Mada za sehemu hiiEnlarging and reducing of figuresMada 1
- Performing enlarging and reducing of plane figures
What Are Enlargement and Reduction?
Enlargement is the process of making a figure bigger while keeping its shape the same. Reduction is the process of making a figure smaller while keeping its shape the same. Both processes create similar figures — figures that have the same shape but different sizes.
In both enlargement and reduction:
- All corresponding angles remain equal
- All corresponding sides change in the same proportion (ratio)
- The perimeter changes in the same ratio as the sides
Key Concept: Ratio and Proportion
When enlarging or reducing, we use a scale ratio. For example:
- A ratio of 1:3 means the new figure is 3 times larger than the original
- A ratio of 3:5 means the new figure is smaller (reducing) — the original is divided into 5 parts and we take 3 of those parts
The radial method uses a pole (a point) from which lines are drawn through each corner of the original figure. This method works with either an external pole (outside the figure) or a central pole (inside or at the centre).
Steps for Enlargement Using Radial Method (External Pole)
To enlarge a figure by a given ratio (for example, 1:3):
- Choose a pole (P) at a convenient point outside the figure
- Draw radials from P through each corner (vertex) of the original figure
- Set up the ratio: On one radial line, measure the distance from P to a corner, then divide this distance into the number of parts shown in the ratio (for 1:3, divide into 3 equal parts)
- Mark the new corner: The point at the required number of parts (point 3 for 1:3) becomes the new corner
- Draw parallels: From the new corner, draw lines parallel to the original sides to complete the enlarged figure
- Complete the figure by repeating parallels for all sides
Steps for Reduction Using Radial Method (Central Pole)
To reduce a figure by a given ratio (for example, 5:3):
- Draw the original figure (for example, a pentagon)
- Choose a pole (P) near the centre of the figure
- Draw radials from P to each corner of the figure
- Set up the ratio: On one radial line, mark the distance from the corner to P, then divide this distance into the number of parts in the first ratio (5 parts for 5:3)
- Mark the reduced point: Count the number of parts from the second ratio (3 parts) — this gives the position of the reduced corner
- Draw parallels: From each new corner, draw lines parallel to the original sides, intersecting the radials
- Complete the reduced figure
The direct method uses a starting point located at one edge (corner) of the original figure. Lines are radiated from this corner to enlarge or reduce the figure.
Steps for Reduction Using Direct Method
To reduce a figure by a given ratio (for example, 3:2):
- Identify a corner of the original figure to serve as the starting point
- Draw a radial from this corner to an opposite side
- Set up the ratio: On a side adjacent to the starting corner, divide the side length into the number of parts in the first ratio (3 parts for 3:2)
- Mark the reduced point: Count the required number of parts (2 parts) from the starting corner
- Draw parallel lines: From this reduced point, draw lines parallel to the original sides to intersect the radial
- Complete the reduced figure
Question: Enlarge triangle ABC using radials from an external pole by the ratio 1:2
Solution:
- Draw triangle ABC and choose pole P outside the triangle
- Draw radials from P passing through A, B, and C
- On the radial from P through A, measure PA and divide it into 2 equal parts
- From P, mark point A' at distance 2 parts from P (this is the enlarged point)
- Through A', draw a line parallel to AB to intersect the radial through B at B'
- Through B', draw a line parallel to BC to intersect the radial through C at C'
- Triangle A'B'C' is the enlarged figure (twice the size of the original)
- When working with figures containing arcs and radii, the radials must pass through the centres of arcs and points of tangency
- Always keep angles exactly the same — only the side lengths change
- Use precise drawing instruments: ruler, compass, set squares, and protractor
- Always start with a clean, accurate construction of the original figure
- Keep your construction lines light — they should be visible but not confused with the final figure
- Check that corresponding angles are equal using a protractor
- Verify that all sides are in proportion by measuring
In Tanzania, technicians and craftsmen use enlargement and reduction when copying or scaling technical drawings. For example, a carpenter drawing a furniture design from a small sketch in a notebook onto a full-size workshop drawing (enlargement), or a technician reducing a large machine layout to fit onto a standard A4 report document (reduction), applies these same methods to ensure the proportions remain accurate while changing the size.
Jinsi utakavyotathminiwaTathmini ya mchakato
Tathmini ya mchakato
Methods for enlarging and reducing figures are identified and applied as per given instructions.
Swali
What is the primary change that occurs when a plane figure is enlarged or reduced?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado