Mada za sehemu hiiConstructing sewerage disposalMada 4
Soakaway pits and cesspools are essential on-site wastewater management systems used when buildings are not connected to a main sewer network. A soakaway pit disperses water into the ground, while a cesspool stores sewage for periodic removal. Understanding how to construct these structures is a key skill for masons working in rural and peri-urban areas of Tanzania.
A soakaway pit (also called a soak pit) is an underground reservoir designed to collect and manage rainwater and greywater from sources such as sinks, showers, and storm drains. The structure allows collected water to slowly seep into the surrounding soil, effectively preventing surface flooding and water pooling in yards or streets.
How a Soakaway Pit Works
The operation of a soakaway pit follows a simple but effective process:
- Collection: Water from roofs, driveways, or non-sewage household drains enters the pit through inlet pipes.
- Filtration: The water filters through a gravel- or rubble-filled chamber, which removes debris and regulates the flow rate.
- Percolation: The filtered water slowly percolates through the pit's porous walls and base into the surrounding soil.
- Dispersal: The water eventually merges with groundwater or evaporates over time.
Soakaway pits work best in well-draining sandy or loamy soils. They are typically constructed at depths of 1.5–3 metres to prevent groundwater contamination.
A cesspool (or cesspit) is a sealed underground tank used to store raw sewage until it is periodically pumped out and treated. Unlike soakaway pits that drain wastewater into the soil, a cesspool holds all sewage in a watertight chamber until a licensed vacuum tanker removes the contents.
Key Characteristics of Cesspools
- Sealed structure: Prevents sewage from leaking into the surrounding soil
- No outlet: Unlike septic tanks, cesspools have no outlet pipe to a drain field
- Requires regular pumping: Contents must be removed periodically (frequency depends on household size and usage)
- Vent pipe required: Releases harmful gases produced by decomposing waste
Step 1: Site Selection
Choose a location that meets these minimum distances:
- At least 5 metres from any building foundation
- At least 30 metres from water sources (wells, boreholes, rivers)
- Away from slopes that could cause surface water runoff into the pit
Step 2: Percolation Test
Before construction, conduct a percolation test to determine if the soil can absorb water at an adequate rate:
- Dig a small test hole (300mm × 300mm × 300mm deep)
- Fill with water and allow it to drain completely
- Refill with water and measure the time for the water level to drop 25mm
- Ideal drainage rate: 10–30 minutes per 25mm drop. If drainage is slower than 60 minutes per 25mm, the soil is unsuitable for a soakaway.
Step 3: Excavation
- Dig a pit 1.5–3 metres deep and 1–2 metres wide
- The size depends on the volume of water the pit must handle
- Ensure the sides are vertical and the base is level
Step 4: Lining
- Line the sides with geotextile fabric (if using gravel backfill) to prevent soil particles from clogging the drainage medium
- This step is crucial in sandy soils where fine particles could wash into the gravel
Step 5: Filling with Drainage Material
Fill the pit in layers:
- Bottom 30cm: Coarse aggregate (50–100mm stones)
- Middle section: Medium gravel
- Top 20cm: Finer gravel (10–20mm stones)
This layered approach ensures proper filtration and prevents premature clogging.
Step 6: Installing Perforated Pipes
- Place perforated HDPE or PVC pipes horizontally in the pit if using a chamber system
- Maintain a minimal gradient of 0.5–1% to ensure even water distribution
- Wrap pipes with geotextile fabric to prevent silt intrusion
Step 7: Connecting Inlet Pipe
- Connect the inlet pipe from gutters, drains, or surface water collection points
- Install a debris filter (simple grate or basket) at the inlet to prevent leaves and large particles from entering
Step 8: Covering and Backfilling
- Cover the pit with geotextile fabric to prevent soil intrusion
- Backfill the remaining space with compacted soil
- Ensure the final surface is level with the surrounding ground
Step 9: Testing
- Pour water into the pit and observe the drainage rate
- If drainage is too slow, increase the gravel depth or pit size
- The pit should drain completely within 24–48 hours after heavy rainfall
Step 1: Excavation
- Dig a pit 2–3 metres deep and 1.5–2 metres wide
- The volume should be approximately three times the expected daily wastewater output
- For a typical household, a 3,000–5,000 litre capacity is common
Step 2: Constructing the Walls
Two common construction methods are used:
Method A: Precast Concrete Rings
- Lower precast concrete rings into the pit
- Ensure rings are properly aligned and level
- Seal joints between rings with waterproof mortar
Method B: Brick/Block Walls
- Build walls using bricks or concrete blocks with waterproof mortar (1:3 cement-sand mix with waterproofing additive)
- Apply bitumen coating or waterproof slurry to the exterior surfaces
- Ensure walls are at least 200mm thick for structural strength
Step 3: Sealing Joints
- Seal all joints thoroughly with bitumen or cement-based waterproofing slurry
- This is critical to prevent groundwater contamination and sewage leakage
Step 4: Installing the Inlet Pipe
- Install the inlet pipe from household drains with a sealed entry point
- The inlet should be positioned above the expected liquid level
- Use a rubber gasket or solvent-welded joint for watertight connection
Step 5: Installing the Vent Pipe
- Install a vent pipe at least 100mm in diameter
- Extend the pipe at least 1 metre above ground level
- The vent releases harmful gases (hydrogen sulfide, methane) produced by decomposing waste
Step 6: Installing the Cover
- Place a reinforced concrete lid over the cesspool
- Include a secure access hatch (minimum 600mm × 600mm) for pumping equipment
- The cover must be watertight to prevent surface water entry
Step 7: Backfilling
- Backfill in layers, compacting each layer thoroughly
- Avoid using large rocks or sharp stones that could damage the walls
- Ensure the ground surface is properly graded away from the cesspool
Step 8: Leak Testing
- Fill the cesspool with water and monitor for 24 hours
- Check for any visible water loss or seepage
- Repair any leaks before putting the system into use
| Feature | Soakaway Pit | Cesspool |
|---|---|---|
| Purpose | Disperse water into soil | Store sewage for removal |
| Water type | Rainwater, greywater only | Raw sewage only |
| Outlet | None (water percolates out) | No outlet (sealed) |
| Soil suitability | Best in sandy/loamy soil | Works in any soil |
| Maintenance | Low (occasional debris removal) | High (regular pumping required) |
| Environmental impact | Low (natural filtration) | Higher (requires careful handling) |
| Lifespan | 20–30 years with proper maintenance | Indefinite if maintained |
Soakaway pits are ineffective in clay soils because clay has very low permeability. Water cannot percolate through clay quickly enough, causing the pit to fill up and fail. In clay soils, alternatives such as engineered infiltration systems, raised planted areas, or connection to a municipal sewer network should be considered.
A simple field test: if water stands in a dug hole for more than one hour after heavy rain, the soil is not suitable for a standard soakaway pit.
When constructing either system, observe these safety precautions:
- Excavation safety: Shore or support trench walls when depth exceeds 1.2 metres
- Personal protective equipment: Wear gloves, steel-toe boots, helmet, and safety goggles at all times
- Confined space entry: Never enter a cesspool without proper training, breathing apparatus, and a standby person
- Ventilation: Ensure adequate ventilation when working in enclosed spaces to avoid gas buildup
- Equipment handling: Use proper lifting techniques when handling concrete rings or heavy materials
Soakaway Pit Problems
| Problem | Cause | Solution |
|---|---|---|
| Pit fills but does not drain | Clay soil or clogged gravel | Enlarge pit, replace gravel, or relocate |
| Water backs up during rain | Pit undersized | Increase pit size or add overflow |
| Foul odours | Greywater from kitchen entering pit | Exclude kitchen wastewater; connect to septic system |
Cesspool Problems
| Problem | Cause | Solution |
|---|---|---|
| Rapid filling | High water usage or leak | Reduce usage; check for groundwater infiltration |
| Foul odours | Blocked vent pipe | Clean or replace vent pipe |
| Sewage overflow | Pumped too infrequently | Increase pumping frequency |
| Groundwater contamination | Cracked or leaking walls | Repair with waterproof coating; may require replacement |
In many Tanzanian villages and growing peri-urban areas like Mwananyamala, Kigoma, or Arusha, houses built far from the centralized sewer network rely on soakaway pits for managing bathroom and kitchen greywater, while cesspools or septic tanks handle toilet waste. A mason with skills in constructing these systems can help households maintain proper sanitation, prevent disease spread, and avoid groundwater contamination—services that are increasingly in demand as more families build modern homes with multiple rooms and increased water use.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawing
- Prepare tools, machines and equipment
- Prepare material
- Prepare site
- Perform setting out
- Carry out excavation works
- Prepare the Base
- Construct perforated pit Walls
- Perform curing
- Connect Inlet Pipes
- Backfill the Trench
- Cover the pit
- Clean and store
Tathmini ya matokeo
Soakaway pits and cesspools are constructed as per technical specifications to ensure effective drainage and compliance with environmental regulations
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain different methods for constructing septic tanks and bio digester
Principles: The student should explain the principles involved in constructing soak away pit/cesspool
Theories: The student should explain:
- Types of sewerage disposal
- Connection of pipes
- Constructed sewage disposal
- Construction Materials
- Types of pipe
- Methods of determining gradient Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while constructing sewerage disposal
- Environmental issues
- First aid
Swali
What is the primary function of a soakaway pit in a drainage system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado