Mada za sehemu hiiSetting out a buildingMada 4
Profile boards, also called batter boards or profile frames, are temporary wooden structures used in construction to precisely mark the outline and corners of a building's foundation. They consist of horizontal boards supported by vertical stakes (pegs) driven into the ground outside the excavation area. String lines (ranging lines) are tied between the boards to define the building's dimensions, ensuring accurate placement of foundation walls.
A typical profile board is made from a horizontal board measuring approximately 75mm × 30mm × 850mm. This board is face-fixed through two supporting pegs driven firmly into the ground. Nails or shallow saw cuts on the horizontal board mark the precise locations where string lines will be attached.
Profile boards serve several essential purposes in building construction:
- They provide permanent reference points for the building's outline after corner pegs are removed
- They allow string lines to be detached and reattached while maintaining accurate positioning
- They hold information such as foundation width and excavation lines
- They remain in place for extended periods, enabling daily checks for accuracy
The process of positioning profile boards follows a systematic sequence:
Step 1: Using one of the right angle methods (3:4:5 method, builder's square, or optical square), set up pegs at all four corners to create a rectangle representing the building outline.
Step 2: Check that the diagonal measurements are equal. If both diagonals measure the same length, the corners are at 90° and the rectangle is square.
Step 3: Extend the lines of each side beyond the corner positions to determine where profile boards should be placed. Profile boards are typically positioned about 500mm from the corner pegs to allow working space for excavation.
Step 4: Drive the supporting pegs for each profile board and attach the horizontal board at a convenient height (usually around waist level for easy access).
Step 5: Transfer the wall position from the corner peg to the profile board. This is done by keeping the ranging line tight and in contact with the nail at the top of the corner peg, then extending it back to the profile board. Mark the position on the top edge of the profile board with a pencil.
Step 6: Insert a clout nail at the marked position or make a shallow saw cut to secure the ranging line.
Step 7: Remove the corner pegs and attach the ranging lines to the profile boards. At this stage, recheck the setting-out for both square and accuracy of dimensions.
Profile boards must be horizontal, and all profile boards around the building must be level with one another. For accuracy when extending and re-establishing ranging lines, the profile boards should be set at the same level as the original corner pegs.
The distance between the original corner pegs and the profile board is only about 500mm, so the level is easily transferred using a spirit level. Place the spirit level on the horizontal board and adjust until it is level, then secure the board in position.
It is good practice to check the accuracy of the setting-out at the start of every working day, as pegs and profiles could have been disturbed.
A builder needs to set out profile boards for a rectangular house foundation measuring 8m × 6m.
Step 1: Establish the front baseline using a reference point (such as a boundary line). Drive two corner pegs 8m apart.
Step 2: Use the 3:4:5 method to set out a right angle at the first corner. From the first peg, measure 3m along the baseline and mark point A. From the same peg, extend a second line and measure 4m to point B. Adjust until the distance between A and B is exactly 5m.
Step 3: Complete the rectangle by measuring 6m from the right angle corner to establish the fourth corner.
Step 4: Check diagonals: both should measure √(8² + 6²) = √100 = 10m. Equal diagonals confirm the rectangle is square.
Step 5: Position profile boards 500mm outside each corner. Transfer wall positions to each profile board using the method described above, securing ranging lines with nails.
Profile boards can contain additional information useful during construction:
- Foundation width: Extra ranging lines can be attached to mark the foundation width, allowing excavation lines to be marked on the ground using lime or spray paint
- Centre line: Some excavator drivers prefer the centre line of the foundation trench to be marked, as it helps them centre the excavator's bucket accurately
After excavation and concrete placement, the ranging lines can be re-created at the external wall-line positions, checked for accuracy, and then transferred down to the foundation level for brickwork setting out.
In Tanzania, bricklayers and masons use profile boards when constructing houses in areas like Mwanza, Arusha, or Dodoma. For example, a local builder hired to construct a two-bedroom house in a rural village would first set up profile boards around the foundation trench to ensure the walls are perfectly straight and square before laying the first course of bricks or concrete blocks.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools, equipment, and materials
- Cut timber or other materials to the required size
- Assemble boards securely for durability
- Set up boards on-site according to building dimensions
- Inspect boards for stability and alignment
- Ensure compliance with safety standards during the process
Tathmini ya matokeo
Trench excavation is conducted to create the necessary foundation trenches, ensuring safety and accuracy in preparation for construction activities
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain the procedures for making profile boards
Principles: The student should explain the principles involved in making profile boards
Theories: The student should explain
- Importance of profile boards in construction
- Materials used for making profile boards
- Tools and equipment required
- Techniques for making and installing profile boards
- Positioning and aligning profile boards accurately
- Maintenance and reuse of profile boards
Swali
What is the primary purpose of profile boards in construction?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado