Mada za sehemu hiiPerforming surface finishing operationsMada 3
- Carrying out sanding
- Carrying out filing
- Carrying out reaming
Carrying Out Reaming
Reaming is a surface finishing operation that improves the quality of a drilled hole. It smooths the inner surface of a hole and brings it to a more accurate size. When you drill a hole, it is impossible to make it perfectly smooth and accurate; therefore, reaming is done to achieve the required precision for mechanical fittings.
Reaming is the process of smoothing and sizing a drilled hole to make it accurate and smooth. The holes we drill with a drill bit are never perfectly round or smooth enough for precision work. When an accurate hole is needed, such as for fitting bearings or bolts, we use a reamer to improve the hole quality. Hand reamers have a square end for turning with a wrench, while machine reamers have either a straight or tapered shank for use in drilling machines.
- Reamer: The main tool used to improve hole accuracy and reduce surface roughness
- Bench vice: Used to securely hold the workpiece
- Cutting fluid: Lubricant used during reaming to reduce friction and heat
- Steel rule or caliper: For measuring hole diameter

Follow these steps carefully to perform reaming correctly:
-
Drill the pilot hole — Drill the hole approximately 1.0 mm under the required size. This allows the reamer to remove only a small amount of material.
-
Secure the workpiece — Clamp the work piece firmly in a bench vice with the hole in a vertical position.
-
Apply cutting fluid — Lubricate the reamer and the hole with cutting fluid to prevent overheating and ensure smooth cutting.
-
Position the reamer — Hold the reamer at right angles (90°) to the surface of the workpiece. Apply slight downward pressure.
-
Turn the reamer clockwise — Rotate the reamer slowly and evenly, making sure it stays aligned with the hole. Continue turning until the reamer has passed completely through the hole.
-
Remove the reamer properly — Keep rotating the reamer clockwise as you withdraw it from the hole. Never turn the reamer backwards, as this will damage both the tool and the workpiece.
-
Check the measurement — Verify that the hole size meets the required specifications.
-
Clean the workpiece — Remove all swarf and cleaning the workpiece and work area.
- Always wear safety glasses to protect your eyes from metal chips
- Ensure the workpiece is firmly secured in the vice before reaming
- Apply cutting fluid to prevent overheating
- Turn the reamer only in the clockwise direction — never reverse while inside the hole
- Keep fingers away from the reamer while it is rotating
A student needs to prepare a hole for an M10 bolt in a metal plate. The bolt requires a 10 mm diameter hole, but after drilling, the hole measures 9.0 mm.
Solution: The student should:
- Select a 9.0 mm drill bit and drill the pilot hole
- Secure the plate in the vice
- Apply cutting oil to the reamer
- Use a 10 mm hand reamer to enlarge the hole
- Turn the reamer clockwise while applying light pressure
- Continue until the reamer passes through completely
- Measure the finished hole — it should now be approximately 10 mm in diameter
The reaming operation removes approximately 0.5 mm from each side of the hole, bringing it to the correct size for the M10 bolt.
Why is it necessary to ream a hole instead of drilling it to the exact size?
Reaming provides a smoother surface finish and more accurate dimensions than drilling alone. It corrects slight inaccuracies from drilling and produces a hole that fits fasteners more precisely.
In Tanzanian electrical workshops, reaming is used when installing conduits and junction boxes. For example, when mounting a distribution board, holes must be accurately sized to fit the mounting screws or bolts securely. A properly reamed hole ensures that screws hold tightly, preventing the board from becoming loose and causing electrical hazards. This skill is essential for safe and professional electrical installation work in homes, schools, and businesses across Tanzania.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret the technical drawing.
- Select the material, tools and equipment for reaming.
- Clamp the work piece.
- Perform reaming.
- Take measurement for accuracy.
- Apply safety measures.
- Clean the work place and work piece.
- Store the work piece, tools and equipment.
Tathmini ya matokeo
A work piece reamed as per technical specifications.
Tathmini ya maarifa
Methods used: The student should explain how to carry out reaming.
Principles: The student should explain principles related to reaming.
Theories: The trainee should explain:
- Advantages of reaming.
- Types of reamer.
Detailed knowledge about:
- Safety requirements
- Properties of materials
- Mechanical and electrical hazards while reaming
Swali
What is the main purpose of reaming in metalwork?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado