Mada za sehemu hiiConstructing surface drainageMada 4
- Planning for surface water removal
- Constructing open and closed channels for rainwater
- Harvesting rainwater
- Constructing underground water tank
Underground water tanks are structures built below the ground surface to collect and store water for various uses such as domestic supply, irrigation, and fire protection. These tanks utilise gravity to distribute water and help manage water resources efficiently, especially in areas where surface water is scarce or unreliable.
Underground water tanks serve several important functions in construction and water management:
- Water storage: They store harvested rainwater or water from other sources for later use
- Space saving: Since the tank is underground, it does not occupy valuable surface space
- Temperature regulation: Underground temperatures remain relatively constant, keeping water cool
- Pressure management: Water stored underground can be distributed using gravity without pumps
Before construction begins, proper site selection is essential:
- Ground conditions: Choose a location with stable, non-expansive soil that can support the tank structure
- Water table: The tank bottom should be at least 1 metre above the highest water table level to prevent groundwater ingress
- Accessibility: The site should allow easy access for construction equipment and future maintenance
- Proximity: Position the tank close to the building it will serve to minimise piping costs
The excavation creates the space where the tank will be built:
- Marking out: Use pegs and strings to mark the exact dimensions of the tank on the ground
- Excavation: Use shovels, spades, or excavators to dig to the required depth, typically 1.5 to 3 metres depending on water demand
- Bottom levelling: Ensure the excavation bottom is level and compacted
- Side wall stability: Slope the excavation walls slightly outward to prevent collapse, or install temporary shoring
A solid foundation prevents cracking and failure:
- Compacted soil base: Compact the excavation bottom thoroughly using compaction tools
- Blinding concrete: Pour a 50-100mm layer of lean concrete (1:4:8 mix) over the base to create a level working surface
- Drainage layer: Place a layer of clean gravel or crushed stone at the base to allow any water infiltration to drain away
Steel reinforcement strengthens the concrete structure:
- Rebar placement: Cut and bend reinforcement bars according to the design specifications
- Wall reinforcement: Install vertical and horizontal rebar in the tank walls, typically with 12-16mm diameter bars
- Floor reinforcement: Place a mesh of rebar on the tank floor, raised slightly on concrete spacers
- Cover: Maintain minimum 25mm concrete cover around all reinforcement to prevent corrosion
Formwork shapes the concrete and must be properly installed:
- Wall formwork: Erect formwork panels (plywood or metal) on both inside and outside of the walls
- Bracing: Secure formwork with braces and tie wires to withstand concrete pressure
- Waterstop joints: Install waterstops at the wall-floor junction to prevent water leakage
- Access openings: Position formwork for inlet, outlet, and inspection pipes
Concrete forms the watertight shell of the tank:
- Mix proportion: Use a strong concrete mix, typically 1:2:4 (cement:sand:aggregate) with maximum 50mm slump
- Placement: Pour concrete in layers, each layer compacted with vibrators or manual tamping
- Curing: Keep concrete moist for at least 7 days by covering with wet burlap or sprinkling water regularly
- Wall thickness: Underground tank walls are typically 150-200mm thick for residential use
Waterproofing prevents water ingress and contamination:
- Surface preparation: Clean concrete surfaces and repair any cracks or voids
- Membranes: Apply waterproofing membranes or coatings to both interior and exterior surfaces
- Joint treatment: Seal all construction joints and penetrations with appropriate sealants
- Testing: Fill the tank with water and monitor for 24-48 hours to check for leaks before backfilling
Backfilling stabilises the tank after construction:
- Material: Use well-graded, compactable soil free from large stones or organic matter
- Layers: Place backfill in layers of 200-300mm, compacting each layer thoroughly
- Compaction: Use compaction tools to achieve at least 95% Proctor density
- Surface grading: Grade the surface to direct surface water away from the tank
Construction work requires proper safety measures:
- Personal protective equipment (PPE): Always wear hard hats, safety boots, gloves, safety goggles, and high-visibility vests
- Excavation safety: Never enter unsupported excavations; use trench boxes or shoring for deep excavations
- Electrical safety: Keep electrical equipment away from wet conditions; use ground fault circuit interrupters
- Dust protection: Wear dust masks when working with cement or in dusty conditions
- Fall protection: Use harnesses when working at heights
A household in Dodoma wants to build a rectangular underground water tank to store rainwater from their roof.
Given:
- Length = 3 metres
- Width = 2 metres
- Depth = 2 metres
Calculate the storage capacity in litres:
Solution:
Volume = Length × Width × Depth Volume=3m×2m×2m=12 cubic metres
Since 1 cubic metre = 1000 litres: 12×1000=12,000 litres
This tank can store 12,000 litres of water, which is sufficient for a typical household of 5-6 people for several days.
In Tanzania, many rural and peri-urban households construct underground water tanks to store rainwater during the rainy season for use in the dry season. A small-scale farmer in Morogoro might build a 10,000-litre underground tank (approximately TZS 1,500,000 to 2,500,000 in construction cost) to store rainwater for irrigating vegetables during the dry months, reducing reliance on expensive borehole water or tanker deliveries that can cost TZS 20,000-30,000 per 5,000 litres.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret design specifications and site plans for the tank.
- Assess soil conditions and site suitability.
- Prepare tools and materials for construction.
- Excavate the site to the required dimensions
- Construct the tank walls
- Ensure proper waterproofing techniques are applied
- Implement access points and drainage features
- Clean tools and store
- Clean working area
Tathmini ya matokeo
Underground water tank constructed in conformance with design specifications, safety standards, and construction regulations.
Tathmini ya maarifa
Detailed knowledge of:
Method used: The students should explain procedures for constructing an underground water tank.
Principles: The student should explain the principles involved in constructing underground water tank.
Theories: The students should explain:
- Role of underground tanks in water storage and conservation.
- Impact of design on water quality and accessibility. Circumstantial Knowledge: Knowledge about:
- Materials and tools for tank construction.
- Safety measures during the construction process.
Swali
What is one main advantage of placing an underground water tank below ground level?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado