Sonzaschool
Rudi

Sekondari ya Kawaida · Kidato cha Pili · Amali · Civil Engineering

Carpentry and Joinery With Metal Works

Making a door frame

takriban dakika 5 kusoma

Majadiliano
Mada za sehemu hiiMaking door frame and window framesMada 3

Making a Door Frame

A door frame is a structural wooden framework that surrounds and supports a door opening in a building. It provides the necessary support for the door shutter to swing open and closed, while also giving the opening a finished appearance.

Parts of a Door Frame

A standard door frame consists of six main components:

  • Head – The horizontal top member that sits above the door opening, providing structural support and keeping the door aligned.
  • Jambs – The two vertical side pieces (latch side and hinge side) that run along the sides of the door. The hinge side supports the door hinges, while the latch side holds the lock mechanism.
  • Sill or Threshold – The bottom horizontal member that sits at the base of the door. It may be omitted when the floor itself acts as the sill.
  • Mullion – A vertical element that separates multiple door units or panes within a single frame.
  • Transom – A horizontal member that separates door shutters when the door opening exceeds 2100mm in height.
  • Horn – A horizontal projection at the top and bottom of the frame (typically 100mm to 150mm long) that enables fixing the frame securely into the wall opening.

Joints Used in Door Frame Making

Two main joints are commonly used:

  1. Mortise and Tenon Joint – This joint consists of a protruding tenon on one piece that fits into a corresponding recess (mortise) on another piece. It is highly durable and strong, ideal for traditional high-quality door frames.

  2. Long and Short Shoulder Mortise and Tenon Joint – Used when a rebate is required. One piece is set parallel to the grain to cover the rebate, while another piece slides into the jamb member.

The Rebate

A rebate is a depression or recess cut along the edge of the frame members. The door shutter is fixed to the rebate using hinges. The standard rebate width is 12mm, and its depth equals the thickness of the door shutter.

Materials Required

  • Timber for frame members
  • Wood glue
  • Nails or screws
  • Sandpaper
  • Sanding sealer and thinner

Tools and Their Uses

ToolPurpose
Measuring tapeMeasuring distance and dimensions
Pencil or marking knifeMarking measurements and cutting lines
Try squareChecking right angles and squareness
Hand sawCutting timber to size
Jack planeSmoothing and truing timber surfaces
Rebate planeCutting rebates or rabbets in timber
Claw hammerDriving or removing nails
ScrewdriverInstalling or removing screws
Mortise chiselChopping mortise recesses
Hand drillCreating pilot holes for nails or screws
PaintbrushApplying paint or stain
Workbench with viceSupporting woodwork operations

Procedures for Making a Door Frame

Follow these steps in order:

1. Planning and Measuring

  • Interpret working drawings or specifications
  • Measure the height and width of the door opening
  • Determine the thickness and width of frame pieces based on door and wall dimensions

2. Cutting Timber

  • Measure and cut two pieces for the jambs
  • Measure and cut one piece for the head
  • Cut a bottom piece for the sill or threshold (if required)
  • Cut transom if door height exceeds 2100mm

3. Planing Timber

  • Plane all parts for face side (flat, straight surface)
  • Plane for face edge (correct edge for width)
  • Plane to required thickness
  • Rip timber to required width

4. Making Rebates

  • Measure and mark the rebate dimensions (12mm wide standard)
  • Cut along marked lines
  • Use rebate plane to level and smooth the rebate

5. Preparing Joints

  • Mark and chisel out mortises at the ends of the head
  • Cut tenons at the ends of jambs where they meet the head
  • For rebate frames, cut long and short shoulder tenons

6. Trial Assembly

  • Assemble frame pieces without glue or nails
  • Check for fit and make adjustments as needed

7. Final Assembly

  • Apply wood glue to joints (if required)
  • Align mortises and tenons
  • Secure with nails or screws
  • Use try square to check squareness

8. Finishing

  • Fill gaps, nail holes, or imperfections with wood filler
  • Once dry, sand smoothly (start with rough grit, finish with fine)
  • Apply paint or stain as desired
  • Allow to dry completely

9. Cleanup

  • Clean the workplace
  • Return tools to storage

Safety Precautions

Always observe the following safety measures:

  • Wear Personal Protective Equipment (PPE): safety goggles, ear plugs, and gloves
  • Use tools properly according to their intended purpose
  • Keep the working area clean and organized
  • Ensure good ventilation when applying finishes

Real-life application

In Tanzania, carpenters use these door frame making skills in everyday construction work. For example, a local carpenter in Mwanza or Dar es Salaam would apply these procedures when building door frames for a new house, using locally available tools and timber from hardware shops. A standard door frame made by a skilled carpenter might cost around TZS 50,000 to 80,000 in material costs, and the ability to make quality door frames is a valuable skill for both employed carpenters and those running their own small woodworking businesses in communities across Tanzania.

Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa

Tathmini ya mchakato

The student should be able to:

  • Draw door frames
  • Interpret the drawings
  • Calculate materials required
  • Select tools and materials
  • Cut and plane timber to required size/measurement
  • Make rebate
  • Mark/set joints position
  • Chop mortises
  • Cut tenon
  • Assemble the frame
  • Clean the work place and tools
  • Store the frame and tool properly

Tathmini ya matokeo

Door frames constructed as per the drawing and technical specifications

Tathmini ya maarifa

Detailed knowledge of:

Method used: The student should be able to explain methods related to making door frames

Principles: The student should explain principles for making a door frame

Theories: The students should explain theories related to making a door frame

Circumstantial knowledge: The students should explain detailed knowledge related to make door frame

Swali

Which component of a door frame is the horizontal member that sits above the door opening?

Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.

Ingia ili kufanya mazoezi

Mwalimu

Umekwama? Niulize chochote kuhusu mada hii.

Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.

Ingia ili kuuliza

Majadiliano

Hakuna maswali bado

Ingia ili kuuliza
Inapakia majadiliano…