Mada za sehemu hiiPerforming non fusion jointsMada 4
- Carrying out soldering
- Carrying out seaming
- Carrying out riveting
- Carrying out brazing
Seaming is a method of joining two pieces of metal by overlapping and folding their edges together without melting the base metal. It is a common non-fusion joint used in refrigeration and air conditioning work, especially when installing or repairing ductwork, pipe connections, and equipment housings.
Seaming creates a permanent joint by folding or crimping the edges of sheet metal together. Unlike welding, the base metal does not melt, so the original properties of the material remain unchanged. Seams are strong, leak-proof, and can be made quickly using basic hand tools.
Seaming is used for:
- Joining sections of ductwork in HVAC systems
- Closing edges of metal containers or panels
- Creating watertight seals in pipe installations
- Assembling equipment casings
There are several types of seams used in sheet metal work:
Pocket Seam — One edge of metal is folded over to hold the other edge inside a pocket. This creates a strong, concealed joint.
Lap Seam — Two pieces of metal overlap each other and are joined by folding the overlapping edges. Commonly used for ductwork.
Grooved Seam — A groove is formed along the edge of one piece, and the other piece fits into the groove before being folded.
Follow these steps to carry out a basic lap seam:
Step 1: Prepare the Materials
Select the metal sheets or pieces to be joined. Clean both surfaces using a wire brush to remove rust, dirt, or oxide layers. Ensure the edges are straight and free from burrs. Use marking out tools to mark the seam line clearly.
Step 2: Mark and Cut
Measure and mark the overlap distance on the edge of one piece. A typical overlap is 15 to 25 mm. Cut the edge to the required length using hand shears or snips. Use a pipe cutter if working with tubular sections.
Step 3: Form the Edge
Create a fold along the marked line using a mallet or appropriate forming tool. The fold should be approximately 90 degrees for a single hem. For a double hem, fold the edge back twice to create a reinforced edge.
Step 4: Join the Pieces
Place the prepared edge over the second piece of metal along the seam line. Ensure proper alignment and tight contact between the overlapping surfaces.
Step 5: Close the Seam
Use a seaming tool or mallet to fold the overlapping edge over firmly. Work along the entire length of the seam to ensure a uniform fold. For a grooved seam, use a grooving tool to create the groove before folding.
Step 6: Inspect the Joint
Check the seam for any gaps, uneven folds, or damage. The joint should be tight and secure. If necessary, adjust and refold any problem areas.
When performing seaming, always observe safety measures:
- Wear safety boots and a welding apron when handling metal edges
- Use gloves to protect hands from sharp edges
- Keep tools in good condition and use the correct tool for each task
- Work in a clean, organized area free from clutter
- Inspect all tools before use
A student at VETA is making a small duct section for a practice air conditioning unit. The student has two pieces of galvanized sheet metal, 300 mm by 200 mm each. Following the seaming process, the student marks a 20 mm overlap on one piece, cuts the edge cleanly, forms a single hem, overlaps the pieces, and closes the seam using a mallet. The resulting joint is strong enough to hold air pressure when tested and does not leak. This skill will be used when installing actual ductwork in buildings.
In Tanzania, seaming is a practical skill used by refrigeration and air conditioning technicians when installing or repairing split air conditioners in homes, shops, and offices. For example, when connecting the copper pipe from the indoor unit to the outdoor unit, a technician may use seaming techniques to join ductwork for the air distribution system. Small business owners in Dar es Salaam and other regions who offer HVAC repair services use these seaming skills to make cost-effective, leak-free joints without expensive welding equipment, earning income from air conditioner installation and maintenance in their communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Choose appropriate jointing system
- Take measurements
- Perform pipe cutting
- Perform filing
- Perform swaging
- Perform pipe bending
- Perform even and correct heating
- Perform initial seaming
- Store tools and equipment
- Clean workplace and joints
Tathmini ya matokeo
A number of work pieces joined conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Take linear measurements
- Join similar and dissimilar metals
- Choose appropriate method for different material
Principles: The student should explain the principles of: capillary action
Theories: The student should explain:
- Alloyed copper brazing properties
- Effects of excess flux on joints
- Material composition suitable for brazing or soldering
Detailed knowledge about:
- Safe handling of tools and equipment
- Restrictions on spot brazing
- Prevention of scale formation inside pipe joints
- Preparation of surfaces for brazing or soldering
- When to apply hard or soft solder
Swali
What is seaming in refrigeration and air conditioning work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado