Mada za sehemu hiiPerforming machine operationsMada 3
- Performing metal grinding
- Performing hole drilling
- Performing thread-cutting
Thread-cutting is the process of forming a spiral groove (thread) on the outside of a rod or pipe, or inside a hole, so that a matching bolt or pipe fitting can be screwed into it. In electrical installation, threads are cut on steel conduit so that lengths can be joined with couplers or connected to metal boxes. Plastic (PVC) conduit is not threaded; it is joined with push-fit or solvent-welded fittings.
There are two main types of threads you will work with:
- External threads – threads cut on the outside surface of a pipe or rod
- Internal threads – threads cut on the inside surface of a hole or fitting
Threads are also classified by their shape:
- V-shaped threads – the standard thread profile
- Square threads – used for power transmission
- Buttress threads – designed to carry load in one direction
- Die – a hardened steel ring with cutting teeth on the inside. It cuts external threads. One face has a tapered lead so that the die starts easily; that face goes onto the work first.
- Die stock – holds and turns the die. Its main parts are the body with a seat for the die, two handles, the screws that lock and adjust the die and, on conduit stocks, a guide that keeps the die square to the pipe.
- Taps – hardened steel tools with cutting threads on the outside. They cut internal threads and are used as a set of three: the taper tap starts the thread, the second tap deepens it and the plug tap finishes it to the bottom of the hole. The main parts of a tap are the square end, the shank, the threaded body and the flutes that carry the chips away.
- Tap wrench – grips the square end of the tap and has two handles for turning it.
- Threading machine – a power-driven machine for pipe and conduit. A chuck grips and turns the pipe while a die head cuts the thread. Most machines also have a pipe cutter, a reamer and an oil feed.
Before starting any thread-cutting work, gather these tools and equipment:
| Tool | Purpose |
|---|---|
| Threading machine or die and die stock | To cut the thread |
| Workbench | Stable working surface |
| Oil can | Lubricates the cutting tool |
| Radius gauges | Check rounded corners and curves on a workpiece |
| Thread (screw pitch) gauge | Checks the pitch and form of the thread |
| Steel rule | Measures the workpiece and the length of thread |
| Triangular file and flat file | Mark the start grooves; remove burrs and sharp edges |
| Reamer or round file | Removes the burr inside a conduit |
| Hacksaw | Cuts the pipe or rod to length |
| Spring divider | Marks and measures distances |
| Scriber | Marks lines on metal |
| Scriber surface table | Flat surface for marking |
| Pipe vice | Holds the pipe securely |
Always wear the following personal protective equipment:
- Leather gloves – protect hands from sharp metal edges when handling and carrying cut metal. Take them off when you use a power threading machine, because a glove can be caught by the turning pipe
- Overalls – protect your body
- Safety boots – protect feet from heavy objects
- Safety glasses – protect eyes from metal chips
Button your sleeves and tie back long hair. Loose clothing can be caught by a threading machine.
- Interpret the drawing – Read the drawing to find the material, the diameter and length of the workpiece, and the size and length of thread required.
- Select the material, tools and equipment – Choose a straight, undamaged pipe or rod and a die of the same size as the thread on the drawing (for example, 20 mm or 25 mm for steel electrical conduit).
- Mark the workpiece – Use the steel rule, scriber and spring divider to mark the length of the workpiece and the point where the thread must end.
- Clamp the workpiece – Clamp the pipe or rod firmly in the vice, with the end to be threaded sticking out just far enough to work on. Use a pipe vice for conduit so that the pipe is not crushed. Make sure it cannot turn while cutting.
- Mark the start grooves – With the triangular file, file a small groove on each mark. The groove is easy to see when the work is covered with oil, and it gives the hacksaw a clean start when you cut to length. Then file the end square and file a small chamfer (bevel) around it so that the die starts squarely.
- Apply cutting oil – Lubricate the end to be cut with oil from the oil can. This reduces friction and heat and gives a smoother thread.
For External Threads (using a die)
- Mount the correct die in the die stock, with the tapered lead side facing the work.
- Position the die squarely over the end of the pipe.
- Turn the die stock clockwise, pressing it steadily and squarely onto the end of the work until the die begins to cut.
- After each full turn, turn the die back about a quarter of a turn to break the chips, and apply more cutting oil as you go.
- Continue until you reach the marked length.
- Remove the die by turning it anticlockwise. Clear the chips with a brush, never with your fingers, because they are sharp.
- Use a thread gauge to verify the thread is correctly formed.
For Internal Threads (tapping)
- Drill a hole of the correct tapping size, which is smaller than the thread diameter (for example, a 5 mm hole for an M6 thread).
- Mount the correct tap in a tap wrench.
- Start with the taper tap. Keep it square to the work, turn it clockwise with steady pressure, and turn it back a quarter of a turn after each turn to break the chips. Never force a tap, because taps are brittle and snap easily.
- Apply cutting oil regularly.
- Continue until the tap reaches the desired depth, then repeat with the second tap and the plug tap.
- Remove the tap carefully.
An electrician needs to join two pieces of 20 mm steel conduit to run wiring along a workshop wall. Each piece is 1 metre long, but the run is 1.8 metres, so one piece must be cut to 0.8 metres (1.8 − 1 = 0.8). The electrician will:
- Read the drawing to find the lengths and the length of thread needed, about 15 mm on each end to be joined (half the length of a coupler).
- Mark the second piece at 0.8 metres, clamp it in the pipe vice and cut it square with a hacksaw.
- File the cut end square and ream the inside to remove the burr.
- Fit a 20 mm die in the die stock, with the tapered lead side facing the conduit.
- Apply cutting oil to the end of the conduit.
- Turn the die stock clockwise, turning back a quarter of a turn after each turn, until about 15 mm of thread is cut.
- Remove the die, brush off the chips, wipe off the oil and ream the inside of the conduit again.
- Screw a coupler halfway onto the first piece, then screw the second piece into the other half until the two ends meet inside the coupler.
The finished joint is mechanically strong and gives a continuous metal path along the conduit. This matters because steel conduit must be earthed along its whole length. The smooth, reamed ends protect the insulation of the cables that are drawn in.
A sawn end and a freshly cut thread have sharp burrs. Remove the burr on the outside of the end with a flat file, using light strokes. Remove the burr inside a conduit with a reamer or a round file. This is very important in electrical work, because a burr inside the conduit can cut the insulation of the cables as they are drawn in.
After cutting, always inspect and measure your work:
- The thread should be clean and complete along the entire marked length.
- A nut or coupler should screw on smoothly by hand for external threads.
- A bolt should fit snugly for internal threads.
- There should be no burrs or rough edges.
- The length of thread, measured with the steel rule, should match the drawing.
- The blade of the thread gauge with the correct pitch should sit in the thread with no light showing under it.
If the thread is torn or incomplete, cut off the damaged end and start again with a sharp die or tap and more cutting oil.
Steel conduit is sized by its outside diameter in millimetres. The thread has the same nominal diameter and a pitch of 1.5 mm.
| Conduit Size | Thread | Common Use |
|---|---|---|
| 16 mm | M16 × 1.5 | Short runs with one or two small cables |
| 20 mm | M20 × 1.5 | Most lighting and socket circuits |
| 25 mm | M25 × 1.5 | Runs carrying more or larger cables |
| 32 mm | M32 × 1.5 | Main and sub-main cables |
- Mild steel (steel conduit, rods and bolts) is strong and tough but soft enough to cut with a die. It rusts, so conduit is galvanised or enamelled. Cutting a thread removes this coating, so paint any bare thread that is left showing after assembly.
- Brass and copper are softer than steel, cut easily and do not rust.
- Aluminium is light and soft. It tends to clog the die, so clear the chips often.
- Cast iron is hard but brittle and is usually threaded dry.
- Tool steel, used for dies and taps, is much harder than the metal being cut, but it is brittle. A tap or die that is forced or dropped can chip or snap.
- Keep your hands away from the turning pipe and die head of a threading machine. Switch it off before you measure the work or clear chips.
- Clear chips with a brush, never with bare hands or by blowing.
- Wipe up spilt oil at once so that nobody slips.
- When you finish, brush the chips out of the die, taps, vice and machine, and sweep the bench and floor. Put metal chips and oily rags in the correct waste containers.
- Wipe the workpiece clean of oil and chips.
- Wipe the tools, oil them lightly to prevent rust, and store dies and taps in their box so that the cutting edges do not knock against each other.
- Check tools regularly. Replace blunt or chipped dies and taps, keep the vice screw clean and oiled, and keep the oil in the threading machine topped up.
In Tanzania, an electrician working on a new house in Arusha needs to install steel conduits from the main switchboard to each room. When a conduit run goes around a corner or through a wall, the electrician must cut threads on the conduit ends and use couplers or elbows to make firm connections. This ensures that the cables are safely enclosed and protected from damage, and that the steel conduit forms one continuous earthed run, throughout the life of the building.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret the drawing.
- Select the material, tools, and equipment.
- Mark the workpiece.
- Clamp the workpiece on a vice.
- Mark the start grooves with a triangle file.
- Perform thread cutting.
- Remove sharp edges with a file.
- Measure accuracy.
- Apply safety measures.
- Clean the workplace, work pieces, and tools.
Tathmini ya matokeo
Thread-cutting is performed as per technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of: the method used. The student should explain how to perform thread-cutting.
Principles: The student should explain principles related to performing thread-cutting.
Theories: The trainee should explain:
- Types of thread-cutting tools and their functions.
- Main parts of a thread-cutting tool.
Circumstantial knowledge:
Detailed knowledge about:
- Preventive maintenance of tools, equipment, and machines
- Properties of metal material
Swali
Why are threads cut on the ends of steel conduit in electrical installation?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado