Mada za sehemu hiiConstructing simple heating coilsMada 2
- Building circuit with heating coils in series
- Building a circuit with heating coils in parallel
A heating circuit with heating coils in series is built by connecting all coils end-to-end so that the same electric current passes through each coil while the total voltage is divided among them. This arrangement results in a total resistance equal to the sum of all individual coil resistances, and the heat produced by each coil depends on its individual resistance and the current flowing through it.
A series heating circuit is a simple electrical circuit where two or more heating coils are connected one after another in a single continuous path from the power source. When electric current flows through this path, it passes through each coil in sequence before returning to the power source. This configuration is commonly used in some electrical heating appliances where consistent heating is required across all elements.
When heating coils are connected in series, three important electrical properties apply:
Same Current Through All Coils The electric current that flows through the first coil is the same current that flows through the second coil and all subsequent coils. This is because there is only one path for the current to follow. The current value can be measured using an ammeter placed anywhere in the series loop.
Voltage is Divided Across Coils The total voltage from the power source is shared among the coils. Each coil receives a portion of the total voltage depending on its resistance. If one coil has higher resistance than another, it will drop more voltage across it.
Total Resistance Adds Up The overall resistance of the series circuit equals the sum of all individual coil resistances plus any additional resistance (such as a current-limiting resistor). Mathematically:
Rtotal=R1+R2+R3+...
For example, if three heating coils have resistances of 10Ω, 15Ω, and 20Ω respectively, the total resistance would be:
Rtotal=10Ω+15Ω+20Ω=45Ω
To build a series heating circuit, you need the following components:
- AC power supply (or DC power source)
- Two or more heating coils (made from nichrome or tungsten wire)
- Connecting wires
- Switch (to turn the circuit ON/OFF)
- Current-limiting resistor (to reduce current to a desired level)
- Ammeter (to measure current flow)
- Voltmeter (to measure voltage across coils)
- Fuse or Miniature Circuit Breaker (MCB) for protection
- Personal Protective Equipment (PPE) including overalls and safety goggles
Follow these steps to build a circuit with heating coils connected in series:
-
Prepare your work area — Wear appropriate PPE and ensure your workbench is clean and organized.
-
Study the circuit diagram — Look at the wiring diagram to understand how components should be connected.
-
Select tools and materials — Gather all required components from the list above.
-
Connect the coils in series — Attach the heating coils end-to-end, connecting one end of the first coil to the power source and the other end to one end of the second coil. Continue until all coils are connected in a single chain.
-
Add the switch and protection device — Connect the switch and fuse or MCB in series with the coil assembly.
-
Have your wiring checked — Ask your teacher to inspect the circuit before applying power.
-
Power the circuit — Switch ON the circuit after teacher approval.
-
Take measurements — Use the multimeter to measure and record the current flowing through the circuit and the voltage across each individual coil.
-
Observe heat production — Allow the circuit to run for a set time (such as 30 seconds) and observe how each coil heats up.
-
Switch off and cool down — Turn OFF the circuit and wait for coils to cool before touching them.
-
Calculate and record results — Use the measurements to calculate heat produced, resistance, and power for each coil.
Problem: Two heating coils with resistances of 8Ω and 12Ω are connected in series to a 240V AC supply. A current-limiting resistor of 20Ω is also included in the circuit. Calculate:
(a) The total resistance of the circuit (b) The current flowing through the coils (c) The voltage across each heating coil
Solution:
(a) Total resistance: Rtotal=R1+R2+Rlimiting Rtotal=8Ω+12Ω+20Ω=40Ω
(b) Current flowing through the circuit (using Ohm's Law): I=RtotalV=40Ω240V=6A
(c) Voltage across each heating coil:
For the 8Ω coil: V1=I×R1=6A×8Ω=48V
For the 12Ω coil: V2=I×R2=6A×12Ω=72V
Note: The sum of individual voltages (48V + 72V = 120V) is less than the supply voltage because part of the voltage (120V) is dropped across the current-limiting resistor.
When building and testing series heating circuits, always observe these safety rules:
- Ensure all components are correctly rated for the expected voltage and current
- Use only insulated, heat-resistant wires and terminals
- Never touch the coils while the power is ON — they become very hot
- Always have your teacher check the circuit before switching on power
- Keep flammable materials away from heating elements
- Use fuses or MCBs to protect against overloads
- Switch OFF immediately if you notice unusual heating or sparking
In Tanzania, series heating circuits are found in some simple electric cookers and water heating elements used in small guesthouses or restaurants. For example, a local restaurant in Dar es Salaam might use a series-connected heating element in a food warming tray where consistent, lower-power heat is needed across the entire surface. Understanding how series circuits behave helps electricians troubleshoot when such heating equipment fails to heat properly or stops working entirely.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment and safety gear.
- Design a circuit diagram of the heating circuit.
- Prepare heating coils for connection.
- Build a series coils circuit.
- Supply power to the circuits.
- Perform power measurement.
- Test the circuits.
- Observe safety precautions.
Tathmini ya matokeo
Heating circuits are constructed in series as per IEE regulations and the test results conform to approved standards and theories.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to build a circuit with heating coils in series.
Principles: The student should explain the principles related to building a circuit with heating coils in series.
Theories: The student should explain:
- The Ohms law and its applications.
- The difference between resistance and impedance.
- The measurement of current in the circuit.
- The measurement of voltage in the circuit.
Detailed knowledge about:
- Safe handling of working tools and equipment.
- Safety rules
Swali
In a series heating circuit, what happens to the electric current as it passes through each heating coil?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado