Mada za sehemu hiiConstructing hipped roofMada 2
- Constructing multi-hipped/combination roof
- Fixing PVC and steel gutters
A multi-hipped roof (also called a combination roof) is a complex roof structure that combines more than four hip sections meeting at different points, or mixes hip and gable roof designs. These roofs are commonly used in Tanzanian buildings where architects want an attractive appearance combined with good water drainage. The multiple slopes allow rainwater to run off easily from many directions, making them suitable for areas with heavy seasonal rains.
- Hip rafter: The diagonal rafter that runs from the corner of the wall plate to the ridge at a 45° angle
- Jack rafter: A short rafter that runs from a wall plate to a hip or valley rafter
- Valley rafter: The rafter that runs along the internal angle where two roof slopes meet
- Ridge: The horizontal top line where two opposite roof slopes meet
- Cruck: A pair of curved timber pieces forming the main support of a roof
- Purlin: A horizontal beam supporting the rafters
- Double-hip roof: Has four hip ends with the ridge shortened or eliminated
- Triple-hip roof: Features three hip ends, commonly used for L-shaped buildings
- Hip and valley roof: Combines hip sections with valleys cutting into the main roof
- Gambrel roof: A symmetrical two-sided roof with two different slopes on each side (common on traditional houses)
Step 1: Setting Out and Measuring
- Read the building plan to determine roof dimensions and angles
- Use a measuring tape to mark the wall plate positions
- Apply a try square to ensure all corners are at right angles
- Mark the center line where the ridge will run
Step 2: Calculating Rafters
- Measure the run (horizontal distance from wall to ridge center)
- Calculate the rise (vertical height from wall plate to ridge)
- Use the formula: Rafter length=run2+rise2
- For hip rafters, calculate the diagonal: Diagonal run=run×2 (for 45° angles)
Step 3: Cutting Common Rafters
- Cut the common rafters to the calculated length using a hand saw
- Ensure each rafter has a birdsmouth cut to sit on the wall plate
- Use a chisel to trim any excess material for a tight fit
Step 4: Cutting and Fitting Hip Rafters
- Measure and mark the hip rafter length at 45° to the building corners
- Cut the top end to fit against the ridge
- Use a mallet hammer to tap the rafter into position
- Secure with nails driven at an angle (toenailing)
Step 5: Installing Jack Rafters
- Measure distances between hip rafters using a measuring tape
- Cut jack rafters to the correct lengths, starting from the bottom
- Space them evenly according to the specification (usually 400-600mm apart)
- Fix each jack rafter to the wall plate and hip rafter
Step 6: Fixing the Ridge Board
- Position the ridge board at the calculated height
- Use a spirit level to ensure it is perfectly horizontal
- Nail the common rafters to both sides of the ridge
- Check alignment with a manila line stretched across the ridge
Step 7: Installing Purlins and Battens
- Fix purlins at mid-span to support the rafters
- Nail battens across the rafters at specified intervals
- Check all joints are tight and secure
A rectangular classroom building in Arusha measures 8m by 12m with a roof pitch of 30°. The building requires a double-hip roof with a ridge height of 2.5m above the wall plate.
Given:
- Run (half of width) = 8m ÷ 2 = 4m
- Rise = 2.5m
Calculate common rafter length: L=42+2.52=16+6.25=22.25=4.72m
Calculate hip rafter length (diagonal run = 4m × √2 = 5.66m): Hip length=5.662+2.52=32.04+6.25=38.29=6.19m
Therefore, the carpenter needs to cut:
- 12 common rafters at 4.72m each
- 4 hip rafters at 6.19m each
- Multiple jack rafters at varying lengths (decreasing from 2.83m at bottom to zero at top)
- Wear a helmet when working at height
- Use safety boots with steel toes
- Put on leather gloves when handling timber
- Wear safety goggles when cutting wood
- Use a properly secured ladder
- Keep the work area clear of loose timber and tools
In Tanzania, multi-hipped roofs are commonly constructed for modern houses in areas like Masaki, Oysterbay, and high-end developments in Dodoma. A local carpenter working on a clinic or school building in a rainy region like Kagera or Mbeya would use this skill to create durable roofs that can withstand heavy downpours without leaking. Understanding how to calculate rafter lengths and properly fix hip rafters helps carpenters bid accurately for construction jobs, ensuring materials are not wasted and the structure remains stable for decades.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Calculate materials required
- Select tools and materials
- Fix wall plate
- Make trusses
- Erect/fix trusses
- Set and fix purlins
- Cut ends of purlins
- Perform plumb cut of rafters
- Fix fascia boards
- Clean tools
- Store them at safe place
Tathmini ya matokeo
Constructed hipped roof conform to technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The students should be able to state procedures for constructing multihipped/combination roof
Principles: The student should state principles related to constructing multihipped/combination roof
Theories: The students should state the differences between multi-hipped/combination roof
Circumstantial knowledge: Workshop safety rules and regulations
Swali
What is the function of a valley rafter in a multi-hipped roof?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado