Mada za sehemu hiiHandling accidents and incidentsMada 5
- Handling mechanical hazards
- Handling physical hazards
- Handling chemical hazards
- Handling electrical hazards
- Maintaining safety gear
Electrical hazards are dangerous situations caused by electricity that can lead to fires, burns, electric shocks, or even death. In a handloom workshop, where power machines are used, understanding and handling these hazards is essential to keep yourself and others safe.
Electrical hazards are conditions or events involving electricity that can cause harm to people or damage to property. In a weaving workshop, these hazards can arise from damaged equipment, improper use of electrical tools, or poor maintenance of wiring and machines.
- Damaged or frayed electrical cords — worn-out wires can expose live electrical parts
- Overloaded power sockets — plugging too many machines into one socket can cause overheating
- Wet hands or wet floors — water conducts electricity and increases the risk of shock
- Faulty switches and plugs — damaged switches can spark and cause fires
- Using machines without proper earthing — this increases the risk of electric shock
- Blocked or disorganised work areas — cords and cables left on the floor can be tripped over or damaged
- Electric shock — current passing through the body makes the muscles tighten, so the person may be unable to let go. It can stop the breathing muscles (the respiratory system) and disturb the heartbeat, so that the heart no longer pumps blood (the circulatory system) and the brain is starved of oxygen
- Burns — where the current enters and leaves the body, often deeper than they look
- Falls and other injuries — a shock can throw a person off balance or against a machine
- Fire — overheated cables, sparks and overloaded sockets can set cotton fluff, yarn and cloth alight
- Damage to machines and loss of work
Step 1: Identify the Hazard
Before using any electrical equipment, always check for visible signs of damage such as:
- Frayed or cut wires
- Loose plugs or switches
- Burn marks on machines or sockets
- Unusual sounds or smells from machines
Step 2: Take Preventive Measures
- Always switch off machines before plugging or unplugging them
- Keep electrical cords away from water and wet areas
- Do not overload sockets — use one machine per socket when possible
- Make sure your hands are dry and wear dry, rubber-soled safety boots when operating electrical equipment
- Ensure machines are properly earthed (connected to the earth wire)
- Keep the workshop floor clean and dry
- Cover loose cables and cords to prevent tripping and damage
- Hand damaged cords, plugs, bulbs and used batteries to your teacher for safe disposal; never throw them in a fire or leave them where they could be used again
Step 3: Know Emergency Response
If an electrical accident occurs:
- Do not touch the injured person if they are still in contact with electricity
- Switch off the power source immediately using the main switch or circuit breaker, or by pulling out the plug
- Call for help and alert others in the workshop
- Only if the power cannot be switched off, stand on something dry that does not conduct electricity (a dry wooden board, a rubber mat or a thick book) and push the person clear with a dry wooden broom handle. Never use anything metal or wet. If the accident involves a fallen power line or other high-voltage equipment, stay well away and call the electricity company and the emergency services
- Give first aid once the person is free of the current, as described in the next section
- If something is on fire, switch off the power and use a carbon dioxide (CO2) or dry powder extinguisher. Never use water or foam on electrical equipment
- Report the incident to the workshop supervisor and record it in the accident book: the date, time and place, who was hurt, which machine was involved, what happened and the first aid given
Touch the person only when you are sure the power is off or they are clear of it. Then:
- Check for a response by gently shaking the shoulders and speaking loudly
- Send for help from the emergency services or the nearest health facility
- Open the airway by tilting the head back gently and lifting the chin, and check for normal breathing for no more than 10 seconds
- If the person is breathing normally, place them on their side in the recovery position and keep checking their breathing
- If the person is not breathing normally, start at once: 30 chest compressions (hands on the centre of the chest, pushing down 5 to 6 cm, about two pushes every second), then 2 rescue breaths, and repeat without stopping until help takes over or the person breathes. If you cannot give breaths, give compressions only
- Cool any burns under cool running water for at least 20 minutes and cover them loosely with a clean, non-fluffy cloth
Anyone who has had an electric shock must be checked at a health facility, even if they feel well, because the heart can be affected later.
- A yellow triangle with a black lightning flash warns of dangerous electricity
- A red circle with a diagonal line forbids an action, for example a DO NOT SWITCH ON tag on a machine under repair
- A blue circle shows something you must do, such as switching off before cleaning
- Green signs show the first aid kit and the emergency exit; red signs show fire equipment
- Red buttons stop a machine and green buttons start it
- In the flexible cord of a machine, the brown wire is live, the blue wire is neutral and the green-and-yellow wire is earth. Knowing this helps you to understand a warning, but only a qualified electrician may open plugs, sockets or machines
When working with electrical machines in the workshop, always wear:
- Gloves for handling rough materials, kept dry (ordinary gloves do not protect you from electric shock)
- Safety boots with dry rubber soles (they reduce the current that could pass through your body to the ground)
- Overalls or apron (to protect your body)
- Mask (when required, especially in dusty conditions)
Keep a first aid kit nearby at all times. Safety gear lowers the risk, but it never makes it safe to touch bare wires or to open electrical equipment.
Mariam, a Form 1 student, noticed that the cord of the electric motor used for her loom was frayed near the plug. She should:
- Stop using the machine immediately and switch it off at the wall socket, without touching the damaged part of the cord
- Report the problem to the teacher or workshop supervisor
- Do not attempt to repair it herself
- Wait until a qualified electrician replaces or repairs the cord
- Continue working only after the cord has been safely repaired
This prevents electric shock and potential fire hazards.
- Always inspect electrical equipment before use
- Keep water away from electrical sources
- Wear the correct safety gear
- Know where the main power switch is located
- Never try to fix electrical faults yourself — report them
- In an emergency, cut off the power first, then help
In a Tanzanian market workshop where tailors and weavers use sewing machines and electric winding machines, a fault in the wiring could cause a fire that destroys expensive equipment. By following proper electrical safety procedures, a craftsperson can protect their livelihood, avoid medical expenses from electrical burns, and ensure their small business continues operating safely for years to come.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should explain how to:
- Select tools and equipment
- Observe safety precautions
- Identify electrical hazard
- Handle electrical hazards
- Report to superiors
- Record accidents
Tathmini ya matokeo
Electrical hazards are properly handled
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to handle electrical hazards points
Principles: The student should explain the principles of handling electrical hazards
Theories: The student should explain:
- Effect of electrical hazards
- Treatment for an unconscious person
- Usage of colour codes and safety signs
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions while handling accidents
- Safe handling of tools, equipment, and machines
- Waste disposal methods
- Respiratory and circulatory systems
Swali
What does a yellow triangle with a black lightning flash safety sign mean?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado