Mada za sehemu hiiMaking knitted fabric using single flat machineMada 2
- Setting up and preparing the weft knitting machine
- Knitting the fabric
Weft knitting is a method of fabric construction where a single yarn is looped horizontally across the fabric, with each row building on the previous one. Setting up the weft knitting machine correctly is essential because it ensures smooth fabric production, prevents fabric defects, and protects the operator from injury. This study note guides you through the process of preparing the flat weft knitting machine for production.
Before touching the machine, always put on your safety gear:
- Safety glasses – protect your eyes from flying yarn fibers or broken needles
- Apron or lab coat – keep clothing away from moving machine parts
- Closed shoes – prevent injuries from dropped tools or needles
- Tie back long hair – avoid getting hair caught in the machine
Never operate the machine with loose jewelry or watches.
Understanding the machine parts helps you set it up properly:
- Needles – the metal hooks that form the loops
- Sinkers – metal plates that hold the old loops while new ones are formed
- Presser bar – holds needles in place during knitting
- Yarn feeder – guides the yarn to the needles
- Fabric take-down roller – pulls the fabric downward as it is formed
- Tension device – controls yarn tension for even stitches
Step 1: Inspect the Machine
Check that the machine is clean and free from lint, broken needles, or damaged parts. Look at the needle bed and sinkers — if any needles are bent or broken, replace them before starting. Make sure the machine is securely bolted to the table or stand.
Step 2: Select and Prepare the Yarn
Choose a suitable yarn for your project. The yarn should be:
- Free from knots or thick spots
- Soft and flexible, not overly stiff
- Wound neatly on a cone or spool
Before threading, pull out about 1 meter of yarn from the cone and check for breaks or irregularities. If the yarn is too tangled, wind it onto a smaller bobbin before use.
Step 3: Thread the Yarn Through the Tension Device
Pass the yarn through the tension disc or weight system. This device controls how tightly the yarn is pulled during knitting. Adjust the tension so the yarn feeds smoothly — too loose causes dropped stitches, and too tight causes the yarn to break.
Step 4: Attach the Yarn to the Yarn Feeder
Thread the yarn through the yarn feeder, making sure it sits in the groove correctly. The yarn feeder should be positioned at the center of the needle bed for starting. Some machines have a latch or clip to hold the yarn end in place.
Step 5: Set the Fabric Take-Down Mechanism
The fabric take-down roller pulls the newly formed fabric away from the needles. Adjust the tension so the fabric comes off the machine at an even pace — too fast causes uneven stitches, and too slow causes the fabric to bunch or curl.
Step 6: Prepare the Needle Bed
Move the carriage to one end of the machine. Make sure the presser bar is in the raised position. This allows the needles to receive the yarn correctly on the first pass.
Step 7: Cast On the First Row
For the first row, you may use a temporary cast-on method or the machine's built-in starting procedure. Hold the yarn end with one hand while slowly turning the hand wheel or pushing the carriage across. Watch to ensure every needle catches the yarn.
Step 8: Test the Machine
Knit 3–5 rows by turning the hand wheel slowly. Check the fabric for:
- Even stitch size
- No dropped stitches
- No broken needles
- Smooth yarn feeding
If problems appear, stop and recheck yarn tension, needle condition, and yarn feeder position.
A Form 3 student at Mwenge Secondary School is preparing to knit a simple scarf using a flat weft knitting machine. The yarn is soft cotton, and the machine has been sitting unused for one week.
The student should follow these steps:
- Put on safety glasses and apron.
- Clean the needle bed with a soft brush, removing dust and old lint.
- Check all needles — replace 2 bent needles found at the center of the bed.
- Take the yarn cone, pull out 1 meter, and check for breaks. The yarn is clean.
- Thread the yarn through the tension device and set the tension to a medium level.
- Attach the yarn to the yarn feeder at the center position.
- Adjust the fabric take-down roller to a medium tension setting.
- Cast on the first row by hand, then knit 5 test rows.
- The fabric looks even with no dropped stitches — the machine is ready for production.
| Problem | Possible Cause | Solution |
|---|---|---|
| Dropped stitches | Yarn tension too loose | Increase tension or check yarn feeder position |
| Broken yarn | Yarn tension too tight or yarn has weak spots | Reduce tension; replace damaged yarn section |
| Uneven fabric | Take-down tension uneven | Adjust fabric take-down roller |
| Fabric curling | Needle timing off or presser bar not aligned | Stop machine and check needle alignment |
Before you begin any knitting project, confirm:
- Safety gear is worn
- Machine is clean and inspected
- Needles are straight and undamaged
- Yarn is prepared and free from defects
- Yarn is threaded through tension device
- Yarn feeder is correctly positioned
- Fabric take-down is set to correct tension
- First few test rows are even and error-free
In Tanzania, handloom weaving skills are used by small-scale textile entrepreneurs in markets like Mwenge and Kariakoo, where artisans produce scarves, table runners, and bedspreads for sale. A young entrepreneur in Arusha who masters setting up a flat weft knitting machine can start a small business making custom knitted items to sell to tourists or at local exhibitions, using locally available cotton yarn to keep costs low while earning an income.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Student should explain how to:
- Select tools and equipment
- Observe safety precautions
- Thread the yarn through the feeders
- Set machine parameters like stitch density and tension
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Basic weft knitted structures are correctly drawn
Tathmini ya maarifa
Knowledge evidence: Detailed knowledge of:
Method used: The student should explain how to: Set up and prepare the weft knitting machine
Principles: The student should explain the principles of: Setting up and prepare the weft knitting machine
Theories: The student should be able to explain:
- How to set up and prepare the weft knitting machine
Circumstantial knowledge:
Detailed knowledge of: Essential components required to form knitted fabric
Swali
Before touching the weft knitting machine, which safety measure is NOT mentioned in the lesson?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado