Mada za sehemu hiiConstructing roof lightMada 4
- Constructing patent glazing
- Constructing latent glazing
- Constructing sky light
- Constructing dome window
Latent glazing is a type of roof light or skylight that is built into the roof structure to allow natural light into a building while remaining weatherproof. It is constructed as part of the roof itself, with the glazing material (usually glass or transparent sheets) set into a frame that is integrated into the roof covering. In Tanzanian construction, latent glazing is commonly used in warehouses, workshops, schools, and homes to reduce the need for artificial lighting during the day.
Before constructing latent glazing, you must identify and understand each component:
- Frame – The wooden or metal structure that holds the glazing material in place. It is fixed to the roof rafters or purlins.
- Glazing material – The transparent or translucent material that allows light to pass through, such as glass panes, polycarbonate sheets, or clear corrugated sheets.
- Flashing – Material used to make the joint between the frame and the roof watertight, usually made of galvanised iron or lead.
- Beading or sealant – Material used to secure the glazing material in the frame and prevent water leakage.
- Sill – The bottom horizontal part of the frame that collects and directs water away.
- Head – The top horizontal part of the frame.
- Jambs – The vertical sides of the frame.
Follow these steps in order:
-
Take measurements – Use a tape measure to determine the exact size of the opening required in the roof. Mark the positions of the rafters or purlins where the frame will be fixed.
-
Prepare the frame – Cut the timber or metal members to size according to the measurements. The frame should be slightly larger than the glazing material to allow for expansion and fitting.
-
Fix the frame to the structure – Position the frame in the roof opening and secure it to the rafters or purlins using nails or screws. Use a try square to ensure the frame is square and level.
-
Fit the glazing material – Place the glass or transparent sheet into the frame. For glass, use glazing points or clips to hold it in place. For polycarbonate sheets, use appropriate fasteners with washers.
-
Apply sealant and beading – Press glazing sealant around the edges of the glazing material where it meets the frame. Install wooden or metal beading to secure the glazing material firmly.
-
Install flashing – Fix flashing around the perimeter of the frame to create a watertight seal between the frame and the roof covering. Overlap the flashing onto the roof sheets.
-
Check for leaks – Spray water over the completed latent glazing to verify that no water penetrates. If leaks are found, reseal the affected areas.
A workshop in Arusha requires a roof light to provide natural lighting. The opening in the roof is 1.2 metres long and 0.6 metres wide.
Step 1: Measure the opening with a tape measure. The length is 1200 mm and the width is 600 mm.
Step 2: Prepare a timber frame using 50 mm × 25 mm timber. Cut two vertical jambs at 600 mm each and two horizontal members (sill and head) at 1200 mm each.
Step 3: Fix the frame to the roof rafters using 75 mm nails. Check with a try square to ensure the frame is square.
Step 4: Cut a clear polycarbonate sheet to 1180 mm × 580 mm (slightly smaller than the frame to allow fitting). Place it in the frame.
Step 5: Apply silicone sealant around all edges and fix wooden beading with 40 mm nails.
Step 6: Install galvanised iron flashing around the frame, overlapping onto the roof sheets by at least 100 mm.
Step 7: Test by spraying water. No water should enter the workshop.
- Wear safety boots, a safety helmet, and overalls at all times.
- Use a sturdy ladder when working on the roof.
- Handle glass sheets with care to avoid cuts; wear protective gloves.
- Ensure the working area is clear of loose tools and materials.
- Work with a partner when handling long timber or sheet materials.
In Tanzania, latent glazing is frequently used in small businesses such as hardware shops, maize mills, and workshops in towns like Mwanza and Dodoma. For example, a carpenter in Morogoro might install a latent glazing roof light in his workshop to save on electricity costs during the day, as natural illumination allows him to work from morning until evening without using artificial lights, reducing monthly expenses on prepaid electricity.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Calculate materials required
- Select materials and tools
- Set out roof light
- Prepare members
- Make joints
- Fix roof light
- Clean work place and tools
- Store tools in a safe place
Tathmini ya matokeo
Constructed roof lights conform to technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain procedures for constructing latent glazing
Principles: The student should explain principles related to constructing latent glazing
Theories: The students should explain importance of latent glazing
Circumstantial knowledge: Workshop safety rules and regulations
Swali
What is latent glazing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado