Mada za sehemu hiiDetermining characteristics of active electronic componentsMada 3
- Testing characteristics of diodes
- Testing characteristics of transistors
- Testing characteristics of thyristor
A transistor is a small electronic component that controls the flow of electric current in a circuit. It acts like an electronic switch or amplifier — it can turn a current on or off, or make a small signal stronger. Transistors are used in almost all modern electronic devices, from radios and televisions to phone chargers and control systems.

The two most common types of transistors are:
- NPN Transistor — Current flows from the Collector (C) to the Emitter (E) when a small current is applied to the Base (B).
- PNP Transistor — Current flows from the Emitter (E) to the Collector (C) when a small current is applied to the Base (B).
Each transistor has three legs ( terminals): Base (B), Collector (C), and Emitter (E). Identifying these terminals is the first step in testing.
Transistors can become faulty due to overheating, physical damage, or aging. Testing a transistor tells you whether it is:
- Good — working properly
- Shorted — conducting all the time (leaking between terminals)
- Open — not conducting at all (broken inside)
To test a transistor, you need:
- A digital multimeter (with diode test or transistor test mode)
- The transistor to be tested
- A breadboard or test board (optional)
- Safety goggles and gloves
Follow these steps carefully:
Step 1: Identify the Transistor Type
Check the part number on the transistor and confirm whether it is NPN or PNP using a datasheet or reference guide.
Step 2: Set the Multimeter
Turn your multimeter to the diode test mode (or transistor hFE mode if available).
Step 3: Test the Base-Emitter Junction
- Place the red (positive) multimeter lead on the Base (B).
- Place the black (negative) lead on the Emitter (E).
- For an NPN transistor, you should get a reading between 0.5V and 0.8V.
- For a PNP transistor, you should get a reading between 0.5V and 0.8V when the leads are reversed.
Step 4: Test the Base-Collector Junction
- Place the red lead on the Base (B).
- Place the black lead on the Collector (C).
- You should get a similar voltage reading (0.5V to 0.8V) as in Step 3 for a good transistor.
Step 5: Test for Short Circuits
- Place the black lead on the Base (B) and the red lead on the Emitter (E).
- For both NPN and PNP transistors, the multimeter should display OL (Over Limit) or 1, meaning no current flows in this direction.
- Repeat with the Collector (C) terminal. You should also get OL or 1.
Step 6: Interpret the Results
| Test Point | Good Transistor | Faulty Transistor |
|---|---|---|
| Base to Emitter | 0.5V – 0.8V | 0V (open) or 0V (shorted) |
| Base to Collector | 0.5V – 0.8V | 0V (open) or 0V (shorted) |
| Collector to Emitter | OL or 1 | 0V (shorted) |
If any reading is 0V (shorted) in both directions, the transistor is damaged and must be replaced.
- Always wear safety goggles when working with electronic components.
- Ensure the power supply is switched off before removing or inserting transistors.
- Handle transistors gently — the legs bend easily.
- Work in a well-lit area to avoid mistakes.
In Tanzania, transistors are found in everyday devices such as radio receivers in rural shops, phone charging adapters, and simple amplifier circuits used in community PA systems. If a technician at a repair shop in Mwanza or Dar es Salaam receives a non-working radio, they will use a multimeter to test the transistors inside, following the same steps above, to find which one is faulty and replace it — restoring the radio to working condition for a customer.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- The student should be able to:
- Select tools, equipment, safety gear, and components.
- Construct circuit.
- Connect test equipment.
- Perform component characteristics test.
- Record test results.
- Observe safety measures.
- Clean workplace.
- Store tools, equipment, safety gear, and components.
Tathmini ya matokeo
Transistor test results conform to the standard characteristics.
Tathmini ya maarifa
Knowledge evidence:
Methods used: The student should explain how to test the characteristics of the transistor.
Principles: The student should explain the principles related to testing characteristics of a transistor.
Theories: The trainee should explain: -
- Semiconductor devices.
- The PN junction.
- Properties of semiconductors.
Circumstantial knowledge:
Detailed knowledge about: Semiconductors and their characteristic
Swali
What are the three terminals of a bipolar junction transistor (BJT)?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado