Mada za sehemu hiiFabricating aluminium/PVC doorsMada 2
- Fabricating aluminium/PVC door frames
- Fabricating aluminium/PVC door shutters
Aluminium and PVC door frames are structural components used to support doors within wall openings. They are lightweight, durable, corrosion-resistant, and provide good thermal insulation, making them ideal for both residential and commercial buildings in Tanzania.
The main parts of an aluminium/PVC door frame are:
- Side jambs: The vertical members on either side of the frame
- Head: The top horizontal member of the frame
- Threshold (sill): The bottom horizontal member that sits on the floor
- Transom: An optional horizontal member that divides the frame (used when there are windows above the door)
Common door frame types include:
- Door frame with jamb, head, and threshold
- Door frame with jambs, head, transom, and threshold
- Door frame with a side window
- Door frame with double-sided windows
- Lightweight yet strong and durable — do not warp or bend over time
- Corrosion resistant — aluminium forms a protective oxide layer; PVC resists moisture and decay
- Good thermal insulation — helps improve energy efficiency
- Easy to clean and maintain — requires minimal care compared to wood or steel
- Available in various colours and finishes for aesthetic flexibility
Step 1: Planning and Measurement
- Measure the wall opening width and height
- Start with width, then height, then depth (if applicable)
- Select the appropriate frame type based on the door design
- Prepare the aluminium/PVC profiles and cut them to required sizes
Step 2: Cutting Aluminium Profiles
- Use a hacksaw or mitre saw with fine-tooth blade (32 TPI for aluminium)
- Cut profiles to specified dimensions for head, sill, and jamb
- Clean the edges to remove burrs using a file or deburring tool
- Ensure smooth edges for easy assembly
Step 3: Assembling the Door Frame
- Lay out frame components (head and jamb profiles) on a flat surface
- Join corners using either:
- Mitre joints (45° angle cuts) — provides seamless appearance
- Butt joints — simpler but less aesthetic
- Use screws, bolts, or corner brackets to secure joints
- Check alignment and squareness using:
- Measuring tape
- Set square
- Spirit level
- Verify squareness by comparing diagonal measurements (must match within ±2 mm)
Step 4: Attaching the Frame to the Wall Opening
- Position the assembled frame in the partition opening
- Ensure the frame is level and flush with the wall
- Use plastic or wooden shims for alignment
- Secure with anchor bolts (brick walls) or screws (drywall)
- Double-check alignment before final tightening
Step 5: Cleaning and Storage
- Apply silicone sealant around edges for weatherproofing
- Install rubber gaskets for sealing
- Remove protective film from profiles
- Clean the working place and store tools properly
Given: Wall opening = 900 mm (width) × 2100 mm (height)
Step 1: Calculate frame dimensions (with 5 mm total clearance)
- Head/sill length = 900 mm − 10 mm = 890 mm
- Jamb length = 2100 mm (full height, no deduction)
Step 2: Cutting list
| Component | Quantity | Length |
|---|---|---|
| Head (top) | 1 | 890 mm |
| Sill (bottom) | 1 | 890 mm |
| Jambs (vertical) | 2 | 2100 mm |
Step 3: Assembling
- Cut four pieces: 2 × 890 mm and 2 × 2100 mm
- Use mitre joints (45° cuts) at corners
- Secure with corner brackets and screws
- Check diagonals: both should equal approximately 2136 mm
- Calculation: √(890² + 2100²) = √(792100 + 4410000) = √5202100 ≈ 2281 mm
Wait, let me recalculate: √(890² + 2100²) = √(792100 + 4,410,000) = √5,202,100 ≈ 2281 mm
Actually, diagonal = √(width² + height²) = √(890² + 2100²) ≈ 2281 mm
The two diagonals must match within ±2 mm tolerance.
- Wear safety goggles and gloves when cutting aluminium
- Use dust mask when cutting PVC
- Ensure proper ventilation
- Secure workpieces with clamps before cutting
- Deburr all cut edges to prevent injuries
In Tanzania, aluminium door frames are commonly used in modern shops, offices, and homes in urban areas like Dar es Salaam and Arusha. A small business owner fabricating and installing aluminium door frames can charge between TSh 150,000 to TSh 350,000 per frame for standard doors (900 mm × 2100 mm), depending on the profile quality and location — making this skill valuable for income generation in the growing construction sector.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Draw
- Interpret drawings
- Calculate materials required
- Select tools and materials
- Prepare members
- Set members
- Make joints
- Assemble door frames
- Clean work place and tools
- Store tools to a safe place
Tathmini ya matokeo
Fabricated aluminium and PVC doors frames conform to given technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain methods related to fabricate aluminium/PVC door frames
Principles: The student should explain principles related to fabricate aluminium/PVC door frames
Theories: The students should explain theories related to fabricate aluminium/PVC door frames
Circumstantial knowledge: The students should explain detailed knowledge related to fabricate
Swali
What is the name of the bottom horizontal member of an aluminium/PVC door frame?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado