Mada za sehemu hiiMaking jointsMada 3
- Constructing framing joints
- Constructing lengthening joints
- Constructing widening joints
A lengthening joint is an end joint used when timber is not long enough for a given task. It joins two pieces of timber end-to-end to make a longer piece suitable for furniture or construction work. The type of lengthening joint chosen depends on the shape, use, appearance, and stability required for the structure.
There are five main types of lengthening joints used in carpentry:
- Butt joint (cleated)
- Scarf joint
- Lap joint
- Finger joint
- Half-lap and sloping halving joint
A butt joint uses short pieces called "cleats" or "fish plates" to hold two timber pieces together end-to-end. A single or double cleat can be used depending on the required strength and whether the joint will be visible.
Steps for Constructing a Butt Joint
| Step | Action |
|---|---|
| 1 | Interpret the working drawing |
| 2 | Select materials as per working drawing |
| 3 | Select tools: tenon saw, tape measure, try square, marking gauge, claw hammer, pencil, F-clamp, workbench |
| 4 | Draw square lines on the joint ends |
| 5 | Cut ends of joint pieces square |
| 6 | Prepare the cleat(s) according to joint size |
| 7 | Assemble the joint |
| 8 | Check accuracy: squareness and straightness |
| 9 | Return tools to the tool store |
| 10 | Clean the workplace |
A scarf joint is made by cutting the ends of both timber pieces at an angle (slope) and joining them together. For structural use, the slope should be 1 in 12 or less. A hooked scarf joint uses folding wedges to tighten the joint.
Steps for Constructing a Scarf Joint
| Step | Action |
|---|---|
| 1 | Interpret the working drawing |
| 2 | Select materials as per working drawing |
| 3 | Select tools: cross-cut saw, tape measure, try square, sliding bevel, claw hammer, pencil, F-clamp, workbench |
| 4 | Set out the joints as per drawing |
| 5 | Cut joint pieces as per setting out |
| 6 | Assemble the joint |
| 7 | Check accuracy: tightness and straightness |
| 8 | Return tools to the tool store |
| 9 | Clean the workplace |
A lap joint is formed by overlapping two timber pieces at their ends. This increases the length of the member while providing good strength through the large gluing area.
Steps for Constructing a Lap Joint
| Step | Action |
|---|---|
| 1 | Interpret the working drawing |
| 2 | Select materials as per working drawing |
| 3 | Select tools: cross-cut saw, tape measure, try square, claw hammer, pencil, F-clamp, workbench |
| 4 | Measure and mark the overlap length |
| 5 | Cut and trim the joint areas |
| 6 | Assemble the joint |
| 7 | Check accuracy: squareness and straightness |
| 8 | Return tools to the tool store |
| 9 | Clean the workplace |
A finger joint is made by cutting interlocking "fingers" into the ends of two timber pieces. This joint is useful for using short pieces of timber and creating a strong bond. The fingers interlock and are glued together under pressure.
Steps for Constructing a Finger Joint
| Step | Action |
|---|---|
| 1 | Interpret the working drawing |
| 2 | Select materials as per working drawing |
| 3 | Select tools: tenon saw or cross-cut saw, tape measure, try square, marking gauge, chisels, mallet hammer, pencil, F-clamp, workbench, claw hammer |
| 4 | Measure and set finger positions |
| 5 | Cut and chop the finger profiles |
| 6 | Assemble the joint with glue |
| 7 | Check accuracy: squareness and straightness |
| 8 | Return tools to the tool store |
| 9 | Clean the workplace |
A half-lap joint involves removing half the thickness from each board so they can be joined to form a piece with uniform thickness. This joint is commonly used for increasing the length of roofing and floor wall plates. The strength comes from the long grain on the mating surfaces.
Steps for Constructing a Half-Lap Joint
| Step | Action |
|---|---|
| 1 | Interpret the working drawing |
| 2 | Select materials as per working drawing |
| 3 | Select tools: cross-cut saw, tape measure, try square, marking gauge, chisels, mallet hammer, pencil, F-clamp, workbench, claw hammer |
| 4 | Measure and mark the half-lap position on both pieces |
| 5 | Cut and remove half the thickness from each piece |
| 6 | Assemble the joint |
| 7 | Check accuracy: squareness and straightness |
| 8 | Return tools to the tool store |
| 9 | Clean the workplace |
A carpenter in Arusha needs to make a 3-meter-long table leg but only has two pieces of timber, each 1.5 meters long. The carpenter decides to use a scarf joint.
Solution:
- Calculate the slope: A proper scarf joint requires a slope of 1:12. For a 3-meter (300 cm) joint, the overlap should be at least 300 ÷ 12 = 25 cm.
- Cut both timber ends at the required angle using a cross-cut saw and sliding bevel.
- Apply wood glue to the cut surfaces.
- Join the pieces and clamp with F-clamps until the glue dries.
- Check that the completed joint is straight using a try square.
- Always wear safety boots and overalls in the workshop.
- Use a bench vice or bench hook when holding workpieces.
- Keep chisels sharp and cut away from your body.
- Return all tools to their proper storage after use.
- Keep the workshop clean to prevent accidents.
In Tanzania, a carpenter in Dar es Salaam constructing a long dining table for a customer would use lengthening joints when the available timber is shorter than required. For example, if a customer orders a 2.4-meter-long table top but the timber dealer only has 1.2-meter planks, the carpenter can join two pieces using a finger joint or tongue-and-groove joint to achieve the desired length while maintaining strength and a neat appearance. This skill is essential for small carpentry workshops across Tanzania that often work with limited timber sizes.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Draw joints
- Interpret drawing
- Calculate materials required
- Take measurements
- Set joint position
- Prepare joint members
- Assemble joints
- Perform general finishing
- Clean the work piece and work place
- Store the work piece, tools, and equipment to a safe place
Tathmini ya matokeo
A workpiece constructed with lengthening joints conforms to the drawing and technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student be able to should explain methods related to construct lengthening Joints
Principles: The student should explain principles related to construct lengthening Joints
Theories: The students should explain theories related to construct lengthening Joints
Circumstantial knowledge: The students should explain detailed knowledge related to construct lengthening Joints
Swali
What is the main purpose of a lengthening joint in carpentry?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado