Mada za sehemu hiiPerforming threadMada 2
- Making external thread
- Making internal thread
An internal thread is a ridge or uniform section arranged in the form of a helix on the inside surface of a cylindrical hole. It is produced using a tool called a tap. Internal threads allow screws and bolts to be fastened into holes, which is essential when assembling or repairing refrigeration and air conditioning equipment.
Before learning to cut internal threads, you must understand these basic terms:
- Major Diameter – The largest diameter of the thread (outside diameter on a screw or nut)
- Minor Diameter – The smallest diameter of the thread (also called root diameter)
- Pitch – The distance from one point on a thread to the corresponding point on the next thread
- Pitch Diameter – The diameter of an imaginary cylinder that passes through the thread where groove and thread widths are equal
Tap
A tap is a hardened steel tool used for cutting internal threads in a drilled hole. It is held and turned using a tap wrench. Taps are made of high-carbon steel or high-speed steel (HSS) and come in a set of three:
- Taper Tap – Has 7 to 10 chamfered threads; used for starting the thread
- Plug Tap – Has 3 to 5 threads chamfered; used for general threading
- Bottoming Tap – Has one thread chamfered; used to finish the thread at the bottom of a blind hole
Tap Wrench
A tap wrench is a hand tool used to hold and turn taps. Two main types are:
- Double-end adjustable wrench
- T-handle wrench
Step 1: Determine the Correct Drill Size
Before drilling, you must know the size of the bolt you will use. For example, an M8 bolt requires an M8 tap, and the correct drill bit size is 6.8 mm.
Step 2: Drill the Hole
Drill a hole of the appropriate size for the bolt you are using. The hole must be clean and free from burrs.
Step 3: Select and Fix the Tap in the Wrench
Choose the correct tap (taper tap first, then plug tap, then bottoming tap if needed) and securely fix it in the tap wrench. Ensure the wrench is properly adjusted to fit the tap.
Step 4: Align the Tap Perpendicular to the Hole
Use a try square to ensure the tap is aligned at 90° to the workpiece. If the tap is not perpendicular, the threads will be crooked and unusable.
Step 5: Perform Hand Tapping
Apply cutting oil to the tap and hole. Turn the tap wrench clockwise to cut the thread. After every half turn, turn the tap slightly backward to break the chip. Repeat until the required depth is reached.
Step 6: Clean the Threads
After tapping, remove the tap carefully and clean out the metal chips (swarf) from both the tap and the workpiece.
Step 7: Check the Thread
Use a plug gauge to check if the thread is correct. The gauge should screw in smoothly without forcing.
Question: You need to tap a hole for an M8 bolt. What size tap should you use, and what is the appropriate drill bit size for prior drilling?
Answer:
- Tap size: Use an M8 tap (the tap must match the bolt size)
- Drill bit size: Use a 6.8 mm drill bit
This drill bit size is used because it creates a hole slightly smaller than the major diameter of the M8 thread, allowing the tap to cut the thread properly.
Tap Maintenance
- Clean the tap after each use to remove metal chips and cutting fluid
- Apply cutting fluid or lubricant while using the tap
- Store in a dry, cool place to prevent corrosion
- Inspect regularly for dull edges or chipped teeth
Tap Wrench Maintenance
- Clean after each use
- Ensure correct adjustment to fit the tap size
- Lubricate moving parts
- Store in a dry environment to prevent rust
- Replace or repair any damaged parts
- Always wear safety goggles, gloves, and safety boots
- Clamp the workpiece securely in a vice or on the drill table
- Keep fingers away from rotating tools
- Apply oil while cutting to reduce heat and friction
In Tanzania, a refrigerator repair technician often needs to make internal threads when fixing broken compressor bolts or mounting brackets. For example, if an M6 mounting bolt loses its thread in the refrigerator cabinet, the technician will drill a 5.0 mm hole and use an M6 tap to create a new internal thread, then secure the compressor with a new bolt — restoring the refrigerator to working order for a customer in Dar es Salaam.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Identify tools, equipment and material required
- Interpret the technical drawing
- Clamp the work piece on a bench vice
- Perform cutting of internal and external threads
- Clean the workplace and work piece
- Store tools, equipment and materials
Tathmini ya matokeo
Threads made conform to the given specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to make manual threads
Principles: The student should explain the principles of:
- Holding the work piece
- Thread cutting
- Sequencing the taps
- Making allowances for die cutting
Theories: The student should explain:
- The types of taps in a set
- Materials used for the manufacture of taps and dies
- The importance of applying oil when threading
- Standard threads
- Measurements
- How to calculate tap drill size (TDS)
- The uses of various tools and equipment
Detailed knowledge about:
- Safety precautions while thread cutting
- First aid requirements
- Environmental requirements
Swali
What is the name of the hardened steel tool used for cutting internal threads in a drilled hole?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado