Mada za sehemu hiiPerforming solderingMada 2
- Carrying out soft soldering
- Carrying out hard soldering
Hard soldering is a method of joining metal pieces using a special solder (called hard solder or silver solder) that melts at a high temperature, usually above 450°C. The high temperature creates a very strong joint that can withstand greater heat and mechanical stress than soft soldering. In electrical installation work in Tanzania, hard soldering is used when a durable and reliable connection is needed, such as joining copper pipes for gas lines or creating strong electrical connections that must last many years.
The temperature required for hard soldering depends on the type of solder being used:
- Silver solders (hardtite): 600°C to 750°C
- Brazing alloys: 700°C to 900°C
The correct temperature is reached when the metal being joined turns a cherry-red color and the solder flows freely into the joint. A blow lamp (torch) is used to achieve these high temperatures, unlike soft soldering which uses a lower-temperature soldering iron.
Before starting hard soldering, gather all required tools:
- Blow lamp (torch) and fuel cylinder
- Hard solder (silver solder or brazing rod)
- Flux (borax or specialized hard solder flux)
- Soldering iron (for pre-heating in some cases)
- Soldering stand
- Diagonal cutting pliers
- Combination pliers
- Long nose pliers
- Adjustable third hand with magnifying glass
- Pot and ladle (for holding flux)
- Electrician knife
- Fire-resistant cloth or sand bucket (for safety)
Always wear proper protective equipment:
- Safety goggles (to protect eyes from sparks and hot metal)
- Safety boots (to protect feet from hot objects)
- Overalls (to protect skin from burns)
- Safety gloves (heat-resistant gloves)
Step 1: Prepare the Joint
Clean the metal surfaces to be joined using an electrician knife or sandpaper. Remove all rust, grease, oil, and oxidation. The surfaces must be completely clean for the solder to flow properly and create a strong bond.
Step 2: Fit the Joint
Fit the pieces together properly before applying heat. Ensure there is a small gap (about 0.05mm to 0.1mm) between the pieces—this gap allows the capillary action to draw the molten solder into the joint.
Step 3: Apply Flux
Apply flux to the joint using a brush or ladle. The flux protects the metal from oxidation during heating and helps the solder flow smoothly. Cover all surfaces that will be heated.
Step 4: Secure the Work
Use an adjustable third hand, clamps, or a soldering stand to hold the work pieces steady. Moving the work while heating can ruin the joint.
Step 5: Heat the Joint
Light the blow lamp and direct the flame at the base metal, not directly at the solder. Heat the joint evenly until the metal reaches the correct temperature. The metal will glow a cherry-red color when it is hot enough.
Step 6: Apply the Solder
Once the metal is hot enough, touch the hard solder to the edge of the joint (not the flame). If the temperature is correct, the solder will melt and flow into the joint by capillary action. Add enough solder to fill the joint completely without excess.
Step 7: Allow to Cool
Let the joint cool naturally in the air. Do not quench it with water as this can cause the joint to crack. The cooling rate should be slow and even.
Step 8: Clean the Joint
After cooling, remove any excess flux residue using a wire brush or damp cloth. Inspect the joint to ensure it is smooth, complete, and free of pores.
A student at VETA training center needs to join two copper tubes for a gas installation project. The tubes have an external diameter of 15mm and need to be joined using silver solder.
Procedure followed:
- Cleaned both tube ends with emery cloth
- Inserted the tube ends into a proper fitting with 0.08mm gap
- Applied borax flux to both joints using a brush
- Clamped the tubes in a fixed position
- Heated the joint using a blow lamp until cherry-red color appeared
- Touched silver solder (hardtite) to the joint edge
- Solder flowed smoothly and filled the gap
- Allowed to cool naturally for 5 minutes
- Cleaned flux residue with water and dried
The resulting joint was strong, leak-free, and suitable for the gas installation.
In Tanzania, hard soldering is commonly used by motorcycle and car mechanics in local workshops when repairing fuel lines or exhaust systems, where joints must withstand high temperatures. A technician at a garage in Dar es Salaam would use hard soldering to join copper pipes in a customer's motorcycle fuel system, ensuring a leak-proof connection that can handle the heat generated by the engine—something a weak joint made with soft soldering could never survive.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify tools, safety gears, equipment, and materials required.
- Prepare the parts to be soldered.
- Heat the surface thoroughly.
- Solder the parts.
- Remove surplus solder using a wire brush.
- Safety precautions.
- Clean the work area.
Tathmini ya matokeo
The joint soldered is mechanically and electrically sound.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to carry out soft soldering.
Principles: The student should explain the principles of carrying out soft soldering.
Theories: The student should explain:
- Types of soldering materials.
- Application of soft soldering.
- The uses of various tools and equipment.
Detailed knowledge about:
- Safe handling of working tools and materials
Swali
What is the minimum temperature at which hard soldering typically occurs?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado