Mada za sehemu hiiDetermining characteristics of active electronic componentsMada 3
- Testing characteristics of diodes
- Testing characteristics of transistors
- Testing characteristics of thyristor
A thyristor is a semiconductor device that acts like a controlled switch — it turns ON when a small trigger voltage is applied to its gate terminal and stays ON until the main current is reduced to zero. In this activity, you will learn how to identify a thyristor and test its basic characteristics using simple equipment.

A thyristor (also called SCR — Silicon Controlled Rectifier) is an electronic component with three terminals:
- Anode (A) — the positive terminal
- Cathode (K) — the negative terminal
- Gate (G) — the control terminal that triggers the device
The thyristor has two states: OFF (no current flows) and ON (current flows). Once triggered ON, it stays ON even after the gate signal is removed, until the current through it drops to zero.
Before testing, you must identify the three terminals using a multimeter:
- Set the multimeter to diode testing mode.
- Place the red (positive) probe on one terminal and touch the black (negative) probe to each of the other two terminals.
- The terminal that gives a reading (typically 0.6V to 1.2V) with both other terminals is likely the cathode.
- The other two terminals are the anode and gate. Use the diode test between suspected gate and cathode — a small forward voltage drop indicates the correct gate-cathode pair.
Equipment needed
- Thyristor (e.g., BT151 or similar)
- DC power supply (9V or 12V)
- Switch (push-button)
- Resistor (e.g., 1kΩ for gate protection)
- LED or small bulb as indicator
- Multimeter
- Connecting wires
- Safety gear: gloves, goggles, overalls
Test procedure
-
Safety first — wear gloves, goggles, and overalls before handling live circuits.
-
Build the test circuit:
- Connect the anode of the thyristor to the positive terminal of the power supply.
- Connect the cathode to one side of the LED (or bulb), then to the negative terminal of the power supply.
- Connect a push-button switch between the gate and anode through a 1kΩ resistor.
-
Test OFF state: With the push-button not pressed, the LED should be OFF. Use the multimeter to confirm no current is flowing (set to DC current mode in series with the LED).
-
Test ON state: Press and release the push-button. The LED should light up and stay ON even after releasing the button. This shows the thyristor has latched.
-
Turn OFF: Disconnect the power supply or remove one wire to break the circuit. The LED goes OFF, and the thyristor resets.
Expected observations
- When the gate trigger is applied, the thyristor turns ON and the LED glows.
- The LED remains ON (latched) without continuous gate signal.
- Removing the main current resets the thyristor to OFF.
Suppose you have a 12V DC supply and a thyristor connected to a 12V, 100mA LED with a 1kΩ gate resistor. When you press the push-button:
Vgate=1000Ω12V=12mA
This 12mA gate current is enough to trigger the thyristor into conduction. The LED lights up at about 100mA and stays ON until you disconnect the 12V supply.
- The gate terminal controls the thyristor — a small current at the gate switches it ON.
- Once ON, a thyristor stays ON until the main current is stopped.
- Always use a resistor in series with the gate to protect the thyristor from damage.
- Use safety equipment when testing any electronic circuit with live voltage.
In Tanzania, thyristors are used in simple speed controllers for DC motors in small workshop machines such as grinders or water pump controllers. If a student becomes an electronics technician, they may test or replace faulty thyristors in these control units, helping local businesses keep their equipment working without buying expensive new parts.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- The student should be able to:
- Select tools, equipment, safety gear, and components.
- Construct circuit.
- Connect test equipment.
- Perform component characteristics test.
- Record test results
- Observe safety measures
- Clean workplace
- Store tools, equipment, safety gear and components
Tathmini ya matokeo
Thyristor Test results conform to standard characteristics.
Tathmini ya maarifa
Knowledge evidence:
Methods used: The student should explain how to test the characteristics of the thyristor.
Principles: The student should explain the principles related to testing characteristics of Thyristor.
Theories: The trainee should explain: - Semiconductor devices
- The PN junction
- Properties of semiconductors
Circumstantial knowledge:
Detailed knowledge about:
- Semiconductors and their characteristics
Swali
What is a thyristor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado