Mada za sehemu hiiConstructing RLC circuitsMada 3
- Building a resistance and capacitance circuit
- Building a resistance and inductance circuit
- Building a resistance inductance and capacitance circuits
Resistance and Inductance Circuit
A resistance and inductance circuit (RL circuit) is an electrical circuit that contains a resistor (R) and an inductor (L) connected together. This type of circuit is important in refrigeration and air conditioning because components like compressor motors and fan motors contain inductors (coils of wire) that work together with resistors to control current flow and create magnetic fields.
- Battery (DC source): Provides the electrical energy/pressure that pushes current through the circuit
- Resistor (R): Limits the amount of current flowing in the circuit and converts electrical energy to heat
- Inductor (L): A coil of wire that stores energy in a magnetic field when current flows through it
- Switch: Opens or closes the circuit to control when current flows
- Connecting wires: Carry current from one component to another
- Multimeter: Measures voltage, current, and resistance
Before building any circuit, always:
- Wear safety goggles to protect your eyes
- Wear overalls and safety boots
- Make sure your hands are dry
- Never touch bare wires while the circuit is connected to power
- Disconnect the battery before making any changes to the circuit
Step 1: Plan Your Layout
Place all components on the work bench in a logical arrangement. Keep the circuit neat and easy to follow. The resistor and inductor should be positioned where they can be easily connected.
Step 2: Prepare the Wires
Use combination pliers to cut wires to appropriate lengths. Use long nose pliers to strip about 1 cm of insulation from each wire end. This exposes the copper conductor for good electrical connection.
Step 3: Connect the Resistor
Insert the resistor leads into the proto board or secure them with terminal clips. Remember that resistors are not polarity-sensitive — they can be connected in either direction.
Step 4: Connect the Inductor
Place the inductor (coil) in the circuit. The inductor also has no polarity, so direction does not matter. However, handle it carefully to avoid bending or damaging the coil windings.
Step 5: Connect the Switch
Insert the switch into the circuit. The switch controls whether the circuit is complete (ON) or broken (OFF).
Step 6: Connect the Battery
Connect the positive terminal of the battery to one end of the switch. Connect the negative terminal to the rest of the circuit. Always connect the battery last.
Step 7: Connect the Multrometer
Set your multimeter to measure DC current (A) or voltage (V) as needed. Connect it in series to measure current or in parallel to measure voltage.
When you close the switch:
- Current begins to flow from the battery through the resistor
- The resistor limits the current to a safe value
- As current passes through the inductor, a magnetic field builds up around the coil
- The inductor opposes changes in current (this property is called inductance)
- If you open the switch, the magnetic field collapses and tries to keep current flowing briefly
Problem: A simple RL circuit has a 12 V battery, a 100 Ω resistor, and an inductor connected in series. If the switch is closed, calculate the current flowing through the circuit assuming the inductor has very low DC resistance.
Solution:
Using Ohm's Law: I=RV
I=100 Ω12 V=0.12 A
The current flowing through the circuit is 0.12 amperes (or 120 milliamps).
In a real RL circuit, the inductor would cause the current to rise gradually rather than instantly, but after a short time the current reaches this steady value.
- Voltage across components: Connect multimeter in parallel across each component
- Current in the circuit: Connect multimeter in series (break the circuit and insert the meter)
- Resistance: Disconnect the battery first, then measure resistance across each component
- No current flowing: Check all connections are secure; ensure switch is closed; verify battery is charged
- Unusually high current: Check resistor value is correct; look for short circuits
- Inductor overheating: Reduce current; check for correct resistor value
In Tanzania, RL circuits are found in the starting winding of single-phase air conditioner compressors. The inductor (coil) creates a magnetic field to start the motor, while the resistor limits the current to protect the windings. When an AC unit in Dar es Salaam fails to start, technicians often check the resistance of the compressor windings using a multimeter — a skill you practice when building resistance and inductance circuits in the workshop.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret given diagram of the RLC circuit
- Select equipment, tools and material required
- Prepare inductors, capacitors, resistors and wire for termination
- Build resistance and inductance circuit Solder the built circuits
- Test the built circuits
- Clean the work area, tools and equipment
- Store tools, equipment and the excess materials
Tathmini ya matokeo
The RLC circuit constructed conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to construct RLC circuits
Principles: The student should explain the principles of:
- Constructing RLC circuit
- Carrying out measurement of voltage in an RLCL circuit
Theories: The student should explain:
- The RLC circuit and its behaviour
- The application of the various types of Inductive circuits
Detailed knowledge about:
- Safety precaution when soldering RLC circuits
- Safe handling of working tools, equipment and RLC components
Swali
Which of the following components is NOT needed to build a basic resistance and inductance (RL) circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado