Mada za sehemu hiiRepairing cold roomsMada 6
Refrigerant pipes are the pathways that carry refrigerant gas between the compressor, condenser, evaporator, and other components in a refrigeration or air conditioning system. When these pipes develop leaks, blockages, or damage, the system loses its cooling ability and must be repaired to restore proper operation.
Refrigerant pipes are narrow copper or aluminum tubes that circulate refrigerant through the closed-loop system. They connect the major components and allow the refrigerant to change from gas to liquid and back, enabling heat absorption and rejection. In cold rooms and industrial AC systems, these pipes can suffer damage from vibration, corrosion, physical impact, or improper installation.
- ** refrigerant leaks** — small holes or cracks caused by corrosion, vibration, or accidental damage
- Blockages — dirt, moisture, or debris restricting refrigerant flow
- Kinks or dents — restricting the pipe diameter and reducing efficiency
- Loose connections — fittings that have become loose over time
Before repairing refrigerant pipes, gather the following tools:
- Oxy-acetylene welding set for brazing
- Flaring and swaging tool kit for making connections
- Manifold gauge for pressure testing
- Vacuum pump for removing moisture
- Recovery cylinder and unit for proper refrigerant handling
- Multimeter and digital clamp meter for electrical checks
- Piecing plier and pinch-off tools
- Safety goggles, gloves, safety boots, and overall
- Always wear personal protective equipment (PPE) including goggles, gloves, and boots
- Recover refrigerant properly using a recovery unit before opening the system
- Ensure the system is isolated and powered off before beginning repairs
- Work in a well-ventilated area when using welding equipment
- Use ladder safely when working on elevated pipes
Step 1: Diagnose the Problem
Use the manifold gauge to check system pressures. Low pressure on the low-side and high-side indicates a refrigerant leak. Listen for hissing sounds and use leak detection solution to locate the exact leak point.
Step 2: Recover the Refrigerant
Connect the recovery unit to the system and recover the refrigerant into a recovery cylinder. This is required by environmental regulations as refrigerants are harmful to the ozone layer.
Step 3: Prepare the Damaged Area
Clean the damaged pipe section thoroughly. For small leaks, you may use a repair clamp. For larger damage, cut out the damaged section using a pipe cutter.
Step 4: Repair or Replace the Section
Use the flaring and swaging tool to prepare new pipe sections. Connect using proper fittings and braze with the oxy-acetylene welding set. Ensure the brazed joint is strong and leak-free.
Step 5: Pressure Test and Evacuate
After repair, connect the manifold gauge and pressurize the system with nitrogen to test for leaks. If no leaks are found, use the vacuum pump to evacuate the system to remove moisture and air.
Step 6: Charge with Refrigerant
Weigh the correct amount of refrigerant using a charging scale and charge the system according to the manufacturer's specifications.
A small cold room in a Dar es Salaam fish market has developed a refrigerant leak in the suction line between the evaporator and compressor. The technician:
- Connects the manifold gauge and reads 30 psi on the low side (normally 70-80 psi)
- Applies leak detection solution and identifies bubbles near a corroded section
- Recovers 2.5 kg of R-404A refrigerant into the recovery cylinder
- Cuts out 15 cm of damaged copper pipe
- Flares both ends and connects a new pipe section using flare fittings
- Pressurizes with nitrogen to 150 psi — no pressure drop after 30 minutes
- Evacuates to 500 microns for 30 minutes
- Recharges with 2.5 kg of R-404A as specified on the nameplate
The system now operates at correct pressures and maintains the cold room at -18°C.
In Tanzania, cold rooms are essential for preserving fish, vegetables, and medicines. A technician at a local market in Mwanza or Arusha uses these repair skills to fix leaks in small cold rooms that store fresh fish. By properly repairing refrigerant pipes, the technician helps business owners avoid losing thousands of Tanzanian shillings in spoiled goods and keeps the food supply chain safe for communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Identify types of cold room
- Select tools and equipment
- Carry out diagnostic troubleshooting
- Select type of piping to be used
- Repair refrigerant pipes in both low and high side
Tathmini ya matokeo
A record of repairs carried out conforms to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to: Repair refrigerant pipes
Principles: Repair refrigerant pipes
Theories: The student should explain:
- Refrigerant pipe concept
- Types of refrigerant pipe in Cold rooms
Circumstantial knowledge:
Detailed knowledge about:
- Concept environmental regulation Safe handling working tool
Swali
What is the first step a technician should take when repairing a refrigerant pipe leak?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado