Mada za sehemu hiiPerforming cold electrical jointsMada 4
- Making eyelet joint
- Making crimp joint
- Making parallel groove clamp joint
- Making bolt joints
A bolt joint is a type of electrical connection where two or more wire ends are placed together and secured tightly using a bolt, nut, and washer. This creates a permanent, strong electrical connection that conducts current reliably.
- Diagonal cutting pliers
- Combination pliers
- Electrician knife
- Set of spanners
- Measuring tape
- Long nose pliers
- Analog or digital multimeter
- Bolts, nuts, and washers of appropriate size
- Copper wire or conductors to be joined
- Electrical insulation tape (for finishing)
- Always wear safety goggles to protect your eyes from flying wire pieces
- Wear safety boots to protect your feet from heavy tools
- Put on overalls to protect your clothing
- Ensure the work bench is stable and clear of clutter
- Never work on live circuits — always disconnect power first
- Use insulated tools when possible
1. Prepare the Wires
- Measure and cut the required length of wire using diagonal cutting pliers
- Strip the insulation from the wire ends using an electrician knife, exposing about 2-3 centimeters of bare copper
- Use long nose pliers to form a small loop or hook at the end of each wire, making it easy to pass around the bolt
2. Select the Correct Bolt and Hardware
- Choose a bolt of appropriate length and gauge for the wire size
- Ensure the bolt, nut, and washer are made of conductive material (usually copper or brass for electrical work)
- The bolt diameter should be large enough to accommodate all wire ends without forcing them
3. Assemble the Joint
- Place a washer onto the bolt first
- Pass the first wire loop around the bolt
- Add another washer for better contact
- Pass the second wire loop around the bolt
- Add a final washer and tighten the nut securely using spanners
4. Test the Connection
- Use a multimeter to check for continuity across the joint
- Set the multimeter to continuity mode (or resistance, Ω)
- Place one probe on the bolt and the other on the end of the second wire
- A reading of zero or near-zero ohms indicates a good connection
5. Insulate the Joint
- Wrap electrical insulation tape around the entire joint for safety
- Ensure no bare copper is exposed to prevent short circuits or shocks
A refrigerator technician needs to join two 2.5mm² copper wires inside a cold room unit. The wires have been cut during maintenance and need to be reconnected.
Procedure:
- Strip 2.5 cm of insulation from each wire end using the electrician knife
- Form a hook at each stripped end using long nose pliers
- Select a 6mm diameter brass bolt, two washers, and a nut
- Place washer → first wire loop → washer → second wire loop → washer on the bolt
- Tighten the nut firmly with a spanner
- Test with a multimeter — continuity is confirmed
- Wrap with insulation tape
The joint is now complete and ready for use in the refrigeration system.
In Tanzania, refrigeration and air conditioning technicians use bolt joints when repairing refrigerators in markets like Mwanza or Arusha, or when installing split air conditioners in homes and shops. For example, when a restaurant owner's deep freezer stops working in Dar es Salaam, a technician would use bolt joints to reconnect damaged power cables, restoring the equipment to working condition and helping preserve food worth TSH 500,000 or more.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment and materials required
- Prepare cables for joint making
- Make bolt joints
- Insulate joints
- Terminate
- Clean workplace and tools Store tools, equipment and excess/remaining materials
Tathmini ya matokeo
The joint made is mechanically and electrically correct conforming to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Strip a cable
- Make bolt joints
- Insulate joints
Principles: The student should explain principle of:
- Making bolt joints
- Stripping a cable
- Termination
Theories: The student should explain:
- Different types of joints
- Different materials used in joint making
- Tools for stripping and cutting a cable
- Different types of insulating materials
Detailed knowledge about:
- Performing termination
- Handling soldering materials
Swali
What is the primary purpose of a bolt joint in electrical work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado