Mada za sehemu hiiInstalling lighting circuitsMada 4
- Installing lighting points controlled by one way one gang switch
- Installing lighting points controlled by one, two, and three-way gang switches
- Installing lighting points controlled by two two-way switches
- Installing lighting points controlled by two-two-way switches and an intermediate switch
A one-way one-gang switch (also called a single-pole switch) is a simple switch that has one input terminal and one output terminal. It is mounted on a single gang (one switch plate) and is used to turn a light ON or OFF from one location only.
The key words mean:
- One-way — the light can only be controlled from one switch position (not from two places like a two-way switch)
- One-gang — there is only one switch on the mounting plate
This is the most common switch used in homes, classrooms, and small buildings in Tanzania.
The one-way one-gang switch is used to:
- Connect or disconnect the live (phase) wire in a lighting circuit
- Allow a person to control one lighting point from a single switch location
- Switch the lamp off so that a failed bulb can be changed
The wall switch is not a means of isolation. Before anyone works on the lamp holder, the switch or the wiring, the circuit must be switched off and locked off at the distribution board and proved dead.
When the switch is ON, the circuit is complete and the lamp lights. When the switch is OFF, the circuit is broken and the lamp goes out.
For this installation, you need the following components:
| Component | Purpose |
|---|---|
| One-way one-gang switch | Controls the ON/OFF of the light |
| Lamp holder (batten holder) | Holds the lamp/bulb |
| Lighting point (lamp) | Provides illumination |
| Twin and earth (T&E) cable 1.5 mm² | Carries current to the lamp |
| 6 A circuit breaker (or 5 A fuse) in the distribution board | Protects the lighting circuit against overload and short circuit |
| Insulated connector block | Joins the neutral conductors in the switch box |
| Green-and-yellow sleeving | Covers the bare earth conductor at each termination |
| Junction box / switch box | Houses the switch |
| Conduit or cable clips | Protects and holds cables |
In a one-way switching circuit, the wiring follows this path:
- Live (Line/L) — from the distribution board to one terminal of the switch
- Switched Live — from the other terminal of the switch to the lamp holder
- Neutral (N) — runs from the distribution board to the lamp holder without being connected to the switch. Where the cable passes through the switch box, the neutral conductors are joined in an insulated connector
- Earth (E) — the circuit protective conductor runs to every point of the circuit, including the switch box, and connects any metal parts to earth for safety
DB 6 A breaker -- L --> COM [switch] L1 -- switched live --> lamp holder (L)
DB neutral bar -- N --> connector in switch box ----------> lamp holder (N)
DB earth bar ---- E --> earth terminal of switch box -----> earth terminal at lamp
When the switch is pressed ON, current flows from Live → through switch → to lamp → and returns through Neutral, completing the circuit.
Before installing, prepare the drawings for the job:
- A layout drawing shows where the switch, the lamp and the distribution board are on the plan of the room
- A circuit diagram shows how the circuit works, using symbols
- A wiring diagram shows each conductor and the terminal it connects to
Common symbols:
| Item | Symbol |
|---|---|
| Lamp | A circle with a cross inside |
| One-way switch (layout drawing) | A small circle with a short sloping line ending in one tick |
| One-way switch (circuit diagram) | A gap in the line with a hinged contact that closes it |
| Fuse | A small rectangle with the line passing through it |
| Earth | A vertical line ending in three short horizontal lines, each shorter than the one above |
Step 1: Gather Tools and Safety Gear
Before starting, collect all required tools and wear protective equipment:
- Combination pliers, screwdriver set, electrician knife
- Measuring tape, spirit level, hacksaw
- Multimeter (for testing)
- Safety boots, overalls, and gloves
Then make the circuit safe. Switch off the circuit at the distribution board, lock it off (or remove the fuse and keep it with you) and hang a warning notice. Prove that the circuit is dead with a voltage tester, checking the tester on a known supply or proving unit before and after the test.
Step 2: Plan the Circuit Route
- Decide where the switch will be mounted (usually near a door entry point)
- Decide where the lighting point (lamp holder) will be fixed on the ceiling or wall
- Plan the cable route from the distribution board → switch → lamp
Step 3: Install the Switch Box
- Mark the position for the switch box using a pencil and spirit level
- Fix the box securely to the wall at the height shown on the drawing (commonly about 1.2 m to 1.4 m above the finished floor)
Step 4: Install the Lamp Holder
- Fix the lamp holder (batten holder) at the planned ceiling or wall position
- Ensure it is firmly secured
Step 5: Run the Cable
- Run twin and earth (T&E) cable from the distribution board to the switch position
- Run another cable from the switch to the lamp holder
- Run the cables only vertically or horizontally in line with the switch and lamp positions, never diagonally across a wall
- Use cable clips or conduit to support and protect the cables along the route
Step 6: Connect the Switch
- Strip the cable ends using an electrician knife carefully
- Identify the COM (common) terminal and the L1 terminal on the switch
- Connect the live wire from the distribution board to the COM terminal
- Connect the switched live wire (going to the lamp) to the L1 terminal
- Join the two neutral conductors (blue; black in older cable) in an insulated connector inside the box. They are not connected to the switch
- Cover the bare earth conductors with green-and-yellow sleeving and connect them to the earth terminal of the switch box
- Tighten all terminal screws securely, with no bare copper showing outside the terminals
Step 7: Connect the Lamp Holder
- At the lamp holder, connect:
- Neutral wire (blue; black in older cable) — to the neutral terminal of the holder
- Switched live wire (brown; red in older cable) — from the switch L1 terminal
- Earth wire (green/yellow) — to the earth terminal of the holder
Step 8: Test the Installation
- Double-check all connections are tight and correct, then fit the switch plate and all covers so that no terminal can be touched
- With the supply still off, use the multimeter on the resistance range to check three things: the earth conductor is continuous from the distribution board to the lamp holder; there is no connection (a very high reading) between live and neutral with the lamp removed, or between live and earth; and the switch opens and closes the live conductor, not the neutral
- Where an insulation resistance tester is available, the insulation resistance is also measured before the circuit is energised
- Only when these tests are correct and the work has been checked by your instructor, fit the lamp, remove the lock and switch on the power supply
- Press the switch — the lamp should light up
- Press again — the lamp should go off
Step 9: Complete and Finish
- Check once more that every cover and plate is fitted and firm
- Clean the work area: sweep up cable offcuts, insulation strippings and dust, and put them in the waste bin
- Wipe the tools, and return the tools, the multimeter and the unused cable and accessories to the store
- Always switch off and isolate the power supply before starting any work
- Never work on a live circuit
- Lock off the supply and prove dead with a voltage tester before touching any conductor
- Use proper insulated tools
- Wear safety boots and gloves at all times
- Ensure all earth connections are properly made
- Test all connections before restoring power
A technician needs to install a lighting point in a standard classroom at a secondary school in Arusha. The lamp holder will be mounted on the ceiling above the teacher's desk. The switch will be mounted near the classroom door at a height of 1.2 m.
Cable routing:
- From the distribution board, run a T&E cable to the switch box near the door
- From the switch, run another T&E cable to the ceiling lamp holder
Connections at the switch:
- Live (L) from DB → COM terminal of the switch
- Switched live from L1 terminal → to the lamp holder
- The two neutral conductors are joined in a connector, and the earth conductors go to the earth terminal of the box
Connections at the lamp holder:
- Neutral (N) from DB → neutral terminal of holder
- Switched live from switch → live terminal of holder
- Earth (E) → earth terminal of holder
After wiring, the circuit is tested with the supply off and then energised. When the switch is pressed ON, the lamp lights up. When pressed OFF, the lamp goes out. The installation is correct.
The resistance of a metal conductor rises as it gets hotter. For copper the rise is about 0.4% for each degree Celsius. For example, a conductor with a resistance of 1.0 Ω at 20 °C has a resistance of about 1.0 × (1 + 0.004 × 50) = 1.2 Ω at 70 °C.
Current heats a cable. If a cable is too small for its load, bunched tightly with other cables or buried in thermal insulation, it runs hot. PVC insulation softens and is damaged above about 70 °C, which can lead to a short circuit or fire. This is why the cable size and the rating of the fuse or circuit breaker must match the load.
Installation work follows the IEE Wiring Regulations and the rules of the electricity supplier. For this circuit the main requirements are:
- A single-pole switch is connected in the live (line) conductor only, never in the neutral
- Every circuit is protected by a fuse or circuit breaker of the correct rating
- An earth (circuit protective) conductor is run to every lighting point and switch position
- Cables are supported, protected from damage and correctly identified by colour
- The installation is inspected and tested before it is put into service
- Connecting the switch in the neutral wire instead of the live wire. The lamp would still go off, but the lamp holder would stay live when the switch is off
- Leaving terminal screws loose, causing poor contact and overheating
- Forgetting to connect the earth wire
- Working on a live circuit
- Using cable that is too small for the circuit (1.5 mm² copper is the usual size for lighting circuits)
A one-way one-gang switch controls a lighting point from a single location. The live wire passes through the switch so it can be interrupted. The neutral is never switched, and the earth wire runs to every point. Proper installation follows a clear sequence: plan the route, isolate the supply and prove it dead, fix boxes, run cables, connect the switch, connect the lamp holder, test, and finish. Always observe electrical safety rules.
In Tanzania, electricians use one-way one-gang switches to wire lighting in homes, classrooms, and shops. For example, an electrician in Mwanza wiring a new house would install a switch near the main door so that when you enter a room you can easily turn the ceiling lamp on or off using a single switch, without needing to walk to the lamp itself. This simple circuit is the foundation of all household electrical wiring in Tanzania.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Prepare electrical drawings.
- Identify tools, equipment, and materials required.
- Prepare accessories and cables for lighting circuits.
- Install lighting circuit.
- Test the installation.
- Apply safety measures.
- Clean work area.
- Store tools, equipment and remaining materials.
Tathmini ya matokeo
Lighting circuits controlled by a one-way switch one-gang installed as per standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to install lighting points controlled by one-way one-gang switch.
Principles: The student should explain the principles of Installing lighting points controlled by one way one gang switch.
Theories: The student should explain:
- Electrical symbols used in wiring diagram.
- Tools and equipment in wiring circuits.
- Effect of temperature in conducting materials.
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions.
- IEE regulations.
Swali
What does the term one-way tell you about a one-way one-gang switch?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado