, and overall
Procedure Steps
- Identify locations for the high-pressure and low-pressure regulators, PRV, and pressure sensors.
- Mount the compressor securely with vibration isolators.
- Position the condenser coil in a well-ventilated area for efficient heat dissipation.
- Connect refrigerant piping between the compressor and condenser.
- Install the PRV in the liquid line before the evaporator to regulate refrigerant pressure.
- Use flare or brazed fittings to ensure a secure connection.
- Install a high-pressure regulator on the discharge line to prevent excessive pressure buildup.
- Install a low-pressure regulator before the compressor inlet to maintain minimum operating pressure.
- Install pressure sensors at critical points such as the compressor discharge, evaporator inlet, and suction line.
- Use copper tubing to connect the components, ensuring smooth refrigerant flow.
- Pressurize the system with dry nitrogen and check for leaks using a leak detector.
- Evacuate the system using a vacuum pump to remove moisture and air contaminants.
- Connect the refrigerant cylinder and charge the system.
- Monitor pressure gauges to ensure the system reaches the correct operating pressure.
- Start the system and observe pressure fluctuations in the evaporator and compressor.
- Adjust the PRV and pressure regulators to maintain stable operation.
- Check for steady pressure regulation and consistent cooling performance.
A small cold room at a fish processing plant in Mwanza is experiencing inconsistent cooling. The technician installs a pressure-based control circuit with a high-pressure regulator set at 250 psi and a low-pressure regulator set at 50 psi. When the compressor runs, the pressure sensors read:
- Evaporator pressure: 45 psi (below the 50 psi set point)
- Condenser pressure: 240 psi (within safe range)
The low-pressure regulator detects that the evaporator pressure has dropped below the set point. It automatically opens to allow more refrigerant into the evaporator. After a few minutes, the evaporator pressure rises to 55 psi, and the regulator closes. The system now maintains stable temperatures between -5°C and 0°C, suitable for storing fresh fish.
In Tanzania, a restaurant owner in Arusha uses a medium-sized cold room to store fresh meat and vegetables. When the pressure-based control circuit detects that the refrigerant pressure has dropped too low (indicating the evaporator is not receiving enough refrigerant), the low-pressure regulator automatically allows more refrigerant to flow. This keeps the cold room at the correct temperature of 0°C to 4°C, preventing food spoilage and saving the business from losing thousands of shillings in damaged stock.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment and safety gears
- Interpret working drawing
- Test function of control components
- Mount refrigerant controls at appropriate locations of the system
- Charge system with refrigerant
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
Refrigerant controls are installed as per technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain different ways of installing refrigerant controls
Principles: The student should explain the principle of: (c) Controls based on temperature changes (d) Controls based on pressure changes (e) Controls based on volume or quantity changes
Theories: The student should explain:
- Gas laws
- Super heating and sub-cooling process
- Flash gas and heating refrigerant operations
- Equalizer operations
Circumstantial knowledge:
Detailed knowledge about:
- Plumbing work
- Environmental regulation
- Refrigerant safety regulations
Swali
What is the primary function of pressure-based control circuits in a refrigeration system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado