Mada za sehemu hiiRepairing central cooling systemsMada 4
- Repairing condenser
- Repairing compressor
- Repairing air handling unit
- Repairing duct work
Compressor Repair in Refrigeration and Air Conditioning Systems
A compressor is the heart of any refrigeration or air conditioning system. It circulates refrigerant by compressing low-pressure gas into high-pressure gas, enabling the cooling cycle to work. When a compressor fails, the entire system stops providing cooling, making repair skills essential for any refrigeration technician.
A compressor converts electrical energy into mechanical energy to pressurize refrigerant. In Tanzania, compressors are found in:
- Room air conditioners (split units, window units)
- Commercial refrigeration (cold rooms, supermarkets, butcher shops)
- Industrial cooling systems (food processing, pharmaceutical storage)
- Vehicle air conditioning (cars, buses, trucks)
Common types include reciprocating, rotary, scroll, and screw compressors. Each type has specific repair procedures, but general troubleshooting steps apply to all.
Before repairing, a technician must identify the problem correctly:
Common Compressor Faults
- Electrical failures — burnt motor windings, failed start capacitor, overload protector trip
- Mechanical failures — broken valves, worn bearings, seized piston
- Refrigerant-related failures — low charge, high charge, contaminated refrigerant
- Operational failures — short cycling, excessive noise, overheating
Diagnostic Steps
- Visual inspection — check for oil leaks, physical damage, rust
- Sound observation — listen for knocking, clicking, or humming sounds
- Temperature measurement — feel the discharge and suction lines
- Electrical testing — measure voltage, current, and winding resistance
- Pressure measurement — use gauges to compare operating pressures with normal values
Always observe safety measures before starting any repair:
- Disconnect power supply and lock out the electrical panel
- Wear safety goggles, gloves, and appropriate footwear
- Ensure adequate ventilation when handling refrigerants
- Use proper lifting techniques for heavy components
- Have a fire extinguisher nearby when working with electrical components
Step 1: Pump Down the System
A pump down isolates the refrigerant in the condenser, allowing safe work on the compressor.
- Connect manifold gauges to service valves
- Close the liquid line valve (metering device side)
- Start the compressor and run until low-side gauge reads near vacuum
- Close the suction service valve quickly
- Turn off the compressor
Step 2: Purge Noncondensates
Noncondensable gases (air, nitrogen) cause high head pressure and reduced efficiency.
- After pump down, slowly open the suction valve slightly
- Listen for hissing — this indicates air escaping
- Close the valve and check if pressure rises abnormally
- If pressure rises quickly, air is present and must be evacuated
Step 3: Remove and Inspect the Compressor
- Disconnect suction and discharge lines using appropriate wrenches
- Remove mounting bolts and lift the compressor carefully
- Inspect the shell for cracks or oil leaks
- Check the motor windings for continuity using a multimeter
Step 4: Repair or Replace
For minor repairs:
- Replace the start capacitor or overload protector
- Clean or replace the motor starting relay
- Repair electrical connections
For major failures:
- Replace the compressor assembly if motor windings are burnt or mechanical parts are damaged
- Ensure the replacement compressor matches the original specifications (voltage, refrigerant type, horsepower)
Step 5: Reinstall and Test
- Install the new or repaired compressor securely
- Connect lines and tighten with proper torque
- Evacuate the system using a vacuum pump to remove moisture
- Charge with the correct refrigerant amount
- Start the system and check:
- Normal operating pressures
- Proper superheat and subcooling
- No unusual noises or vibrations
- Cool air delivery at the evaporator
A supermarket in Dar es Salaam reports their cold room air conditioner is not cooling. The technician performs troubleshooting:
| Check | Finding | Diagnosis |
|---|---|---|
| Power supply | 230V available | Electrical supply OK |
| Compressor run current | 18A (rated 15A) | Overload condition |
| Discharge pressure | 280 psi (normal: 180-220 psi) | High head pressure |
| Suction pressure | 45 psi (normal: 30-40 psi) | Slightly high |
The compressor is drawing excess current due to mechanical wear. The technician performs a pump down, replaces the compressor with an identical model, evacuates to 500 microns, and recharges with R-404A refrigerant. After testing, pressures return to normal (200 psi discharge, 35 psi suction) and the cold room reaches the set temperature of -5°C.
- Manifold gauge set
- Vacuum pump
- Multimeter
- Leak detector
- Service valves and wrenches
- Torque wrench
- Refrigerant recovery machine
- Personal protective equipment
In Tanzania, refrigeration technicians with compressor repair skills can work in butcher shops in Kariakoo, cold storage facilities at the Dar es Salaam port, or service air conditioning units in hotels and offices. A technician who can competently repair a compressor saves a business owner from buying a new air conditioning unit costing TZS 1,500,000 or more, making this skill valuable for both employment and small business opportunities in local communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment for a task
- Perform diagnostic troubleshooting
- Repair/replace control equipment
- Perform pump down
- Purge the system of noncondensates
- Replace air filters
- Repair compressors
- Repair water pumps
- Repair or replace condenser
- Repair or replace evaporator
- Repair or replace duct and pipe installations
- Perform sheet metal works
- Carry out plumbing works
- Perform balancing of air delivery equipment
- Perform machine erection
- Store tools and equipment
- Clean equipment and workplace
- Perform riveting work
Tathmini ya matokeo
A record of maintenance and repair works carried out conforms to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Perform pump down
- To install new equipment
- Apply different leakage detection methods
- Perform diagnostic trouble shooting
- Charge refrigerant in a system using different methods
Principles: The student should explain the principles of:
- Heat transfer in a heat exchanger
- Compression refrigeration cycle
- Primary and secondary refrigerants
Theories: The student should explain:
- Pressure temperature charts for different refrigerants
- Super heating as it refers to refrigeration
Circumstantial knowledge:
Detailed knowledge about:
- Dismantling and assembling procedures
- Safe handling of working tools and equipment
- Electric circuitry
- Pressure and temperature quantities with reference to refrigeration
- Safe handling of refrigerants during charging, discharging and storage Environmental regulations on green gases
Swali
What is the primary function of a compressor in a refrigeration or air conditioning system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado